L11 电容器 标准查询与下载

BS EN 60384-11-1:2008 电子设备用固定电容器 空白详细规范 聚对苯二甲酸乙二醇酯薄膜电介质金属箔直流固定电容器 评定等级EZ

1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-11, 1.4.2. 1.2 Dimensions Table 1 – Case size reference and dimensions 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Max. a.c. voltage (if applicable) Tangent of loss angle (tan δ) Insulation resistance Table 2 – Values of capacitance and of voltage related to case sizes

Fixed capacitors for use in electronic equipment. Blank detail specification. Fixed polyethylene- terephthalate film dielectric metal foil d.c. capacitors. Assessment level EZ

BS EN 60384-11:2008 电子设备用固定电容器.分规范.金属箔式聚对苯二甲酸乙二醇酯膜介质直流固定电容器

Fixed capacitors for use in electronic equipment - Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors

BS EN 60384-23:2005 电子设备用固定电容器.分规范.表面安装的金属化聚乙烯苯二甲酸盐膜介质直流(DC)固定电容器

Fixed capacitors for use in electronic equipment - Sectional specification - Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors

IEEE Std C37.43-2008 用于并联电容器的额定电压为1kV～38kV、高压冲击式熔断器、限流熔断器和组合型配电和功率级外部熔断器用规范

This standard establishes specifications for high-voltage (above 1000 V) distribution and power class expulsion, current-limiting, and combination-type external capacitor fuses and accessories, with rated voltages from 1 kV through 38 kV, for protecting shunt capacitors complying with IEEE Std 18™-20021 and NEMA CP 1-2000. All of these devices are intended for use on ac systems. These fuses may be used with capacitor units, groups of units, or entire banks and include specific capacitor line [group] and capacitor unit fuse types as follows: a) Current-limiting fuses b) Expulsion fuses IEEE Standard Specifications for High-Voltage Expulsion, Current-Limiting, and Combination-Type Distribution and Power Class External Fuses, with Rated Voltages from 1 kV through 38 kV, Used for the Protection of Shunt Capacitors 2 Copyright © 2008 IEEE. All rights reserved. c) Combination of current-limiting and expulsion fuses d) Fuse supports, fuse mountings, and accessories used with fuses of type a), type b), and type c) e) Current-limiting, expulsion, and combination-type capacitor fuses [type a), type b), and type c), respectively] used in fuse enclosure packages (FEPs)

Specifications for high-voltage expulsion, current-limiting, and combination-type distribution and power class external fuses, with rated voltages from 1 kV through 38 kV, used for the protection of shunt capacitors

IEC 60384-1:2008 电子设备用固定电容器.第1部分:总规范

This part of IEC 60384 is a generic specification and is applicable to fixed capacitors for use in electronic equipment. It establishes standard terms, inspection procedures and methods of test for use in sectional and detail specifications of electronic components for quality assessment or any other purpose.

Fixed capacitors for use in electronic equipment - Part 1: Generic specification

JIS C 5101-23-1:2008 电子设备用固定电容器.第23-1部分:空白详细规范.表面安装的金属化聚乙烯苯二甲酸盐薄膜介质直流固定电容器.评定水平EZ

この規格は，JIS C 5101-23を品種別通則とするプランク個別規格で，表面実装用固定メタライズドポリエチレソナフ夕レートフィルム直流コンデンサの評価水準EZ(以下。コンデンサという。)について規定する。

Fixed capacitors for use in electronic equipment -- Part 23-1: Blank detail specification -- Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors -- Assessment level EZ

JIS C 5101-23:2008 电子设备用固定电容器.第23部分:分规范.表面安装的金属化聚乙烯苯二甲酸盐膜介质直流固定电容器

この規格は，誘電体がボリエチレンナフタレートでその上にメタライズド電極をもつ電子機器用の表面実装用固定メタライズドポリエチレンナフタレートフィルム直流コンデンサ(以下，コンデンサという。)の品種別通則について規定する。

Fixed capacitors for use in electronic equipment -- Part 23: Sectional specification -- Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors

NF C93-112-4:2008 电子设备用固定电容器.第4部分:分规范.带有固体(MnO2)和非固体电解质的铝电解电容器

Fixed capacitors for use in electronic equipment - Part 4 : sectional specification - Aluminium electrolytic capacitors with solid (MnO2) and non-solid electrolyte.

NF C93-112-18:2008 电子设备用固定电容器.第18部分:分规范.带固体(MnO2)和非固体电解质的铝电解表面安装固定电容器

Fixed capacitors for use in electronic equipment - Part 18 : sectional specification - Fixed aluminium electrolytic surface mount capacitors with solid (MnO2) and non-solid electrolyte.

