K71 电光源产品 标准查询与下载

ANSI C78.1402-2004 投影灯的尺寸.灯座向下操作基于四脚、预聚焦的G17q和GX17q

This standard established the dimensions essential to the interchangeability of four-pin, prefocus projection lamps for base-down operation of T10 and T12 bulb sizes.

Dimensions for Projection Lamps - G17q and GX17q Based Four-pin, Prefocus, for Base-down Operation

ANSI C78.1406-2004 电灯.灯座向下操作基于投影灯的P28单触点中等预聚焦.尺寸

This project is a revision of ANSI C78.1406-1983 This standard established the dimensions essential to the interchangeability of single-contact medium prefocus based projection lamps of T-10 and T-12 bulb sizes.

Electric Lamps - P28 Single-Contact Medium Prefocus Based Projection Lamps for Base-Down Operation - Dimensions

ANSI C78.1407-2004 电灯.聚光器反光镜、四脚、预聚焦底座投影灯.尺寸

This project is a revision of ANSI C78.1407-1985

Electric Lamps - Condenser-Reflector, Four-Pin Prefocus-Base Projection Lamps - Dimensions

SJ 20871-2003 连续氪弧灯通用规范

General specification for krypton arc lamp

SANS 62035:2003 放电灯（荧光灯除外）．安全规程

Specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes.This International Standard is applicable to low-pressure sodium vapour lamps and to high-intensity discharge (HID) lamps, i.e. high-pressur

Discharge lamps (excluding fluorescent lamps) - Safety specifications

SANS 60662:2003 高压钠蒸汽灯

Specifies the characteristics of high-pressure sodium vapour lamps necessary to ensure interchangeability and safety together with test conditions and procedures. The recommendations relate only to type testing. Specifies the lamp dimensions, electrical

High-pressure sodium vapour lamps

NF C72-106/A4*NF EN 60630/A4:2003 白炽灯的最大灯泡外廓

Maximum lamp outlines for incandescent lamps.

BS EN 60357:2003+A3:2011 卤素灯系列(非车辆).性能规范

Tungsten halogen lamps (non-vehicle). Performance specifications

BS EN 60357:2003 卤钨灯(非车辆用).性能规范

This International Standard specifies the performance requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: · Projection (including cinematograph and still projection) · Photographic (including studio) · Floodlighting · Special purpose · General purpose · Stage lighting For some of the requirements given in this standard reference is made to "the relevant data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor. The requirements of this standard relate only to type testing. NOTE The requirements and tolerances permitted by this standard correspond to testing of a type test sample, submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturer's production and being as close to the production centre point values as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of production. Due to the production spread however, it is inevitable that there will sometimes be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC 60410.

Tungsten halogen lamps (non-vehicle) - Performance specifications

IEC 62035:2003 放电灯(荧光灯除外).安全规范

Specifies the safety requirements for discharge lamps (excluding fluorescent lamps) for general lighting purposes. This International Standard is applicable to low-pressure sodium vapour lamps and to high-intensity discharge (HID) lamps, i.e. high-pressu

Discharge lamps (excluding fluorescent lamps) - Safety specifications

BS EN 60432-3:2003+A2:2008 白炽灯.安全规范.(非车用)卤钨灯

This part of IEC 60432 specifies the safety requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: ? Projection (including cinematograph and still projection) ? Photographic (including studio) ? Floodlighting ? Special purpose ? General purpose ? Stage lighting

Incandescent lamps — Safety specifications — Part 3: Tungsten-halogen lamps (non-vehicle)

BS EN 60432-3:2003 白炽灯安全规范.卤钨灯(非车用)

This part of IEC 60432 specifies the safety requirements for single-capped and double-capped tungsten halogen lamps, having rated voltages of up to 250 V, used for the following applications: · Projection (including cinematograph and still projection) · Photographic (including studio) · Floodlighting · Special purpose · General purpose · Stage lighting This International Standard does not apply to general purpose single-capped tungsten halogen lamps, covered by IEC 60432-2, that are used as replacement for conventional tungsten filament lamps.

Incandescent lamps - Safety specifications - Tungsten-halogen lamps (non-vehicle)

NF C72-101-3:2003 白炽灯.安全规范.第3部分:卤钨灯(非车用)

Incandescent lamps - Safety specifications - Part 3 : tungsten-halogen lamps (non-vehicle).

DIN EN 50107-1:2003 输出电压超过1kV不超过10KV的标志及发光放电管装置.第一部分.一般要求

Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV - Part 1: General requirements; German version EN 50107-1:2002

IEC 62035/AMD1:2003 放电灯(荧光灯除外).安全规范.修改1

This standard is Discharge lamps (excluding fluorescent lamps) - Safety specifications; Amendment 1.

Discharge lamps (excluding fluorescent lamps) - Safety specifications; Amendment 1

JIS C 7617-2:2003 双帽荧光灯.第2部分:性能规范

この規格は，一般照明用直管蛍光ランプの性能要求事項する。

Double-capped fluorescent lamps -- Part 2: Performance specifications

JIS C 7618-2:2003 单帽荧光灯.第2部分:性能规范

この規格は，一般照明用片口金蛍光ランプ(環形を含む)の性能要求事項を規定する。

Single-capped fluorescent lamps -- Part 2: Performance specifications

NF C72-105*NF EN 60357:2003 钨丝卤素灯(非车辆用).性能规范

Tungsten halogen lamps (non-vehicle) - Performance specifications.

IEC 61549:2003 杂类灯

Relevant to lamps not covered elsewhere in the scope of existing IEC standards.

Miscellaneous lamps

IEC 60081:1997/AMD2:2003 双端荧光灯.性能规范.修改件2

This International Standard specifies the performance requirements for double-capped fluorescent lamps for general lighting service. The requirements of this standard relate only to type testing. Conditions of compliance, including methods of statistical assessment, are under consideration. The following lamp types and modes of operation are included: a) lamps having preheated cathodes, designed for operation on a.c. mains frequencies with the use of a starter, and additionally operating on high frequency; b) lamps having preheated high-resistance cathodes, designed for operation on a.c. mains frequencies without the use of a starter (starterless), and additionally operating on high frequency; c) lamps having preheated low-resistance cathodes, designed for operation on a.c. mains frequencies without the use of a starter (starterless), and additionally operating on high frequency; d) lamps having preheated cathodes, designed for operation on high frequency; e) lamps having non-preheated cathodes, designed for operation on a.c. mains frequencies; f) lamps having non-preheated cathodes, designed for operation on high frequency. For some of the requirements given in this standard, reference is made to "the relevant lamp data sheet". For some lamps these data sheets are contained in this standard. For other lamps, falling under the scope of this standard, the relevant data are supplied by the lamp manufacturer or responsible vendor.

Double-capped fluorescent lamps - Performance specifications; Amendment 2