K72 一般灯具 标准查询与下载

BS EN 40-3-1:2000 灯柱.设计和验证.特性负荷规范

This European Standard specifies design loads for lighting columns. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns. Special structural designs to permit the attachment of signs, overhead wires, etc. are not covered by this standard. The requirements for lighting columns made from materials other than concrete, steel or aluminium (for example wood, plastic and cast iron) are not specifically covered in this standard. This standard includes performance requirements for horizontal loads due to wind. Passive safety and the behaviour of a lighting column under the impact of a vehicle are not included; this group of lighting columns will have additional requirements (see prEN 40-2:1999).

Lighting columns - Design and verification - Specification for characteristic loads

IEC 60969:1988/AMD2:2000 普通照明用自镇流灯 性能要求 修改2

This standard is Self-ballasted lamps for general lighting services - Performance requirements; Amendment 2

Self-ballasted lamps for general lighting services - Performance requirements; Amendment 2

SANS 60598-2-19:1981 灯具．第2部分：特殊要求．第19节：通风式灯具（安全要求）

Specifies safety requirements for air-handling luminaires for use with a ventilation duct or ventilated space (plenum), for use with tubular fluorescent lamps on supply voltages not exceeding 1 000 V. Specifies only the safety aspects of air-handling lum

Luminaires Part 2: Particular requirements Section 19: Air-handling luminaires (safety requirements)

JIS C 8105-2-17:2000 灯具.第2部分:安全性特殊要求.第17节:舞台照明、电视、电影和摄影照明灯具(室外和室内用)

この規格は，電源電圧が1000V以下の白熱電球，蛍光ランプ及びその他の放電ランプを使用する屋内用及び屋外用の舞台?テレビ?映画?写真用スタジオ照明器具(スポット照明用及び投光照明用投光器を合む。)の要求事項を規定する。

Luminaries -- Part 2: Particular requirements for safety Section 17: Luminaires for stage lighting, television, film, and photographic (outdoor and indoor)

JIS C 8105-2-9:2000 灯具.第2部分:安全性特殊要求.第9节:摄影和电影照明灯具(非专业用)

Luminaires -- Part 2: Particular requirements for safety -- Section 9: Photo and film luminaires (non-professional)

JIS C 8105-2-8:2000 灯具.第2部分:安全性特殊要求.第8节:手提灯

Luminaires -- Part 2: Particular requirements for safety -- Section 8: Handlamps

JIS C 8105-2-7:2000 灯具.第2部分:安全性特殊要求.第7节:花园用便携灯具

Luminaires -- Part 2: Particular requirements for safety -- Section 7: Portable luminaires for garden use

JIS C 8105-2-6:2000 灯具.第2部分:安全性特殊要求.第6节:白炽灯用内装变压器或变换器的光源

この規格は，次に示す電源電圧及び出力電圧を有する変圧器及び電子式変圧器内蔵白熱灯器具の要求事項について規定する。

Luminaires -- Part 2: Particular requirements for safety -- Section 6: Luminaires with built-in transformers or converters for filament lamps

JIS C 7501:2000 普通照明用钨丝灯

この規格は，JIS C 7551-1:1999第2章安全要求事項に規定する一般照明用白熱電球の安全要求条件に適合する，次の条件を満たす一般照明用電球について規定する。

Tungsten filament lamps for general lighting purposes

JIS C 7523:2000 家用小型灯

この規格は，JIS C 7551-1:1999に規定する白熱電球類の安全規定に適合する，次の条件を満たす家庭用小形電球の性能について規定する。

Small lamps for household use

SANS 60598-2-7:1982 灯具．第2部分：特殊要求．第7节：庭园用便携式灯具

Specifies requirements for portable pedestal luminaires for use in places such as gardens and for portable luminaires for use in places such as flower beds, for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages

Luminaires Part 2: Particular requirements Section 7: Portable luminaires for garden use

SANS 60598-2-1:1979 灯具．第2部分：特殊要求．第1节：固定的一般用途灯具

Specifies requirements for fixed general purpose luminaires for use with tungsten filament, tubular fluorescent and other discharge lamps on supply voltages not exceeding 1 000 V.

Luminaires Part 2: Particular requirements Section 1: Fixed general purpose luminaires

DLA A-A-59413-2000 防水电子泛光灯(被替代:DLA MIL-F-11712 F 撤消通告 1,DLA MIL-F-11712 F(1),DLA MIL-F-11712 F,DLA MIL-F-11712 E(4),DLA MIL-F-11712 E INT AMD 3,DLA MIL-F-11712 E(2),DLA MIL-F-11712 E(1),DLA MIL-F-11712 E,DLA M)

This commercial item description (CID) covers weatherproof electric floodlights (luminaires) intended for illuminating recreational and industrial areas and for military utility lighting.

FLOODLIGHT, ELECTRIC, WEATHERPROOF [Superseded: DLA MIL-F-11712 F CANC NOTICE 1, DLA MIL-F-11712 F (1), DLA MIL-F-11712 F, DLA MIL-F-11712 E (4), DLA MIL-F-11712 E INT AMD 3, DLA MIL-F-11712 E (2), DLA MIL-F-11712 E (1), DLA MIL-F-11712 E, DLA M

ARMY MS18003 REV A VALID NOTICE 3-2000 3触头接线片式PAR 36型密封光束白炽前灯

MS 18003A remains inactive for new design, however, the document is valid for acthewhen needed.

LAMP INCANDESCENT-SEALED BEAM, PAR 36 HEADLAMP, 3 CONTACT LUG TYPE

ANSI/IESNA RP-8-2000 路灯的操作规程

Recommendations on the design of new, continuous fixed lighting systems for roadways, adjacent bikeways and pedestrian areas using one or a combination of methods; illuminance, luminane, and small target visibility.

Practice for Roadway Lighting

ASTM E2072-00(2002)e1 荧光安全标志标准规范

1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and other potentially dangerous objects. (see also Test Method E 2073, Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings, and Guide E 2030, Guide for Recommended Uses of Photoluminescent Safety Markings).1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings for detection in clear air under blackout conditions.1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

Standard Specification for Photoluminescent (Phosphorescent) Safety Markings

ASTM E2072-00 荧光安全标志标准规范

1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and other potentially dangerous objects. (see also Test Method E 2073, Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings, and Guide E 2030, Guide for Recommended Uses of Photoluminescent Safety Markings).1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings for detection in clear air under blackout conditions.1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

Standard Specification for Photoluminescent (Phosphorescent) Safety Markings

ASTM E2073-00 荧光标志可见光亮度的标准试验方法

1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.1.3 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings

WH/T 0204-1999 舞台灯具光学质量的测试与评价

The Test and Evaluation for Optics Quality of Stage Luminaries

IEC 61195:1999 双端荧光灯 安全规范

This International Standard specifies the safety requirements for double-capped fluorescent lamps for general lighting purposes of all groups having Fa6, Fa8, G5, G13, 2G13, R17d and W4.3x8.5d caps. It also specifies the method a manufacturer should use to show compliance with the requirements of this standard on the basis of whole production appraisal in association with his test records on finished products. This method can also be applied for certification purposes. Details of a batch test procedure which can be used to make limited assessment of batches are also given in this standard. NOTE - Compliance with this standard concerns only safety criteria and does not take into account the performance of double-capped fluorescent lamps for general lighting purposes with respect to luminous flux, colour, starting and operational characteristics. Readers are referred to IEC 60081 for such characteristics.

Double-capped fluorescent lamps - Safety specifications