K74 灯具附件 标准查询与下载

IEC 60921:2006 管形荧光灯用镇流器.性能要求

This standard specifies performance requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with tubular fluorescent lamps with pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC 60081 and 60901. It applies to complete ballasts and their component parts such as resistors, transformers and capacitors. A.C. supplied electronic ballasts for tubular fluorescent lamps for high frequency operation specified in IEC 61347-2-3 are excluded from the scope of this standard. NOTE In some regions there are laws on EMC for luminaires. The controlgear also contributes to this EMC behaviour. See Bibliography for further references.

Ballasts for tubular fluorescent lamps - Performance requirements

IEC 61347-2-13:2006 灯控装置.第2-13部分:发光二极管交直流供电控制设施的特殊要求

This part of IEC 61347 specifies particular safety requirements for electronic controlgear for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and at an output frequency which can deviate from the supply frequency, associated with LED modules. Controlgear for LED modules specified in this standard are designed to provide constant voltage or current at SELV or SELV equivalent or higher voltages.Deviations from the pure voltage and current types do not exclude the gear from this standard. The annexes of IEC 61347-1 which are applicable according to this Part 2-13 and using the word “lamp” are understood to also comprise LED modules. Particular requirements for stationary independent SELV controlgear, which are part of the wiring in installations, are given in Annex I. Performance requirements will be covered by IEC 623841. Plug-in controlgear, being part of the luminaire, are covered as for built-in controlgear by the additional requirements of the luminaire standard.

Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgears for LED modules

IEC 60838-2-2:2006 杂类灯座 第2-2部分:特殊要求.发光二极管模块用连接器

Douilles diverses pour lampes - Partie 2-2: Regies particuiieres - Connecteurs pour modules DEL Miscellaneous lampholders - Part 2-2: Particular requirements - Connectors for LED-modules General Definitions General requirement

Miscellaneous lampholders - Part 2-2: Particular requirements - Connectors for LED modules

BS EN 60929:2006 管形荧光灯用交流供电电子镇流器规范.性能要求

This International Standard specifies performance requirements for electronic ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tubular fluorescent lamps as specified in IEC 60081 and IEC 60901 and other tubular fluorescent lamps for high frequency operation.

A.C. supplied electronic ballasts for tubular fluorescent lamps - Performance requirements

JIS C 7709-1 AMD 2 ERRATUM 1:2006 勘误

ERRATUM

JIS C 8117 AMD 1:2006 荧光灯用交流电子镇流器（修改件1）

この追補は，工業標準化法に基づき，日本工業標準調査会の審議を経て，経済産業大臣が改正したもので，これによって，JAS C 8117:1992は改正され，一部が置き換えられた。

AC supplied electronic ballasts for fluorescent lamps (Amendment 1)

IEC 61347-2-8:2006 灯控制装置.第2-8部分:荧光灯用镇流器的特殊要求

This part of IEC 61347 specifies safety requirements for ballasts, excluding resistance types, for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, associated with fluorescent lamps with or without pre-heated cathodes operated with or without a starter or starting device and having rated wattages, dimensions and characteristics as specified in IEC 60081 and 60901. This standard applies to complete ballasts and to their component parts such as reactors, transformers and capacitors. Particular requirements for thermally protected ballasts are given in annex B. Ballasts for conventional operation of lamps at mains frequency are covered, while a.c. supplied electronic ballasts for high frequency operation are excluded. These are specified in IEC 61347-2-3. Capacitors having a capacitance greater than 0,1 µF are covered by IEC 61048 and IEC 61049. Capacitors having a capacitance less than or equal to 0,1 µF are specified in IEC 60384-14. Performance requirements are the subject of IEC 60921.

Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps

JIS C 8122:2006 卡口灯座

この規格は，電源電圧250V以下に対するランブ及びセミルミネア接続用の差込みランプソケットB15d及びB22dに適用する。

Bayonet lampholders

JIS C 7709-1 AMD 2:2006 灯头、灯座及检验其互换性和安全性的量规.第1部分:灯头(修改件2)

この追補は，JIS C 7709-1:1997が，平成18年2月20日付けで改正されたことに伴って発行されたものである。

Lamp caps and holders together with gauges for the control of interchangeability and safety -- Part 1: Lamp caps (Amendment 2)

BS EN 60923:2005 电灯辅助设备.放电灯(管形荧光灯除外)镇流器.性能要求

This International Standard specifies performance requirements for ballasts for discharge lamps such as high-pressure mercury vapour, low-pressure sodium vapour, high-pressure sodium vapour and metal halide lamps. Clauses 12 through 15 each detail specific requirements for a particular type of ballast. This standard covers inductive type ballasts for use on a.c. supplies up to 1 000 V at 50 Hz to 60 Hz associated with discharge lamps, having rated wattage, dimensions and characteristics as specified in the relevant IEC lamp standards.

Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements

BS EN 61347-2-12:2005+A1:2010 灯控制装置.放电灯(荧光灯除外)用直流或交流电子镇流器的详细要求

This part of IEC 61347 specifies particular general and safety requirements for d.c. or a.c. supplied electronic ballasts. The supply comprises a.c. voltages up to 1000 V at 50 Hz/60 Hz. The type of ballast is an convertor that may contain igniting and stabilising elements for operation of a discharge lamp at d.c. or at a frequency that can deviate from the supply frequency. The lamps associated with the ballast are specified in IEC 60188 (High pressure mercury vapour lamps), IEC 60192 (Low pressure sodium vapour lamps), IEC 60662 (High pressure sodium vapour lamps), IEC 61167 (Metal halide lamps) and else for general purpose lighting. Ballasts for fluorescent lamps and for lamps for special applications like for theatre and for vehicles are excluded.

Lamp controlgear. Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)

BS EN 61347-2-12:2005 灯控制装置.第2-12部分:放电灯(荧光灯除外)用直流或交流电子镇流器的特殊要求

This part of IEC 61347 specifies particular general and safety requirements for d.c. or a.c. supplied electronic ballasts. The supply comprises a.c. voltages up to 1000 V at 50 Hz/60 Hz. The type of ballast is an convertor that may contain igniting and stabilising elements for operation of a discharge lamp at d.c. or at a frequency that can deviate from the supply frequency. The lamps associated with the ballast are specified in IEC 60188 (High pressure mercury vapour lamps), IEC 60192 (Low pressure sodium vapour lamps), IEC 60662 (High pressure sodium vapour lamps), IEC 61167 (Metal halide lamps) and else for general purpose lighting. Ballasts for fluorescent lamps and for lamps for special applications like for theatre and for vehicles are excluded.

Lamp controlgear - Part 2-12: Particular requirements for d.c. or a.c. supplied electronic ballasts for discharge lamps (excluding fluorescent lamps)

SANS 61995-1:2006 家用及类似用途的灯具连接用设备．第1部分：一般要求

Applies to devices for the connection of luminaires intended for household and similar purposes, for the electrical connection of fixed luminaires to final circuits rated at no more than 16 A without providing mechanical support for the luminaire. The ra

Devices for the connection of luminaires for household and similar purposes Part 1: General requirements

SANS 1012:2006 电灯调光器（公制单位）

Covers the requirements for electric light dimmers for incandescent lamps suitable for domestic use, intended for operation at voltages not exceeding 250 V r.m.s. to earth, and rated at not more than 3 kW. Does not cover dimmers for fluorescent lights.

Electric light dimmers (Metric units)

JIS C 8121-1 ERRATUM 1:2006 勘误

ERRATUM

DLA MS25216 REV B-2006 底部和头部的机身灯罩

The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http://assist.daps.dla.mil

COVER, TOP AND BOTTOM FUSELAGE LIGHTS

CSA C861-06-2006 集成镇流器紧凑型荧光灯和 第2版镇流器适配器的性能

Performance of self-ballasted compact fluorescent lamps and ballasted adapters Second Edition

Performance of integrated ballast compact fluorescent lamps and second edition ballast adapters

IEC 60929:2006 管形荧光灯用交流电子镇流器.性能要求

This International Standard specifies performance requirements for electronic ballasts for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tubular fluorescent lamps as specified in IEC 60081 and IEC 60901 and other tubular fluorescent lamps for high frequency operation. NOTE 1 Tests in this standard are type tests. Requirements for testing individual ballasts during production are not included. NOTE 2 There are regional standards regarding the regulation of mains current harmonics and immunity for endproducts like luminaires and independent controlgear. In a luminaire, the controlgear is dominant in this respect. Controlgear, together with other components, should comply with these standards.

AC-supplied electronic ballasts for tubular fluorescent lamps - Performance requirements

IEC 61347-2-1:2006 灯控装置.第2-1部分:起动装置(辉光起动器除外)的特殊要求

other than glow starters and ignitors) for fluorescent and other discharge lamps for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz which produce starting pulses not greater than 100 kV and which are used in combination with lamps and ballasts covered in IEC 60081, IEC 60188, IEC 60192, IEC 60662, IEC 60901, IEC 61167, IEC 61195, IEC 61199, IEC 61347-2-8 and IEC 61347-2-9. It does not apply to glow starters or starting devices which are incorporated in discharge lamps or which are manually operated. Preheat transformers for fluorescent lamps are covered by IEC 61347-2-8. NOTE Glow starters are dealt with in IEC 60155. Performance requirements are given in IEC 60927.

Lamp controlgear - Part 2-1: Particular requirements for starting devices (other than glow starters)

DLA MS27033 REV B NOTICE 3-2006 全向基座安装半埋入式飞行器信号识别灯

LIGHT, MARKER, AIRPORT, SEMIFLUSH, BASED MOUNTED,OMNIDIRECTIONAL

LIGHT, MARKER, AIRPORT, SEMIFLUSH, BASE MOUNTED, OMNIDIRECTIONAL