K74 灯具附件 标准查询与下载

UL 879 BULLETINS-2002 电信号部件标准

Proposed revisions to requirements for the Standard for Electric Sign Components, STP 879.

Standard for Electric Sign Components

ANSI C82.13-2002 荧光灯和镇流器定义

This standard provides definitions of terms used in ANSI C78 and C82 series standards for fluorescent lamps and ballasts.

Definitions for Fluorescent Lamps and Ballasts

ANSI C82.2-2002 荧光灯镇流器的测量方法

This standard outlines the procedures to be followed and precautions to be observed in measuring and testing line frequency fluorescent lamp ballasts as specified.

Method of Measurement of Fluorescent Lamp Ballasts

UL 60730-2-3-2002 家用和类似用途电自动控制器.第2-3部分:管状荧光灯镇流器用热防护器的特殊要求

1 Scope This clause of Part 1 is replaced as follows 1 1 This standard applies to the evaluation of thermal protectors for ballasts for tubula r fluorescent lamps Requirements ceRceming the testing ofthe combination of ballast and thermal protector are given in IEC 920 This part applies to thermal protectors using NTC or PTC THERMISTORS，additional requirements for which are contalned in Annex J 1．1DV D2 Modification to the secondparagraph ofthe part2 Add“and UL 9357 to the end of the sentence 1 1 1 This standard applies to the inherent safety，to the OPERATING VALUES，OPERATING TIMES，and OPERATING SEQUENCES where such are associated with equipment safety and to the testing of thermal protectors used to protect ballasts for tubular lamps frOm overheating This standard applies to thermal protectors for ballasts within the scope of IEC 920 Thermal protectors covered by this standard may be suitable for ballasts for other discharge lamps Throughout this standard the word”protector'means"self-resetting THERMAL BALLAST PROTECTOR” 1．1．1DV D2Modificationtothe secondparagraph ofthepart2： Add“and UL 9357 to the end of the sentence 1 1 2 This standard is not applicable to other means used to protect ballasts 1 1 3 This standard does not apply to a manual device for opening the circuit 1 2 This standard applies to protectors for use with ballasts for use on a c supplies up to 690 V at 50 Hz 0r 60 HZ 1 3 This standard does not take into account the RESPONSE VALUE of an AUTOMATIC ACTION of a control if such a RESPONSE VALUE is dependent upon the method of mounting the control in the equipment Where a RESPONSE VALUE is of significant purpose for the protection of the USER，or su rroundings，the value defined in the appropriate household equipment standard or as determined by the manufactu rer shall apply 1．101DV DEAddition ofthefollowingtothepart2 In IEC terminology。“safety“is deftned as an acceptable level of risk．This is consistent with the intentions of UL requirements to reduce the risk of fi re，shock，or injury to persons． CopyrighL by Lhe Underw~iLers LaboraLories]nc Sun Sep 05 16：39：46 2004

UL Standard for Safety Automatic Electrical Controls for Household and Similar Use; Part 2: Particular Requirements for Thermal Protectors for Ballasts for Tubular Fluorescent Lamps (First Edition; Remains Current)

ANSI C82.4-2002 高亮度放电灯和低压钠灯用镇流器(多路供电类型)

This standard concerns Ballasts for High-Intensity Discharge and Low-Pressure Sodium Lamps (Multiple-Supply Type)

Ballasts for High-Intensity Discharge and Low-Pressure Sodium Lamps (Multiple-Supply Type)

SANS 60925:2001 用于直流供电的管形荧光灯用电子镇流器．性能技术要求

Specifies general performance requirements for electronic ballasts for use on d.c. supplies having rated voltages not exceeding 250 V, associated with tubular fluorescent lamps.

DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements

SANS 61347-2-11:2001 灯的控制装置．第2．11部分：与灯具同用的各种电子电路的特殊要求

Specifies general and safety requirements for miscellaneous electronic circuits used with luminaires for use on a.c. supplies up to 1 000 V at 50 Hz or 60 Hz and/or d.c. supplies up to 250 V.

