K64 电动工具 标准查询与下载

CSA C22.2 No.60745-2-14-04 AMD 1-2007 手持式马达操作电动工具 安全性.第2-14部分:刨子的特殊要求

Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose.

Amendment 1 Hand-held motor-operated electric tools ?Safety ?Part 2-14: Particular requirements for planers [Superseded: CSA C22.2 NO 745-4-14-95]

DIN EN 60745-1:2007 手持式电动工具.安全.第1部分:一般要求

Hand-held motor-operated electric tools - Safety - Part 1: General requirements (IEC 60745-1:2006, modified); German version EN 60745-1:2006

DIN EN 60745-2-1:2007 手持式电动工具.安全.第2-1部分:电钻和冲击钻的特殊要求

Hand-held motor-operated electric tools - Safety - Part 2-1: Particular requirements for drills and impact drills (IEC 60745-2-1:2003, modified); German version EN 60745-2-1:2003 + A11:2007

CSA C22.2 No.60745-2-3-07-2007 手持式马达操作电动工具 安全性.第2-21部分:污水清洁器的特殊要求.第2版

Hand-held motor-operated electric tools Safety Part 2-21: Particular requirements for drain cleaners Second Edition

Hand-held motor-operated electric tools Safety Part 2-21: Particular requirements for drain cleaners Second Edition

UL 60745-2-3-2007 安全手持式电动工具用UL标准.安全性.第2-3部分:研磨机、抛光机和盘式砂轮机的详细要求

This clause of part 1 is applicable, except as follows: 1.1 Addition: This standard applies to GRINDERS, with a RATED SPEED not exceeding a peripheral speed of the accessory of 80 m/s at rated capacity, polishers and disk-type sanders, including angle, straight and vertical. This standard applies to tools with a rated capacity not exceeding 230 mm. This standard does not apply to random-orbit polishers and random-orbit sanders. These are covered by IEC 60745-2-4.

UL Standard for Safety Hand-Held Motor-Operated Electric Tools ?Safety ?Part 2-3: Particular Requirements for Grinders, Polishers and Disk-Type Sanders

CSA C22.2 No.60745-2-3-07-CAN/CSA-2007 带电机的电动工具 安全 第2-3部分：盘式磨床、抛光机和砂光机的特殊规则 第二版

L’Association canadienne de normalisation (CSA), sous les auspices de laquelle cette Norme nationale a été préparée, a re?u ses lettres patentes en 1919 et son accréditation au sein du Système de Normes nationales par le Conseil canadien des normes en

Power tools with motor — Safety — Part 2-3: Particular rules for grinders, polishers and sanders of the disc type second edition

SN/T 1657.3-2006 进出口电动工具检验规程 第3部分：手持式电刨

Rules for the inspection of motor-operated electric tools import and export-Part 3:hand-held electric planers

NF C75-745-2-1/A11:2007 手持式电动工具.安全性.第2-1部分:电钻和冲击电钻的特殊要求

Hand-held motor-operated electric tools - Safety - Part 2-1 : particular requirements for drills and impact drills.

NF E74-363-2:2007 螺钉和螺母用装配工具.方形驱动套筒.第2部分:机器驱动套筒(冲击)

Assembly tools for screws and nuts - Square drive sockets - Part 2 : machine-operated sockets ("impact").

SANS 60745-2-6:2007 手持式电动工具．安全性．第2．6部分：锤子的特殊要求

Deals with the safety of hand-held motor-operated or magnetically driven hammers, the rated voltage of the hammers being not more than 250 V for single-phase a.c. or d.c. hammers, and 440 V for three-phase a.c. hammers. Includes, but are not limited to,

Hand-held motor-operated electric tools - Safety Part 2-6: Particular requirements for hammers

SN/T 1657.6-2007 进出口电动工具检验规程 第6部分:高压清洗机

SN/T 1657 的本部分规定了进出口高压清洗机的要求、检验及判定。 本部分适用于压力在 2.5MPa～25MPa 之间，额定电压不超过 250 V 的高压清洗机的进出口检验。

Rules for the inspection of electric tools for import and export.Part 6: High pressure cleaners

ANSI/ASME B107.44-2007 凿子.按装玻璃用细长凿、地板装饰和电工用凿

This Standard provides performance and safety requirements for glaziers' chisels, wood chisels, ripping chisels and flooring/electricians' chisels. Glaziers' chisels are intended for installing and removing putty around window panes and for general wood chisel work relating to glazing. Wood chisels are intended for making rough and finish cuts in wood. Ripping and flooring/electricians' chisels are intended for use in cutting wood and light prying, such as cutting the tongue of installed flooring sections and raising and removing floor planks. It is intended to serve as a guide in selecting, testing, and using the hand tools covered. It is not the purpose of this Standard to specify the details of manufacturing.

Chisels - Glaziers, Wood, Ripping, Flooring/Electricians

DLA A-A-50473 B VALID NOTICE 2-2007 按键手动加油器

A-A-50473B, dated 27 September 2001, has been reviewed and determined to be valid for use in acquisition.

OILERS, HAND, PUSH-BOTTOM

JIS C 9029-2-8 ERRATUM 1:2007 勘误

ERRATUM

JIS C 9029-1 ERRATUM 1:2007 勘误

ERRATUM

JIS C 9029-2-7 ERRATUM 1:2007 勘误

ERRATUM

JIS C 9029-2-4 ERRATUM 1:2007 勘误

ERRATUM

JIS C 9029-2-11 ERRATUM 1:2007 勘误

ERRATUM

UL 745-4-11-2007 蓄电池供电的往复式锯用特殊要求

This clause of Part 3 is applicable, except as follows: 1.1 Replacement:The term "tool" is replaced with "reciprocating saws" (jig and sabre saws). For the purpose of this standard, a jig saw is the type generally used for cutting patterns in lumber and is generally held by one hand; a sabre saw is generally used in demolition work cutting openings in walls, or ceilings, or in construction for cutting off of pipes and the like, and is always held with both hands.

UL Standard for Safety Particular Requirements for Battery-Operated Reciprocating Saws Second Edition

ANSI/UL 60745-1-2007 手持式机动电动工具标准.安全.第1部分:一般要求

Adoption of the Fourth Edition of IEC 60745-1, Hand-Held Motor-Operated Electric Tools - Safety - Part 1: General Requirements as the Fourth Edition of UL 60745-1.

UL Standard for Safety Hand-Held Motor-Operated Electric Tools �C Safety �C Part 1: General Requirements (Fourth Edition; Reprint with Revisions Through and Including November 28@ 2016)