K55 水轮机及其辅助设备 标准查询与下载



共找到 249 条与 水轮机及其辅助设备 相关的标准,共 17

This International Standard defines the test, the measuring methods and the contractual guarantee conditions for field acceptance tests of the generating machinery in small hydroelectric power installations. It applies to installations containing impulse or reaction turbines with unit power up to about 15 MW and reference diameter of about 3 m. The driven generator can be of synchronous or asynchronous type. This International Standard contains information about most of the tests required for acceptance of the hydraulic turbine such as safety approval tests, trial operating and reliability tests, as well for verification of cavitation, noise and vibration conditions, if required. This standard represents the typical methods used on smaller hydroelectric installations, and is divided into three classes as follows (see Table 1 for more detail): Class A Normal test program (panel measurement) To determine the maximum power output of the installation. Default Class B Extended test program To determine the performance characteristics of the installation. Recommended Class C Comprehensive test program To determine the absolute efficiency of the installation. Optional NOTE All classes contain safety tests, trial operating tests, and reliability tests. This standard gives all necessary references for the contract in order to execute the test, evaluate, calculate and compare the result to the guarantee for all the classes A, B and C. The manufacturer or consulting engineer is responsible for ensuring that standardized connections are installed for performing these tests. This standard does not cover the structural details of a hydroelectric installation or its component parts.

Hydraulic machines - Acceptance tests of small hydroelectric installations

ICS
27.140
CCS
K55
发布
2010-10
实施
2010-10

This International Standard is applicable to the assessment of the efficiency and performance of prototype hydraulic machine from model test results, with consideration of scale effect including the effect of surface roughness. This standard is intended to be used for the assessment of the results of contractual model tests of hydraulic machines.

Hydraulic machines, radial and axial - Performance conversion method from model to prototype

ICS
27.140
CCS
K55
发布
2009-07-31
实施
2009-07-31

Glossary of terms for hydraulic turbines and reversible pump-turbines

ICS
01.040.23;23.080
CCS
K55
发布
2009-03-20
实施

本标准适用于含沙量不超过5Okg/m,中值粒径小于0.lmm的悬移质反击式(包括混流式、斜流式、轴流式及贯流式)水轮机的模型浑水验收试验。

Code of practice for model accepunce tests of hydraulic turbine with sediment water

ICS
93.160
CCS
K55
发布
2008-11-10
实施
2009-02-10

本标准规定了水轮机控制系统的专用术语。 本标准适用于制订水轮机控制方面的标准、编制技术文件及招投标文件,也适用于编写和翻译专业 文献、教材及书刊等。

Electro-technical terminology.Hydraulic turbine control system

ICS
27.140
CCS
K55
发布
2008-02-01
实施
2008-07-01

The scope of this International Standard covers turbines, storage pumps and pump-turbines of all sizes and of the following types: • Francis; • Kaplan; • propeller; • Pelton (turbines only); • Bulb. Wherever turbines or turbine components are referred to in the text of this guide, they shall be interpreted also to mean the comparable units or components of storage pumps or pumpturbines as the case requires. The Guide also identifies without detailed discussion, other powerhouse equipment that could affect or be affected by a turbine, storage pump, or pump-turbine rehabilitation.

Hydraulic turbines, storage pumps and pump turbines - Rehabilitation and performance improvement

ICS
27.140
CCS
K55
发布
2008-01
实施
2017-05-31

This document recommends performance characteristics and equipment for electric-hydraulic governors for all types of hydraulic turbines intended to drive electric generators of all sizes. It is intended to assist users with the preparation of procurement specifications for electric-hydraulic speed governors.

Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators

ICS
27.140
CCS
K55
发布
2007-09-12
实施

本标准规定了水轮机进水液动蝶阀(以下简称进水蝶阀)的分类、技术要求与保证、供货范围与备品备件、专用工具、检验、试验、评定及验收、图纸与资料、标志、包装、运输、贮存、安装、运行及维护等方面的基本要求。 本标准适用于水轮机最大水头小于或等于250m的水轮机进水液动蝶阀;水泵水轮机用液动蝶阀、水轮机最大水头大于250m的水轮机进水液动蝶阀可参照本标准执行。

Specification for hydraulic operation butterfly valve selection,test and acceptance of hydraulic turbine inlet

ICS
27.140
CCS
K55
发布
2007-07-20
实施
2007-12-01

This document recommends performance characteristics and equipment for electric-hydraulic governors for all types of hydraulic turbines intended to drive electric generators of all sizes. It is intended to assist users with the preparation of procurement specifications for electric-hydraulic speed governors.

Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators

ICS
27.140
CCS
K55
发布
2007-06-07
实施

本标准规定了绘制电机、水轮机产品图样的简化画法、示意画法和简化注法等。 本标准适用于电机、水轮机产品图样,其他产品图样也可参照采用。

Simplified regulation of drawing for large middle and small generator and turbine

ICS
27.140
CCS
K55
发布
2006-09-14
实施
2007-03-01

이 규격은 펠톤 터빈 러너에서 캐비테이션 피팅의 보증 형식에 대한 기준으로 그리고 동력,

Cavitation pitting evaluation in hydraulic turbines, storage pumps and pump-turbines-Part 2:Evaluation in Pelton turbines

ICS
27.140
CCS
K55
发布
2006-05-10
实施
2006-05-10

이 규격은 발전기나 전동기에 결합된 반동 터빈이나, 충동 터빈 형태뿐만 아니라 펌프 터빈

Guide for field measurement of vibrations and pulsations in hydraulic machines(turbines, storage pumps and pump-turbines)

ICS
17.160
CCS
K55
发布
2006-05-10
实施
2006-05-10

이 규격은 반동 수력 터빈, 저장 펌프 및 펌프 터빈에 대한 캐비테이션 피팅에 적용되는 보

Hydraulic turbines, storage pumps and pump-turbines-Cavitation pitting evaluation-Part 1:Evaluation in reaction turbines, storage pumps and pump-turbines

ICS
23.100.10
CCS
K55
发布
2006-05-10
实施
2006-05-10

This International Standard applies to laboratory models of any type of impulse or reaction hydraulic turbine, storage pump or pump-turbine. This standard applies to models of prototype machines either with unit power greater than 5 MW or with reference diameter greater than 3 m. Full application of the procedures herein prescribed is not generally justified for machines with smaller power and size. Nevertheless, this standard may be used for such machines by agreement between purchaser and supplier. In this standard, the term "turbine" includes a pump-turbine operating as a turbine and the term "pump" includes a pump-turbine operating as a pump. This standard excludes all matters of purely commercial interest, except those inextricably bound up with the conduct of the tests. This standard is concerned with neither the structural details of the machines nor the mechanical properties of their components, so long as these do not affect model performance or the relationship between model and prototype performances.

Hydraulic turbines, storage pumps and pump-turbines — Model acceptance tests

ICS
27.140
CCS
K55
发布
2006-04-28
实施
2006-04-28

이 규격은 제어 시스템의 정의 및 특성 등을 규정하고, 입찰 서류와 기술 입찰에 대한 기준

Hydraulic turbines-Testing of control systems

ICS
27.140
CCS
K55
发布
2006-02-28
实施
2006-02-28

이 규격은 수력 터빈 제어 시스템을 기술하고 그 성능을 정의하는데 필요한 관련 기술 데이터

Guide to specification of hydraulic turbine control systems

ICS
27.140
CCS
K55
发布
2006-02-28
实施
2006-02-28

이 규격의 목적은 일반적인 방법으로 수력 터빈과 관련 설비의 시운전에 대한 적합성 평가 절

Guide for commissioning, operation and maintenance of hydraulic turbines

ICS
23.100.10
CCS
K55
发布
2006-02-28
实施
2006-02-28

本标准适用于与水轮机直接连接的3相50Hz、额定容量为25MVA及以上的立轴凸极同步发电机(以下简称水轮发电机)。额定容量25MVA以下的立轴凸极同步发电机及卧轴水轮发电机可参照执行。

Fundamental technical specifications for large and medium hydrogenerators

ICS
27.140
CCS
K55
发布
2005-05-10
实施
2005-07-01

Hydraulic turbines, storage pumps and pump-turbines - Cavitation pitting evaluation - Part 1 : evaluation in reaction turbines, storage pumps and pump-turbines.

ICS
23.080;27.140
CCS
K55
发布
2005-04-01
实施
2005-04-20

Deals with the definition and the characteristics of control systems. It is not limited to the actual controller tasks but also includes other tasks which may be assigned to a control system, such as sequence control tasks, safety and provision for the a

Hydraulic turbines - Testing of control systems

ICS
27.140
CCS
K55
发布
2005-01
实施
2005-02-01



Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号