Lamp controlgear Part 2-11: Particular requirements for miscellaneous electronic circuits used with luminaires

IEC 60061-2:1969/AMD24:2001 灯头、灯座及检验其安全性和互换性的量规 第2部分:灯座 修改24

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders; Amendment 24

IEC 60061-3:1969/AMD26:2001 灯头、灯座及检验其安全性和互换性的量规 第3部分:量规 修改26

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges; Amendment 26

IEC 60061-4:1990/AMD7:2001 灯头、灯座及检验其安全性和互换性的量规 第4部分:指南和一般资料 修改7

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 4: Guidelines and general information; Amendment 7

SANS 61347-2-4:2000 灯的控制装置．第2．4部分：一般照明用直流电子镇流器的特殊要求

Specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from transient and surge-free power sources, operated directly from batteries without charging equipment as used in leisure equipment, for example, cara

Lamp controlgear Part 2-4: Particular requirements for d.c supplied electronic ballasts for general lighting

SANS 61347-2-6:2000 灯的控制装置．第2．6部分：飞行器照明用直流电子镇流器的特殊要求

Specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges such as in aircraft.

Lamp controlgear Part 2-6: Particular requirements for d.c supplied electronic ballasts for aircraft lighting

SANS 61347-2-5:2000 灯的控制装置．第2．5部分：公交照明用直流电子镇流器的特殊要求

Specifies particular safety requirements for d.c. supplied electronic ballasts intended for operation from power sources likely to have attendant transients and surges, for example, for road and railway vehicles, tramcars and craft used for public transp

Lamp controlgear Part 2-5: Particular requirements for d.c supplied electronic ballasts for public transport lighting

BS EN 50272-2:2001 二次蓄电池和电池装置的安全性要求.固定电池

This European Standard applies to stationary secondary batteries and battery installations with a maximum voltage of DC 1500 V (nominal) and describes the principal measures for protections against hazards generated from: - electricity, - gas emission, - electrolyte. It provides requirements on safety aspects associated with the erection, use, inspection, maintenance and disposal. It covers lead-acid and NiCd batteries.

Safety requirements for secondary batteries and battery installations - Stationary batteries

IEC 60061-3:2001 灯头、灯座及检验其互换性和安全性的量规.第3部分:量规

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 3: Gauges

IEC 60730-2-3:2001 家用和类似用途的电自动控制器.第2-3部分:管形荧光灯镇流器的热防护器的特殊要求

This clause of Part 1 is replaced as follows: 1 This standard applies to the evaluation of thermal protectors for ballasts for tubular fluorescent lamps. This part applies to thermal protectors using NTC or PTC thermistors, additional requirements for which are contained in annex J. Requirements concerning the testing of the combination of ballast and thermal protector are given in IEC 60920. 1.1 This standard applies to the inherent safety, to the operating values, operating times, and operating sequences where such are associated with equipment safety and to the testing of thermal protectors used to protect ballasts for tubular lamps from overheating. This standard applies to thermal protectors for ballasts within the scope of IEC 60920. Thermal protectors covered by this standard may be suitable for ballasts for other discharge lamps. Throughout this standard the word "protector" means "self-resetting thermal ballast protector". 1.2 This standard is not applicable to other means used to protect ballasts. 1.3 This standard does not apply to a manual device for opening the circuit. 2 This standard applies to protectors for use with ballasts for use on a.c. supplies up to 690 V at 50 Hz or 60 Hz. 3 This standard does not take into account the response value of an automatic action of a control, if such a response value is dependent upon the method of mounting the control in the equipment. Where a response value is of significant purpose for the protection of the user, or surroundings, the value defined in the appropriate household equipment standard or as determined by the manufacturer shall apply.

Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps

IEC 60061-2:2001 灯头、灯座及检验其互换性和安全性的量规.第2部分:灯座

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 2: Lampholders

IEC 60925:2001 管状荧光灯用直流电子镇流器.性能要求

This standard specifies general performance requirements for electronic ballasts for use on d.c. supplies having rated voltages not exceeding 250 V, associated with fluorescent lamps complying with IEC 60081. It shall be read in conjunction with IEC 60924. Performance requirements for electronic ballasts for general, public transport and aircraft lighting are specified in Sections Two, Three and Four of this standard. NOTE 1 In order to obtain satisfactory performance of fluorescent lamps with d.c. supplied electronic ballasts, it is necessary that certain features of their designs be properly co-ordinated. It is essential, therefore, that specifica-tions for them be written in terms of measurement made against some common base-line of reference, which must be reasonably permanent and reproducible. NOTE 2 These conditions may be fulfilled by reference ballasts. Moreover, the testing of ballasts for fluorescent lamps will, in general, be made with reference lamps and, in particular, by comparing results obtained on such lamps with ballasts to be tested and with a reference ballast as specified in IEC 60921.

DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements

IEC 61047:2001 白炽灯用直流或交流电子降压转换器.性能要求

D.C. or A.C. supplied electronic step-down convertors for filament lamps - Performance requirements

IEC 60061-1:2001 灯头、灯座及检验其互换性和安全性的量规.第1部分:灯头

Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps