K72 一般灯具 标准查询与下载

JIS C 8105-2-3:2005 灯具.第2-3部分:安全的特殊要求.道路和街道照明用灯具

この規格は，電源電圧1000V以下の白熱電球，蛍光ランブ，その他の放電ランプ，LEDなど電子発光体を用いた，次に記載する照明器具(以下,照明器具という。)の一般的安全性の要求事項及び試験方法について規定する。

Luminaires -- Part 2-3: Particular requirements for safety -- Luminaires for road and street lighting

JIS C 8105-2-8:2005 灯具.第2部分:安全的特殊要求.第8节:手提灯

この規格は，250V以下の電源電圧で白熱電球又は蛍光ランプを使用し，手に持って使用するハンドランプ及び同様の移動灯器具(以下,ハンドランプという。)について規定する。

Luminaires -- Part 2: Particular requirements for safety -- Section 8: Handlamps

JIS C 8105-2-20:2005 灯具.第2-20部分:安全的特殊要求.照明链

この規格は，250Vを超えない入力電圧の屋内又は屋外用の白熱電球を，直列，並列又は直列，並列につなげたラィングチエーンに関する安全性要求事項について規定する。

Luminaires -- Part 2-20: Particular requirements -- Lighting chains

IEC 61347-2-12:2005 灯的控制装置.第2-12部分:放电灯(荧光灯除外)用直流或交流电子镇流器的特殊要求

本部分规定了直流或交流电子镇流器的一般要求和安全要求。电源包括交流电源为50Hz/ 60Hz、1 000 V以卜电源。此类镇流器是一种装行触发和稳定部件的转换器，这种转换器能在直流或 与电源频率不同的频率卜使放电灯工作。 与镇流器匹配的灯在IEC 60188《高压汞灯》，IEC 60192《低 压钠灯》，IEC 60662((高压钠灯》，IEC 611G7《金属卤化物灯》和其他普通照明光源标准巾均有规定，本 部分不包括荧光灯川镇流器及剧院和机动车辆用特种灯用的镇流器。

Lamp controlgear - Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)

SN/T 1588.1-2005 灯具发热试验用热试验光源

本标准规定了对GB 7000中主要检查灯头传导发热和对流的影响的热试验所用的热试验光源(H.T.S)的要求。附录A描述了本标准的起源和理念。 如没有H.T.S.光源，则可以使用替代H.T.S.(A.H.T.S.)光源。 GB 7000.1—2002的附录B给出了选择和制备这些光源的方法。 附录A中考虑了辐射试验光源R.T.S.。

Heat test source(H.T.S.)lamps for carrying out heating tests on luminaires

IEC 60598-2-11:2005 灯具.第2-11部分:特殊要求.鱼缸用灯具

This part of IEC 60598 specifies requirements for household aquarium luminaires for use with tungsten filament, tubular fluorescent or other discharge lamps on supply voltages not exceeding 1000 V.

Luminaires - Part 2-11: Particular requirements - Aquarium luminaires

JIS C 6191:2005 可调光源的试验方法

この規格は，光発振波長が400-1800nmの範囲で強度変調されていない連続光を出力する，光ファイバコネクタ用出力端子を備えた波長可変光源の試験方法について規定する。

Test methods of tunable light source

ANSI/UL 1598B-2005 预装荧光灯具用照明反射组件的补充要求

This bulletin proposes to correct the cross-references to align with the Second Edition of UL 1598.

Supplemental Requirements for Luminaire Reflector Kits for Installation on Previously Installed Fluorescent Luminaires

NF X90-011-2:2005 灯和照明.灯和灯具光度数据的测量和表示.第2部分:室内外工作场所用数据的表示

Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 2 : presentation of data for indoor and outdoor work places.

IEC 61549:2005 杂类灯

This International Standard specifies lamps, or information relevant to lamps, not given elsewhere in existing IEC lamp standards. It covers both safety and performance aspects. NOTE For reasons of flexibility the information in this loose-leaf publication is given in data sheet format.

