K71 电光源产品 标准查询与下载

JIS C 7613 AMD 1:2011 用于光度标准器的白织灯的光度测量(修改件1)

Photometric measurements on incandescent lamps used for photometric standards (Amendment 1)

DIN EN 60357:2011 卤钨灯(非机动车辆用)-性能规范(IEC 60357-2002,修订版 + A1-2006, 修订版 + A2-2008 + A3-2011);德文版本EN 60357-2003 + Cor.-2003 + A1-2008 + A2-2008 + A3-2011

Tungsten halogen lamps (non-vehicle) - Performance specifications (IEC 60357:2002, modified + A1:2006, modified + A2:2008 + A3:2011); German version EN 60357:2003 + Cor. :2003 + A1:2008 + A2:2008 + A3:2011

BS EN 61167:2011 金属卤化物灯.性能规范

This International Standard specifies the performance requirements for metal halide lamps for general lighting purposes. For some of the requirements given in this standard, reference is made to “the relevant lamp data sheet”. For some lamps, these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer’s production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that product manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.

Metal halide lamps. Performance specification

BS EN 62532:2011 荧光感应灯.安全规范

Fluorescent induction lamps. Safety specifications

IEC 62554:2011 测量荧光灯内汞含量的样品的制备

This International Standard specifies sample preparation methods for determining mercury levels in new tubular fluorescent lamps (including single capped@ double capped@ self-ballasted and CCFL for backlighting) containing 0@1 mg mercury or more. The intended resolution of the methods described in this standard is of the order of 5 %. Mercury level measurement of spent lamps is excluded@ as during lamp operation@ mercury gradually diffuses into the glass wall and reacts with the glass materials. The test method of this standard does not recover mercury that is diffused into or reacted with or otherwise incorporated irreversibly with the glass wall of discharge tubes. This standard does not contain information on measurement. Measurement is specified in IEC 62321.

Sample preparation for measurement of mercury level in fluorescent lamps

JIS C 7605:2011 杀菌灯

This Standard specifies the germicidal lamps of which the mercury vapour pressure in a tube at the time of lighting is about 100 Pa or less.It does not apply to those ger-micidal lamps integral with an arc tube,ballast and an starting point.

Germicidal lamps

IEC 61199:2011 单头荧光灯.安全性规范

This International Standard specifies the safety requirements for single-capped fluorescent lamps for general lighting purposes of all groups having caps according to Table 1. It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given in this standard. NOTE Compliance with this standard concerns only safety criteria and does not take into account the performance of single-capped fluorescent lamps for general lighting purposes with respect to luminous flux@ colour@ starting and operational characteristics. For this information@ readers are referred to IEC 60901. It may be expected that lamps which comply with this standard will operate safely at supply voltages between 90 % and 110 % of rated supply voltage of the used ballast and when operated with a ballast complying with IEC 61347-2-3 or IEC 61347-2-8 with a starting device complying with IEC 60155 (if applicable) and in a luminaire complying with IEC 60598-1.

Single-capped fluorescent lamps - Safety specifications

IEC 62386-209:2011 数字可寻址照明接口.第209部分:控制装置的详细要求.色度控制(设备类型8)

Digital addressable lighting interface - Part 209: Particular requirements for control gear - Colour control (device type 8)

UL 1598C-2011 发光二极管 (LED) 改装灯具转换套件的调查大纲 (第一版)

OUTLINE OF INVESTIGATION FOR LIGHT-EMITTING DIODE (LED) RETROFIT LUMINAIRE CONVERSION KITS (First Edition)

KS C 4306-2011 单套管式电流互感器

이 표준은 주위 온도 최고 40 ℃ 이하 최저 -25 ℃ 표고 1000 m 이하인 장소에서

Single high voltage cover bushing transformers

IEC 62386-210:2011 数字可寻址照明接口.第210部分:控制装置的详细要求.序列发生器(装置类型9)

This International Standard specifies a protocol and test procedures for the control by digital signals of electronic control gear working as automatic sequencers.

Digital addressable lighting interface - Part 210: Particular requirements for control gear - Sequencer (device type 9)

CJ/T 361-2011 水景用发光二极管（LED）灯

本标准规定了水景用发光二极管（LED）灯的术语和定义、缩略语、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于水景、音乐喷泉、瀑布、喷水池等场所使用的发光二极管（LED）灯。 本标准不适用于游泳池、浴室等与人体直接接触的场所。

Light emitting diode(LED) lamp used in waterscape

JIS C 7551-2:2011 白炽灯.安全性规范.第2部分:家用和类似照明用途的卤钨灯

Incandescent lamps -- Safety specifications -- Part 2: Tungsten halogen lamps for domestic and similar general lighting purposes

JIS C 7551-3:2011 白炽灯.安全性规范.第3部分:卤钨灯(非机动车)

Incandescent lamps -- Safety specifications -- Part 3: Tungsten halogen lamps (non-vehicle)

IEC 60662:2011 高压钠蒸汽灯.性能规格

This standard specifies the characteristics of high-pressure sodium vapor lamps necessary to ensure interchangeability and safety together with test conditions and procedures. The recommendations relate only to type testing. The standard specifies the lamp dimensions@ electrical characteristics for lamp starting and operation together with information for ballast@ ignitor and luminaire design purposes. The requirements dealing with the lamp starting test and associated information for ballast/ignitor design are different depending on the practice of the country in which the lamp type was originally developed. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample submitted by the manufacturer for that purpose. In principle@ this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that product manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however@ it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes@ see IEC 60410.

High pressure sodium vapour lamps - Performance specifications

IEC 62560:2011 电压＞50 V的普通照明服务用自压载发光二极管灯.安全性规范

"This International Standard specifies the safety and interchangeability requirements@ together with the test methods and conditions required to show compliance of LED-lamps with integrated means for stable operation (self-ballasted LED-lamps)@ intended for domestic and similar general lighting purposes@ having: ?C a rated wattage up to 60 W; ?C a rated voltage of > 50 V up to 250 V; ?C caps according to Table 1. The requirements of this standard relate only to type testing. Recommendations for whole product testing or batch testing are identical to those given in Annex C of IEC 62031. NOTE Where in this standard the term ""lamp(s)"" is used@ it is understood to stand for ""self-ballasted LEDlamp( s)""@ except where it is obviously assigned to other types of lamps."

Self-ballasted LED-lamps for general lighting services by voltage > 50 V - Safety specifications

DB65/T 3370-2012 太阳能LED道路照明装置技术条件

Technical requirements ofpVLEDlighting system

ANSI C136.29-2011 道路和区域照明设备.金属卤素灯.选用指南

Includes screw-base single-ended metal halide lamps that can be used in roadway and area lighting equipment.

Roadway and Area Lighting Equipment - Metal Halide Lamps - Guide for Selection

IEC 60357:2002/AMD3:2011 卤钨灯(非车辆用).性能规范

This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps@ having rated voltages of up to 250 V@ used for the following applications:?? Projection (including cinematograph and still projection)?? Photographic (including studio)?? Floodlighting?? Special purpose?? General purpose?? Stage lighting For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps@ falling under the scope of this standard@ the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE ?The requirements and tolerances permitted by this standard correspond to testing of a type test sample@ submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturerapos;s production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however@ it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes@ see IEC 60410.

Tungsten halogen lamps (non-vehicle) - Performance specifications

IEC 62532:2011 荧光电感灯.安全性要求

This International Standard specifies the safety requirements for fluorescent induction lamps for general lighting purposes. It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure, which can be used to make limited assessment of batches, are also given in this standard. The schematic drawings of the systems are shown in Annex A.

Fluorescent induction lamps - Safety requirements