K84 蓄电能装置 标准查询与下载

ANSI/IEEE 1106:2005 固定设施用带泄漏口的镍镉蓄电池组的安装、维护、测试及更换的推荐实施规程

Provides recommendations for installation design and for installation, maintenance, and testing procedures that can be used to optimize the life and performance of vented nickel-cadmium batteries used in stationary standby applications. Also provides guidance for determining when the batteries should be replaced.

Recommended Practice for Installation, Maintenance, Testing, and Replacement of Vented Nickel-Cadmium Batteries for Stationary Applications

ANSI/IEEE 1491:2005 固定装置中选择和使用蓄电池监控设备的指南

Discusses operational parameters that may be observed by battery monitoring equipment used in stationary applications, and the relative value of such observations.

Guide for Selection and Use of Battery Monitoring Equipment in Stationary Applications

BS EN 61960:2004 包含碱性或其他非酸性电解质的二次电池和蓄电池.便携式设备用二次锂电池和蓄电池

This International Standard specifies performance tests, designations, markings, dimensions and other requirements for secondary lithium single cells and batteries for portable applications. The objective of this standard is to provide the purchasers and users of secondary lithium cells and batteries with a set of criteria with which they can judge the performance of secondary lithium cells and batteries offered by various manufacturers. This standard defines a minimum required level of performance and a standardized methodology by which testing is performed and the results of this testing reported to the user. Hence, users will be able to establish the viability of commercially available cells and batteries via the declared specification and thus be able to select the cell or battery best suited for their intended application. This standard covers secondary lithium cells and batteries with a range of chemistries. Each electrochemical couple has a characteristic voltage range over which it releases its electrical apacity, a characteristic nominal voltage and a characteristic end-of-discharge voltage during discharge. Users of secondary lithium cells and batteries are requested to consult the manufacturer for advice.

Secondary cells and batteries containing alkaline or other non-acid electrolytes - Secondary lithium cells and batteries for portable applications

BS EN 60254-1:2005 铅酸牵引用蓄电池.试验方法和一般要求

This part of IEC 60254 is applicable to lead-acid traction batteries used as power sources for electric propulsion. The tests defined are relevant to all traction battery applications which include road vehicles, locomotives, industrial trucks and mechanical handling equipments. Tests which may be used specifically to test batteries developed for use in vehicles such as light passenger vehicles, motor cycles, light commercial vehicles, etc. may be found in alternative standards e.g. IEC 61982-2.

Lead-acid traction batteries. General requirements and methods of test

NF C58-542/A1:2005 牵引用铅酸蓄电池.第2部分:电池和端子尺寸及电池的极性标记

Lead-acid traction batteries - Part 2 : dimensions of cells and terminals and marking of polarity on cells.

IEEE 1188-2005 发电站用阀调节铅酸(VRLA)蓄电池组的保养、试验和更新的推荐规程

Describes recommended maintenance and testing schedules, and testing procedures to optimize the life and performance of valve-regulated lead-acid (VRLA) batteries for stationary applications. Also provides guidance to determine when batteries should be replaced.

Recommended Practice for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Applications

UL 1642-2005 安全锂蓄电池组用UL标准.第4版

1.1 These requirements cover primary (nonrechargeable) and secondary (rechargeable) lithium batteries for use as power sources in products. These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that convert chemical energy into electrical energy by an irreversible or reversible chemical reaction. 1.2 These requirements cover lithium batteries intended for use in technician-replaceable or user-replaceable applications. 1.3 These requirements are intended to reduce the risk of fire or explosion when lithium batteries are used in a product. The final acceptability of these batteries is dependent on their use in a complete product that complies with the requirements applicable to such product. 1.4 These requirements are also intended to reduce the risk of injury to persons due to fire or explosion when user-replaceable lithium batteries are removed from a product and discarded. 1.5 These requirements cover technician-replaceable lithium batteries that contain 5.0 g (0.18 ounce) or less of metallic lithium. A battery containing more than 5.0 g of lithium is judged on the basis of compliance with the requirements in this standard, insofar as they are applicable, and further examination and test to determine whether the battery is acceptable for its intended uses. 1.6 These requirements cover user-replaceable lithium batteries that contain 4.0 g (0.13 ounce) or less of metallic lithium with not more than 1.0 g (0.04 ounce) of metallic lithium in each electrochemical cell. A battery containing more than 4.0 g or a cell containing more than 1.0 g lithium may require further examination and test to determine whether the cells or batteries are acceptable for their intended uses. 1.7 These requirements do not cover the toxicity risk that may result from the ingestion of a lithium battery or its contents, nor the risk of injury to persons that may occur if a battery is cut open to provide access to the metallic lithium.

UL Standard for Safety Lithium Batteries Fourth Edition; Reprint with Revisions Through and Including August 9, 2007

CSA C22.2 No.107.3-05-2005 不间断电源系统.第2版.UL 1778.第1次修订

Uninterruptible power systems Second Edition; UL 1778; Update No 1

Uninterruptible power systems Second Edition; Update No 1: February 2006

SAE J1495-2005 蓄电池阻燃通风系统的试验过程

This SAE Standard details procedures for testing lead-acid SLI (starting, lighting, and ignition), Heavy-Duty, EV (electric vehicle) and RV (recreational vehicle) batteries to determine the effectiveness of the battery venting system to retard the propagation of an externally ignited flame of battery gas into the interior of the battery where an explosive mixture is usually present. NOTE: At this time 1998, there is no known comparable ISO Standard.

Test Procedure for Battery Flame Retardant Venting Systems

SANS 1632-2:2005 蓄电池．第2部分：通风型固定铅酸电池和蓄电池

Specifies the characteristics of lead-acid cells and batteries of the vented type that are designed for service in a fixed location and that are permanently connected to the loads and to the d.c power supply.

