K84 蓄电能装置 标准查询与下载

BS EN 50342-2:2007 铅酸起动器蓄电池.第2部分:蓄电池尺寸和端子标记

This European Standard is applicable to lead-acid batteries used for starting, lighting and ignition of passenger automobiles and light commercial vehicles with a nominal voltage of 12 V. All batteries in accordance with this European Standard can be fastened to the vehicle either by means of the ledges around the case or by means of a hold-down device engaging with the lid.

Lead-acid starter batteries - Part 2: Dimensions of batteries and marking of terminals

UL 1642 BULLETIN-2008 锂电池UL安全性标准

1.1 These requirements cover primary (nonrechargeable) and secondary (rechargeable) lithium batteries for use as power sources in products. These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that convert chemical energy into electrical energy by an irreversible or reversible chemical reaction. 1.2 These requirements cover lithium batteries intended for use in technician-replaceable or user-replaceable applications. 1.3 These requirements are intended to reduce the risk of fire or explosion when lithium batteries are used in a product. The final acceptability of these batteries is dependent on their use in a complete product that complies with the requirements applicable to such product. 1.4 These requirements are also intended to reduce the risk of injury to persons due to fire or explosion when user-replaceable lithium batteries are removed from a product and discarded. 1.5 These requirements cover technician-replaceable lithium batteries that contain 5.0 g (0.18 ounce) or less of metallic lithium. A battery containing more than 5.0 g of lithium is judged on the basis of compliance with the requirements in this standard, insofar as they are applicable, and further examination and test to determine whether the battery is acceptable for its intended uses. 1.6 These requirements cover user-replaceable lithium batteries that contain 4.0 g (0.13 ounce) or less of metallic lithium with not more than 1.0 g (0.04 ounce) of metallic lithium in each electrochemical cell. A battery containing more than 4.0 g or a cell containing more than 1.0 g lithium may require further examination and test to determine whether the cells or batteries are acceptable for their intended uses. 1.7 These requirements do not cover the toxicity risk that may result from the ingestion of a lithium battery or its contents, nor the risk of injury to persons that may occur if a battery is cut open to provide access to the metallic lithium.

UL Standard for Safety Lithium Batteries

GOST R 53165-2008 汽车牵引机用启动铅酸性储存蓄电池.总规范

Lead-acid storage starter batteries for motor-tractors. General specifications

IEEE 1625-2008 多电池移动式计算装置用可再充电蓄电池

Rechargeable batteries for multi-cell mobile computing devices

ANSI/IEEE 1660:2008 循环设施中使用的固定式蓄电池应用和管理指南

This guide provides information on the differences between stationary standby and stationary cycling applications and appropriate battery management strategies in cycling operations.

Guide for Application and Management of Stationary Batteries Used in Cycling Service

JIS C 8714:2007 便携式电子设备使用的可移动型锂离子二次电池和电池组的安全试验

この規格は，携帯電子機器用のリチウムイオン蓄電池の単電池及び組電池の安全性試験について規定する。なお，この規格は，リチウムイオン蓄電池の形式試験，受渡試験などに適用する。

Safety tests for portable Lithium Ion secondary cells and batteries for use in portable electronic applications

ANSI/IEEE 1115a:2007 固定装置用镊镉电池的推荐实施规程.修改件1:外加规格极限

This amendment provides additional guidance on sizing margins that may be applied when nickel-cadmium batteries are used in stationary applications involving an element of charge-discharge cycling.

Recommended Practice for Sizing Nickel-Cadmium Batteries for Stationary Applications - Amendment 1: Additional Discussion on Sizing Margins

DIN EN 50272-4:2007 二次蓄电池和电池装置的安全要求.第4部分:便携装置用电池

Safety requirements for secondary batteries and battery installations - Part 4: Batteries for use in portable appliances; German version EN 50272-4:2007

BS DD IEC/TS 62257-8-1:2007 农村电气化用小型可再生能源和混合系统的建议.独立电气化系统用电池和电池管理系统的选择.适合发展中国家用的自动充满铅酸蓄电池的特殊案例

This Technical Specification proposes simple, cheap, comparative tests in order to discriminate easily, in a panel of automotive flooded lead-acid batteries the most acceptable model for PV Individual Electrification Systems. « It could be particularly useful for project implementers to test in laboratories of developing countries, the capability of locally made car or truck batteries to be used for their project. Furthermore battery testing specifications usually need too costly and too much sophisticated test equipment to be applied in developing countries laboratories. The tests provided in this document allow to assess batteries performances according to the general specification of the project (see IEC 62257-2) and batteries associated with their Battery Management System (BMS) in a short time and with common technical means. They can be performed locally, as close as possible to the real site operating conditions. The document provides also regulations and installation conditions to be complied with in order to ensure the life and proper operation of the installations as well as the safety of people living in proximity to the installation. This document is not a type approval standard. It is a technical specification to be used as guidelines and does not replace any existing IEC standard on batteries.

