K74 灯具附件 标准查询与下载

JIS C 8108:2008 荧光灯用镇流器

This Standard specifies magnetic type ballasts (hereafter referred to as the "bal- lasts") for operating the fluorescent lamps and the low pressure mercury germicidal discharge lamps (hereafter referred to as the "lamps"), specified in JIS C 7601 and JIS C 7605, respectively, which are with rated input voltage not exceeding 300 V a.c. (50 Hz, 60 Hz and 50/60 Hz) and rated secondary voltage not exceeding 1 000 V and are intended for use in general places.

Ballasts for fluorescent lamps

IEC 61184:2008 卡口灯座

This International Standard applies to bayonet lampholders B15d and B22d for connection of lamps and semi-luminaires to a supply voltage of 250 V. This standard also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard shall be observed and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. NOTE Where lampholders are used in luminaires, their maximum operating temperatures are specified in IEC 60598-1. B15 denotes the cap/holder fit as defined by IEC 60061-1, sheet 7004-11 and IEC 60061-2, sheet 7005-16 with the corresponding gauges. B22 denotes the cap/holder fit as defined by IEC 60061-1, sheet 7004-10 and IEC 60061-2, sheet 7005-10 with the correspondina gauges.

Bayonet lampholders

IEC 60838-1:2004/AMD1:2008 各类灯座.第1部分:一般要求和试验.修改件1

This amendment has been prepared by subcommittee 34B: Lamp caps and holders, of IEC technical committee 34: Lamps and related equipment. The text of this amendment is based on the following documents: FDIS Report on voting 34B/13841FDIS 34B/1400/RVD Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be ~ reconfirmed, ~ withdrawn, ~ replaced by a revised edition, or ~ amended.

Miscellaneous lampholders - Part 1: General requirements and tests; Amendment 1

IEC 60400:2008 管形荧光灯灯座和起动器座

This International Standard states the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starterholders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the starterholders. This standard covers independent lampholders and lampholders for building-in, used with tubular fluorescent lamps provided with caps as listed in Annex A, and independent starterholders and starterholders for building-in, used with starters in accordance with IEC 60155, intended for use in a.c. circuits where the working voltage does not exceed 1 000 V r.m.s. This standard also covers lampholders for single-capped tubular fluorescent lamps integrated in an outer shell and dome similar to Edison screw lampholders (e.g. for G23 and G24 capped lamps). Such lampholders are tested in accordance with the following clauses and subclauses of IEC 60238: 8.4; 8.5; 8.6; 9.3; 10.7; 11; 12.2; 12.5; 12.6; 12.7; 13; 15.3; 15.4; 15.5 and 15.9. This standard also covers lampholders which are integral with a luminaire or intended to be built into appliances. It covers the requirements for the lampholder only. For all other requirements, such as protection against electric shock in the area of the terminals, the requirements of the relevant appliance standard are to be observed and tested after building into the appropriate equipment, when that equipment is tested according to its own standard. Lampholders for use by luminaire manufacturers only are not for retail sale. This standard also applies, as far as is reasonable, to lampholders and starterholders other than the types explicitly mentioned above and to lamp connectors. Where the term "holder" is used in the standard, both lampholders and starterholders are intended.

Lampholders for tubular fluorescent lamps and starterholders

QB/T 2987-2008 空载输出电压超过1000V的管形放电灯用变压器(霓虹灯变压器).性能要求

本标准适用于输入和输出绕组分开的独立式、内装式单相变压器，它们采用50Hz/60Hz、1000V以下的交流电源，可向冷阴极管形灯（或此类灯的组合体）供电并使之稳定工作。此类变压器的空载额定对地输出电压大于1000V，但不超过10000V，适宜于照明、电气广告、灯光信号以及类似用途。

Transformers for tubular discharge lamps having a no-load output voltage exceeding 1000V(generally called neon-transformers).Performance requirements

NF C71-247-0/A1:2008 灯控制器.第1部分:总则和安全要求

Lamp controlgear - Part 1 : general and safety requirements.

DIN EN 60730-2-3:2008 家用和类似用途的自动电气控制装置.第2-3部分:管形荧光灯镇流器用热保护器的特殊要求

Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps (IEC 60730-2-3:2006, modified); German version EN 60730-2-3:2007

VC 9087-2009 灯控设备的强制性规范

This specification covers the safety requirements for lamp controlgear, excluding glow starters for tubular fluorescent lamps.

Compulsory specification for lamp controlgear

DIN EN 60927:2008 灯附件.起动装置(辉光起动器除外).性能要求

Auxiliaries for lamps - Starting devices (other than glow starters) - Performance requirements (IEC 60927:2007); German version EN 60927:2007

