共找到 1112 条与 灯具附件 相关的标准,共 75 页
Lampholders for tubular fluorescent lamps and starterholders.
この規格は,予熱形蛍光ランプ用の互換性をもつグロースタータ(以下,スタータという。)の性能について規定する。
Glow-Starters for fluorescent lamps -- Performance specification
This specification covers a floodlight set that provides a minimum of 160,000 mean lumens mounted on an adjustable height floodlight mast.
FLOODLIGHT SET, ELECTRIC, PORTABLE
This amendment forms a part of MS26578B dated 17 September 1982 and is approved for use by all Departments and Agencies of the Department of Defense.
LIGHTS, MARKER, AIRPORT, SEMIFLUSH, BASE MOUNTED, BIDIRECTIONAL AND UNIDIRECTIONAL
This amendment forms a part of MS27033B dated 18 December 1964 and is approved for use by all Departments
LIGHT, MARKER, AIRPORT, SEMIFLUSH, BASE MOUNTED, OMNIDIRECTIONAL
This amendment forms a part of MS27280A dated 30 APRIL 1984 and is approved for use by all Departments and Agencies of the Department of Defense.
STAKE MOUNTING, AIRPORT MARKER LIGHT
This amendment forms a part of MS35422C dated 15 December 1993 and is approved for use by all Departments and Agencies of the Department of Defense.
LAMPHOLDER, LIGHT MARKER, CLEARANCE
This amendment has been prepared by IEC technical committee 72: Automatic controls for household use. Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of the base publication and its amendments will remain unchanged until 2002-10. At this date, the publication will be Report on voting 7214941 RV D reconfirmed; withdrawn; replaced by a revised edition, or amended.
Automatic Electrical Controls for Household and Similar Use Part 2: Particular Requirements for Thermal Protectors for Ballasts for Tubular Fluorescent Lamps
States the technical and dimensional requirements for lampholders for tubular fluorescent lamps and for starter-holders, and the methods of test to be used in determining the safety and the fit of the lamps in the lampholders and the starters in the star
Lampholders for tubular fluorescent lamps and starterholders
This standard is Lampholders for tubular fluorescent lamps and starterholders; Amendment 1.
Lampholders for tubular fluorescent lamps and starterholders; Amendment 1
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders; Amendment 26
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps; Amendment 29
Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges; Amendment 28
This European Standard gives the measurement method of the total input power for ballast-lamp circuits when operating with their associated fluorescent lamp(s). This standard applies to electrical ballast-lamp circuits comprised solely of the ballast and of the lamp(s). NOTE Requirements for testing individual ballasts during production are not included. It specifies the measurement method for the total input power for all ballasts sold for domestic and normal commercial purposes operating with the following fluorescent lamps: —linear lamps with power equal to or greater than 15 W; —single ended (compact) lamps with power equal to or greater than 18 W; —other general purpose lamps. This standard does not apply to: —ballasts which form an integral part of the lamp; —ballast-lamp circuits with capacitors connected in series; —controllable wire-wound magnetic ballasts; —luminaires, which rely on additional optical performance aspects.
Measurement method of total input power of ballast-lamp circuits
CCC-C-441C dated 12 November 1987, is inactive for new design and is no longer used,except for replacement purposes.
CLOTH, CORDUROY, COTTON [Use In Lieu Of: DLA CCC-C-00441 B]
Lamp controlgear - Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires (IEC 61347-2-11:2001); German version EN 61347-2-11:2001
This part of IEC 61347 specifies general and safety requirements for miscellaneous electronic circuits used with luminaires for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and/or d.c. supplies up to 250 V. This part does not apply to circuits or devices for which specific IEC standards are published. NOTE Examples of miscellaneous electronic circuits used with luminaires are - electronic ballast control circuits; - switching circuits used in association with daylight and/or presence sensors; - circuits to assist EMC performance; - intermittence and similar devices used with lighting chains; - earth leakage or open-circuit protective devices used with neon transformers.
Lamp controlgear - Particular requirements for miscellaneous electronic circuits used with luminaires
Proposed revisions to requirements for the Standard for Electric Sign Components, STP 879.
Standard for Electric Sign Components (revisions to STP 879)
This standard concerns the use of protective shields with Tungsten-Halogen Lamps.
Use of Protective Shields with Tungsten-Halogen Lamps - Cautionary Notice
This standard describes the essential design features and operating characteristics of reference ballasts for fluorescent lamps.
Reference Ballasts for Fluorescent Lamps
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号