Batteries Part 2: Vented-type stationary lead-acid cells and batteries

NF R13-503/A3:2005 铅酸起动蓄电池组.一般要求、试验和计数方法

Lead-acid starter batteries - General requirements, methods of test and numbering.

BS EN 62310-1:2005 静态传送系统(STS).一般和安全性要求

IEC 62310 consists of three parts and applies to free standing a.c. static transfer systems (STS) intended to ensure the continuity of power to load by automatically or manually controlled transfer, with or without interruption, from two or several a.c. independent sources. This part of IEC 62310 concerns general and safety requirements. See future IEC 62310-2 for electromagnetic compatibility (EMC) and futurelEC 62310-3 for the method of specifying performance and test requirements. This part of IEC 62310 is intended to reduce the risk of fire, electric shock, or injury to persons from installed equipment subject to installing, operating, and maintaining the equipment in the manner prescribed by the manufacturer. This part of IEC 62310 includes requirements for the switching elements, their control and protective elements, where applicable. This part of IEC 62310 also includes information for the overall integration of the STS and its accessories into the a.c. power distribution system. Components or devices necessary for the operation/control/protection/isolation (e.g. circuit-breakers, fuses, transformers, etc.) of a STS should comply with the requirements of the relevant IEC standards and are not covered by this part of IEC 62310. This standard applies to systems up to 1 000 V (a.c. value) which are intended to be used in single phase or phase-phase or three phase applications. This standard does not apply to: - devices for d.c. source switching; - static transfer system using only electromechanical switching devices intended to be used in emergency power systems with interruption of the supply to the load during transfer. This equipment is covered by IEC 60947-6-1; - the automatic switching devices integrated into UPS covered by IEC 62040 series. NOTE For STS intended to be used in vehicles, onboard ships or aircraft, in tropical countries, for emergency power systems (such as those used for health care facilities, fire fighting, emergency rescue, etc.), or on elevations greater than 1 000 m, different requirements may be necessary.

Static transfer systems (STS). General and safety requirements

NF C58-522:2005 飞行器用蓄电池组.第2部分:设计和制造要求

Aircraft batteries - Part 2 : design and construction requirements.

NF C58-521:2005 飞行器用蓄电池组.第1部分:一般试验要求和性能水平

Aircraft batteries - Part 1 : general test requirements and performance levels.

NF C58-523:2005 飞行器用蓄电池组.第3部分:产品规范及设计与性能说明(DDP)

Aircraft batteries - Part 3 : product specification and declaration of design and performance (DDP).

IEC 60254-1:2005 牵引用铅酸蓄电池组.第1部分:一般要求和试验方法

This part of IEC 60254 is applicable to lead acid traction batteries used as power sources for electric propulsion. The tests defined are relevant to all traction battery applications which include road vehicles, locomotives, industrial trucks and mechan

Lead-acid traction batteries - Part 1: General requirements and methods of tests

BS EN 60896-22:2004 固定式铅酸蓄电池组.阀门调节型.要求

This part of IEC 60896 applies to all stationary lead-acid cells and monobloc batteries of the valve regulated type for float charge applications, (i.e. permanently connected to a load and to a d.c. power supply), in a static location (i.e. not generally intended to be moved from place to place) and incorporated into stationary equipment or installed in battery rooms for use in telecom, uninterruptible power supply (UPS), utility switching, emergency power or similar applications. The objective of this part of IEC 60896 is to assist the specifier in the understanding of the purpose of each test contained within IEC 60896-21 and provide guidance on a suitable requirement that will result in the battery meeting the needs of a particular industry application and operational condition. This standard is used in conjunction with the common test methods described in IEC 60896-21 and is associated with all types and construction of valve regulated stationary lead-acid cells and monoblocs used in standby power applications. This part of IEC 60896 does not apply to lead-acid cells and batteries used for vehicle engine starting applications (IEC 60095 series), solar photovoltaic applications (IEC 61427), or general purpose applications (IEC 61056 series).

Stationary lead-acid batteries - Valve regulated types - Requirements

BS EN 60896-21:2004 固定式铅酸蓄电池组.阀门调节型.试验方法

This part of IEC 60896 applies to all stationary lead-acid cells and monobloc batteries of the valve regulated type for float charge applications, (i.e. permanently connected to a load and to a d.c. power supply), in a static location (i.e. not generally intended to be moved from place to place) and incorporated into stationary equipment or installed in battery rooms for use in telecom, uninterruptible power supply (UPS), utility switching, emergency power or similar applications. The objective of this part of IEC 60896 is to specify the methods of test for all types and construction of valve regulated stationary lead acid cells and monobloc batteries used in standby power applications. This part of IEC 60896 does not apply to lead-acid cells and monobloc batteries used for vehicle engine starting applications (IEC 60095 series), solar photovoltaic energy systems (IEC 61427), or general purpose applications (IEC 61056 series).

Stationary lead-acid batteries - Valve regulated types - Methods of test

SANS 1632-3:2005 蓄电池．第3部分：通风型棱镜形镍镉电池和蓄电池

Specifies the characteristics of prismatic nickel-cadmium cells and batteries of the vented type, that are designed for service either in a fixed location or in movable equipment and that are permanently connected to the loads and to the d.c. power suppl

Batteries Part 3: Vented-type prismatic nickel-cadmium cells and batteries

KS C IEC 60896-11:2005 固定式铅酸蓄电池组.第11部分:开孔透气型.通用要求和试验方法

이 규격은 고정 위치에서 사용되도록 고안되고(즉, 상습적으로 여기저기 옮겨지지 않음.) 영

Stationary lead-acid batteries－Part 11：Vented types－General requirements and methods of tests