UL 1993 BULLETIN-2008 安全自镇流灯和灯适配器用UL标准

The following changes in requirements are being proposed: 1. This proposed Third Edition of the Standard for Self-Ballasted Lamps and Lamp Adapters, UL 1993, includes the following major changes from the previous edition: a) Expansion of the scope to include range of products intended to be covered by the standard; b) Added list of reference publications; c) Added and revised glossary definitions; d) Added new section containing general requirements covering basic assumptions and conventions; e) Relocated requirements for enclosures; f) Revised and relocated requirements covering polymeric materials including a change in the flammability requirement from V-1 to V-0; g) Revised and relocated requirements covering weight, size, and moment; h) Expanded requirements covering lamp bases and lampholders; i) Changes in requirements for printed circuit boards; j) Added requirements covering LED driver circuitry; k) Relocated requirements for power capacitors; l) Added requirements for lamp tests for fluorescent lamp light sources; m) Revised requirements for spacing of electrical parts; n) Added new requirements for accessibility of live parts; o) Added requirements for limits for LED light sources; p) Added requirements for non-discharge lamps; q) Revised requirements for environmental locations; r) Revised and relocated performance test requirements; s) Added temperature test requirements for devices with input rating greater than 50 W; t) Revised and relocated requirements for mold-stress relief conditioning; u) Added requirements for a deflection test; v) Revised humidity conditioning requirements; w) Added requirements for lamp fault conditions test; x) Added requirements for endof- lamp-life test for fluorescent lamp adapters; y) Added requirements for end-of-lamplife test for integrally self-ballasted fluorescent lamps; z) Added new section for test apparatus; aa) Revised marking section in order to provide clarification of requirements; ab) Miscellaneous editorial revisions such as relocating requirements throughout the standard, correcting references, and editorial clarifications.

UL Standard for Safety Self-Ballasted Lamps and Lamp Adapters

UL 496 BULLETIN-2008 安全灯座用UL标准

1 The requirements of this standard cover holders and connectors for electric lamps, including incandescent, fluorescent, and other electric-discharge-type lamps, rated as indicated in Clause 6, to be used in accordance with the Canadian Electrical Code (CEC), C22.1, Part I, and the National Electrical Code (NEC), ANSI/NFPA-70. 2 These requirements cover screw lampholders, including those intended to be mounted directly on an outlet-box, lampholders for special uses, lampholders for electric signs, and adapters that convert one lampholder size to another. 3 These requirements also cover holders for automatic starters used with fluorescent lamps. 4 These requirements also cover indicator lamps. 5 These requirements also cover lampholder inserts. 6 These requirements also cover naval-use lampholders. See Supplement sb. 7 These requirements do not cover fluorescent self-ballasted lamps and fluorescent lamp adapters covered in UL 1993. 8 These requirements do not cover seasonal-lighting lampholders, which are covered in UL 588 and CSA C22.2 No. 37. 9 These requirements do not cover electrode receptacles for use in gas-tube signs, which are covered in UL 879 and CSA C22.2 No. 34. 10 These requirements do not cover devices requiring a cross-bar, mounting strap, or other mounting means; such devices are considered to be luminaries. 11 These requirements do not cover nightlights, which are covered in UL 1786 and CSA C22.2 No. 12. This is the Twelfth Edition of ANSI/UL 496. It contains requirements from the Eleventh Edition of UL 496 and from the Eighth Edition of UL 542 and has been harmonized with the requirements of Canada.

UL Standard for Safety Lampholders

DIN EN 60061-2:2008 灯头、灯座及检验其互换性和安全性的量规.第2部分:灯座

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders (IEC 60061-2:1969 + supplements A:1970 to S:1997 + A18:1998 to A36:2007, modified); German version EN 60061-2:1993 + A1:1995 to A7:1997 + A18

NF C47-733*NF EN 60730-2-3:2008 家用及类似用途的自动电控装置.第2-3部分:管状荧光灯镇流器的热保护器的特殊要求

Automatic controls for household and similar use - Part 2-3 : particular requirements for thermal protectors for ballasts for tubular fluorescent lamps.

QB/T 2941-2008 高压钠灯用预置功率电感镇流器

本标准适用于不更换高压钠灯来改变灯功率用的预置功率电感式镇流器，这些镇流器使用50Hz、1000V以下交流电源。上述这类镇流器在额定输出功率时应首先满足GB/T 15042-2005的要求。 本标准应与GB 19510.10-2004和GB/T 15042-2005一起使用，本标准镇流器适用的高压钠灯应符合GB/T 13259的要求。

Preset-power reactor ballasts for high pressure sodium lamps

QB/T 2275-2008 镇流器型号命名方法

本标准规定了各种气体放电灯用电感式和电子式镇流器的型号命名方法。 本标准适用于各种气体放电式的电感式和电子式镇流器。

Type designations for ballasts

DIN EN 60061-3:2008 灯头、灯座及检验其安全性和互换性的量规.第3部分:量规

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges (IEC 60061-3:1969 + supplements A:1970 to U:1997 + A20:1998 to A38:2007, modified); German version EN 60061-3:1993 + A1:1995 to A7:1997 + A20:1998

QB/T 2061-2008 聚光灯泡及反射型聚光摄影灯泡

本标准规定了聚光灯泡及反射型聚光摄影灯泡（以下简称“灯泡”）的术语和定义、型号、主要尺寸和基本参数、技术要求、试验方法、检验规则及标志、包装、运输、贮存。 本标准适用于供电电压为220V、功率不大于3000W，应用于电影摄影、舞台配光和强光照明的聚光灯泡及反射型聚光摄影灯泡。 本标准应与GB 14196.1一起使用。

Spotlight and reflector photoflood lamp

DIN EN 60061-4:2008 灯头和灯座及其互换性和安全性的控制量规.第4部分:指南和通用信息(IEC 60061-4-1990 + 补充件 A:1992、B:1994、C:1994和 D:1995 + 修正的A5:1998 到 A11:2007)

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4: Guidelines and general information (IEC 60061-4:1990 + supplements A:1992, B:1994, C:1994, D:1995 + A5:1998 to A11:2007, modified); German version EN 600

NF C61-505/A11*NF EN 60061-4/A11:2008 可置换性和安全性的控制用带有量规的灯头和灯座.第4部分:指南和通用信息

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4 : guidelines and general information.

GOST R IEC 60838-1-2008 各式各样的灯座.第1部分:通用要求和试验方法

Miscellaneous lampholders. Part 1. General requirements and test methods