Recommendations for small renewable energy and hybrid systems for rural electrification - Selection of batteries and battery management systems for stand-alone electrification systems - Specific case of automotive flooded lead-acid batteries available in

IEEE 1189-2007 固定设备用调节阀铅酸(VRLA)蓄电池的选择指南

Describes methods for selecting the appropriate type of valve-regulated, immobilized-electrolyte, recombinant lead-acid battery for any of a variety of potential stationary float applications.

Guide for Selection of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Applications

ANSI/IEEE 1578:2007 固定蓄电池电解质溢出处理和管理的推荐实施规程

This recommended practice describes products, methods, and procedures relating to stationary batteries, battery electrolyte spill mechanisms, electrolyte containment and control methods, and fire fighting considerations.

Recommended Practice for Stationary Battery Electrolyte Spill Containment and Management

NF C58-272-4:2007 二次蓄电池和电池装置的安全要求.第4部分:便携装置用电池

Safety requirements for secondary batteries and battery installations - Part 4 : batteries for use in portable appliances.

DIN 43537:2007 铅酸蓄电池. 符合DIN EN 60254-2要求的E系列工业卡车装有的24V、36V、48V、72V、80V单电池的牵引用蓄电池.尺寸、重量和设计

Lead-acid batteries - Traction batteries 24 V, 36 V, 48 V, 72 V, 80 V with cells for industrial trucks of Series E according to DIN EN 60254-2 - Dimensions, weights, design

DIN 40540:2007 铅酸蓄电池. 爆炸性环境下(II组、目录2、目录3)运转的符合DIN EN 60254-2 要求的工业卡车装载的24V、36V、48V、80V单电池的牵引用蓄电池.尺寸、重量和设计

Lead-acid batteries - Traction batteries 24 V, 48 V, 80 V with cells for industrial trucks according to DIN EN 60254-2 operated in explosive atmospheres (Group II, Category 2 and Category 3) - Dimensions, weights, design

ANSI/IEEE 937:2007 光电(PV)系统用铅酸蓄电池组安装和维护实施规程

This recommended practice provides design considerations and procedures for storage, location, mounting, ventilation, assembly, and maintenance of lead-acid storage batteries for photovoltaic power systems. Safety precautions and instrumentation considerations are also included.

Recommended Practice for Installation and Maintenance of Lead-Acid Batteries for Photovoltaic (PV) Systems

ANSI/IEEE 1013:2007 单机光电(PV)系统用酸性铅蓄电池尺寸选定的推荐实施规程

This recommended practice provides a systematic approach for determining the appropriate energy capacity of a lead-acid battery to satisfy the energy requirements of the electrical loads of a stand-alone photovoltaic (PV) system. Since this capacity determination (sizing) assumes that no power is available from the array, the resulting battery capacity should be more than adequate to meet the PV system's load requirements during its normal operation.

Recommended Practice for Sizing Lead-Acid Batteries for Stand-Alone Photovoltaic (PV) Systems

DIN EN 61982-1:2007 电动道路车辆推进用二次电池.第1部分:试验参数

Secondary batteries for the propulsion of electric road vehicles - Part 1: Test parameters (IEC 61982-1:2006); German version EN 61982-1:2006

SANS 60095-1:2007 铅酸起动电池组．第1部分：一般要求和测试方法

Applicable to lead-acid batteries with a nominal voltage of 12 V, used primarily as a power source for the starting of internal combustion engines, lighting and for auxiliary equipment of internal combustion engine vehicles. These batteries are commonly

Lead-acid starter batteries Part 1: General requirements and methods of test

ANSI/IEEE 535:2006 核电站用1E类铅蓄电池的合格证明标准

Describes qualification methods for Class 1E vented lead acid batteries and racks to be used in nuclear power generating stations outside primary containment.

Standard for Qualification of Class 1E Lead Storage Batteries for Nuclear Power Generating Stations

IEC TS 62257-8-1:2007 农村电气化用小型可再生能源和混合系统的建议.第8-1部分:独立电气化系统用电池和电池管理系统的选择.发展中国家可采用的自动充满铅酸蓄电池的特殊案例

This Technical Specification proposes simple, cheap, comparative tests in order to discriminate easily, in a panel of automotive flooded lead-acid batteries the most acceptable model for PV Individual Electrification Systems. « It could be particularly useful for project implementers to test in laboratories of developing countries, the capability of locally made car or truck batteries to be used for their project. Furthermore battery testing specifications usually need too costly and too much sophisticated test equipment to be applied in developing countries laboratories. The tests provided in this document allow to assess batteries performances according to the general specification of the project (see IEC 62257-2) and batteries associated with their Battery Management System (BMS) in a short time and with common technical means. They can be performed locally, as close as possible to the real site operating conditions. The document provides also regulations and installation conditions to be complied with in order to ensure the life and proper operation of the installations as well as the safety of people living in proximity to the installation. This document is not a type approval standard. It is a technical specification to be used as guidelines and does not replace any existing IEC standard on batteries.

Recommendations for small renewable energy and hybrid systems for rural electrification - Part 8-1: Selection of batteries and battery management systems for stand-alone electrification systems - Specific case of automotive flooded lead-acid batteries ava