Miscellaneous lamps

DLA A-A-59413 VALID NOTICE 1-2005 防水电子泛光灯(被替代:DLA MIL-F-11712 F 撤消通告 1,DLA MIL-F-11712 F(1),DLA MIL-F-11712 F,DLA MIL-F-11712 E(4),DLA MIL-F-11712 E INT AMD 3,DLA MIL-F-11712 E(2),DLA MIL-F-11712 E(1),DLA MIL-F-11712 E,DLA M)

The activities above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

FLOODLIGHT, ELECTRIC, WEATHERPROOF [Superseded: DLA MIL-F-11712 F CANC NOTICE 1, DLA MIL-F-11712 F (1), DLA MIL-F-11712 F, DLA MIL-F-11712 E (4), DLA MIL-F-11712 E INT AMD 3, DLA MIL-F-11712 E (2), DLA MIL-F-11712 E (1), DLA MIL-F-11712 E, DLA M

IEC 61995-1:2005 家用和类似用途灯具连接设备.第1部分:一般要求

This part of IEC 61995-1 applies to devices for the connection of luminaires (DCL) intended for household and similar purposes, for the electrical connection of fixed luminaires to final circuits rated at not more than 16 A without providing mechanical s

Devices for the connection of luminaires for household and similar purposes - Part 1: General requirements

DIN EN 13032-2:2005 灯和照明.灯和灯具光度数据的测量和表示.第2部分:室内和室外工作场所的数据描述

Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 2: Presentation of data for indoor and outdoor work places; German version EN 13032-2:2004

ANSI/IESNA RP-27.1-2005 电灯和电灯系统光生物学安全的推荐实施规程.一般要求

The evaluation and control of optical radiation hazards from electrically powered light sources (that emit in wavelength range of 200 nm - 3, 000 nm) except for LEDs and lasers.

Recommended Practice for Photobiological Safety for Lamps and Lamp Systems – General Requirements

ANSI C136.3-2005 道路照明设备.照明装置附件

Covers attachment features of luminaires used in roadway and area lighting equipment. The features covered apply to luminaires that are side- or post-top-mounted.

Roadway and Area Lighting Equipment - Luminaire Attachments

UL 1598-2004 照明装置

1.1 This Standard applies to luminaires for use in non-hazardous locations and that are intended for installation on branch circuits of 600 V nominal or less between conductors in accordance with the Canadian Electrical Code, Part I (CEC), CSA C22.1, with the U.S. National Electrical Code (NEC), ANSI/NFPA 70, and with the Mexican National Electrical Code, NOM-001-SEDE. 1.2 This Standard does not apply to luminaires covered by other standards. The luminaries not covered by this Standard include Amateur Movie Lights; Aquarium Lights; Cabinet Lights; Decorative Lighting Strings; Combination Fan/IR Lamps Used for Heating; Electric Signs; Exit Signs in the United States; Junction Boxes for Swimming Pool Fixtures; Lamp Adapters; Low-Level Path Marking and Lighting Systems in the United States; Low-Voltage Landscape Lighting as follows: For products intended for installation in Canada, landscape lighting systems that are 30 V nominal or less; and for products intended for installation in Mexico, low-voltage landscape lighting devices that are 24 V nominal or less. For products intended for installation in the United States, low-voltage landscape lighting devices that are of 15 V nominal or less; Low Voltage Lighting Fixtures for Use in Recreational Vehicles; Low Voltage Marine Lighting; Luminaires for Hazardous Locations; Luminaires for Recreational Vehicles; Marine Navigational Lights; Marine-Type Fixtures; Portable Electric Displays; Portable Hand Lamps; Portable Luminaires; Portable Sun/Heat Lamps; Self-Ballasted Lamps and Lamp Adapters; Stage and Studio Luminaires; Submersible Luminaires; Swimming Pools Luminaires; Temporary Lighting Strings; Therapeutic Lamps; Track Lighting Systems; Under-cabinet Lights in Canada and Cord-connected Under-cabinet Lights in the United States; and Unit Equipment for Emergency Lighting.

Luminaires

BS EN 50172:2004 紧急逃生照明系统

This European Standard specifies the provision of illumination of escape routes and safety signs in the event of failure of the normal supply, and specifies the minimum provision of such emergency lighting based on the size, type and usage of the premises. This standard relates to the provision of electric emergency escape lighting in all work places and premises open to the public. This European Standard does not cover private domestic premises but its provisions are applicable to common access routes within multi-storey dwellings. This European Standard is also applicable to standby lighting used as emergency escape lighting. There are emerging way guidance techniques that, when applied to escape routes in addition to conventional emergency lighting luminaires, can enhance its effectiveness in an emergency.

Emergency escape lighting systems

BS EN 60598-1:2004 灯具.一般要求和试验

This Part 1 of International Standard IEC 60598 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V. The requirements and related tests of this standard cover: classification, marking, mechanical construction and electrical construction. Each section of this Part 1 should be read in conjunction with this section 0 and with other relevant sections to which reference is made. Each section of IEC 60598-2 details requirements for a particular type of luminaire or group of luminaires on supply voltages not exceeding 1 000 V. These sections are published separately for ease of revision and additional sections will be added as and when a need for them is recognized. Attention is drawn to the fact that this Part 1 covers all aspects of safety (electrical, thermal and mechanical). The presentation of photometric data for luminaires is under consideration by the International Commission on Illumination (CIE) and is not, therefore, included in this Part 1. Requirements are included in this Part 1 for luminaires incorporating ignitors with nominal peak values of the voltage pulse not exceeding those of Table 11.3. The requirements apply to luminaires with ignitors built into ballasts and to luminaires with ignitors separate from ballasts. For luminaires with ignitors built into lamps, the requirements are under consideration. Requirements for semi-luminaires are included in this Part 1. In general this Part 1 covers safety requirements for luminaires. The object of this Part 1 is to provide a set of requirements and tests which are considered to be generally applicable to most types of luminaires and which can be called up as required by the detail specifications of IEC 60598-2. This Part 1 is thus not to be regarded as a specification in itself for any type of luminaire, and its provisions apply only to particular types of luminaires to the extent determined by the appropriate section of part 2. The sections of part 2, in making reference to any of the sections of Part 1, specify the extent to which that section is applicable and the order in which the tests are to be performed; they also include additional requirements as necessary. The order in which the sections of Part 1 are numbered has no particular significance as the order in which their provisions apply is determined for each type of luminaire or group of luminaires by the appropriate section of part 2. All sections of part 2 are self-contained and therefore do not contain references to other sections of part 2. Where the requirements of any of the sections of Part 1 are referred to in the sections of part 2 by the phrase "The requirements of section ... of IEC 60598-1 apply", this phrase is to be interpreted as meaning that all the requirements of that section of Part 1 apply except those which are clearly inapplicable to the particular type of luminaire covered by that section of part 2. For explosion proof luminaires, as covered by IEC 60079, the requirements of IEC 60598 (selecting the appropriate parts 2) are applied in addition to the requirements of IEC 60079. In the event of any conflict between IEC 60598 and IEC 60079, the requirements of IEC 60079 take priority. In accordance with IEC guidelines, new IEC standards are divided into those covering either safety or performance. In the lamp safety standards, "information for luminaire design" is given for the safe operation of lamps; this should be regarded as normative when testing luminaires to this standard. Attention is drawn to lamp performance standards which contain "information for luminaire design"; this should be followed for proper lamp operation; however, this standard does not require the testing of lamps performance as part of the type test approval for luminaires. Improvements in safety to take account of the state of the art technology are incorporated in the standards with revisions and amendments on an ongoing basis. Regional

Luminaires - General requirements and tests

BS EN 40-2:2004 灯柱.一般要求和尺寸

This document specifies the requirements and dimensions for lighting columns, brackets, base compartments, cableways and earthing terminals. It applies to post top columns not exceeding 20 m height for post top lanterns and columns with brackets not exceeding 18 m height for side entry lanterns. This Part does not attempt to restrict the actual appearance or shape of the column or bracket. The majority of lighting columns are normally of a stepped tubular, round, octagonal or polygonal cross-section. Lighting columns may be manufactured from materials other than those listed in the foreword (e.g. wood, plastic, cast iron) or in other forms (e.g. lattice and telescopic). This document specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under vehicle impact (passive safety) in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this document or available in separate documents.

Lighting columns - General requirements and dimensions

SANS 1041:2004 通用型管状荧光灯

Specifies requirements for tubular hot cathode fluorescent lamps for general lighting service, for operation with or without starters, at room temperature of 10 鳦 to 40 鳦.

Tubular fluorescent lamps for general service