SJ 52283/3-2008 CAK45A型有可靠性指标的片式固体电解质钽电容器详细规范

本规范规定了CAK45A型有可靠性指标的片式固体电解质钽电容器的结构、外形尺寸、技术要求和试验方法。 本规范适用于模压封闭、烧结钽阴极、有极性的CAK45A型有可靠性指标的片式固体电解质钽电容器（以下简称电容器）。

Capacitors, solid electrolytic, tantalum, chip, established reliability, type CAK45A detail specification for

SJ 20989-2008 CA35N型组合式非固体电解质钽电容器详细规范

本规范规定了CA35N型组合式非固体电解质钽电容器（以下简称电容器）的结构、外型尺寸、技术要求和试验方法。 本规范适用于带绝缘层的金属外壳、金属盖板锡焊密封、有极性烧结钽阳极、径向（或轴向）引出、多个螺钉固定的组合式非固体电解质钽电容器。

Capacitors, electrolytic (nonsolid electrolyte), tantalum, combined, high capacitance type CA35N detail specification for

SJ 50733/6-2008 CAK38 型有可靠性指标的气密封非固体电解质全钽电容器详细规范

本规范规定了CAK38型有可靠性指标的非固体电解质钽电容器的结构、外形尺寸、技术要求和试验方法。 本规范适用于钽外壳气密封、烧结钽阳极、有极性的有可靠性指标的非固体电解质全钽电容器。

Capacitors, electrolytic (nonsolid electrolyte), tantalum, established reliability, type CAK38, detail specification for

SJ 52283/2-2008 CAK45L型有可靠性指标的片式固体电解质钽电容器详细规范

本规范规定了CAK45L型有可靠性指标的片式固体电解质钽电容器的结构、外形尺寸、技术要求和试验方法。 本规范适用于模压封装、烧结钽阳级、有极性的CAK45L型有可靠性指标的低等效串联电阻片式固体电解质钽电容器（以下简称电容器）。

Capacitors, solid electrolytic, tantalum, chip, established reliability, type CAK45L detail specification for

NF C93-112-3:2008 电子设备的固定电容器.第3部分:分规范:带有二氧化锰固体电解质的表面安装固定式钽电解电容器.

Fixed capacitors for use in electronic equipment - Part 3 : sectional specification : surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte.

BS EN 60384-3-1:2006 电子设备用固定电容器.第3-1部分:空白详细规范.带二氧化锰固体电解质的表面安装钽电解固定电容器.评估等级EZ

The text of document 40/1772/FDIS, future edition 2 of IEC 60384-3-1, prepared by IEC TC 40, Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60384-3-1 on 2006-11-01. The following dates were fixed: ?latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2007-08-01 ?latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-11-01 Annex ZA has been added by CENELEC.

Fixed capacitors for use in electronic equipment - Part 3-1:Blank detail specification - Surface mount fixed tantalum electrolytic capacitors with manganese dioxide solid electrolyte - Assessment level EZ

BS EN 60384-4-1:2007 电子设备用固定电容器.第4-1部分:空白详细规范.带非固体电解质的铝电解固定电容器.评估等级EZ

Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described. In the preparation of detail specifications, the contents of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification [1] The International Electrotechnical Commission or the National Standards Organization under whose authority the detail specification is drafted. [2] The IEC or National Standards number of the detail specification, data of issue and any further information required by the national system. [3] The number and issue number of the IEC or national generic specification. [4] The IEC number of the blank detail specification. Identification of the capacitor [5] A short description of the type of capacitor. [6] Information on typical construction (when applicable). NOTE When the capacitor is not designed for use in printed board applications, this is clearly stated in the detail specification in this position. [7] Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. [8] Application or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional specification. This implies that one blank detail specification may be used in combination with several assessment levels, provided the grouping of the tests does not change. [9] Reference data on the most important properties, to allow comparison between the various capacitor types.

Fixed capacitors for use in electronic equipment - Part 4-1: Blank detail specification — Fixed aluminium electrolytic capacitors with non-solid electrolyte — Assessment level EZ

BS EN 60384-4-2:2007 电子设备用固定电容器.第4-2部分:空白详细规范.固体(二氧化锰)电解质的铝电解固定电容器.评估等级EZ

Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described. In the preparation of detail specifications, the contents of 1.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification [1] The International Electrotechnical Commission or the National Standards Organization under whose authority the detail specification is drafted. [2] The IEC or National Standards number of the detail specification, data of issue and any further information required by the national system. [3] The number and issue number of the IEC or national generic specification. [4] The IEC number of the blank detail specification. Identification of the capacitor [5] A short description of the type of capacitor. [6] Information on typical construction (when applicable). NOTE When the capacitor is not designed for use in printed board applications, this is clearly stated in the detail specification in this position. [7] Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. [8] Application or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional specification. This implies that one blank detail specification may be used in combination with several assessment levels, provided the grouping of the tests does not change. [9] Reference data on the most important properties, to allow comparison between the various capacitor types.

Fixed capacitors for use in electronic equipment — Part 4-2: Blank detail specification — Fixed aluminium electrolytic capacitors with solid (MnO) electrolyte — Assessment level EZ

IEC 60915:2006/COR2:2008 电子设备用电容器和电阻器.轴端、衬套、单孔安装、衬套安装及轴驱动电子元件的优选尺寸.技术勘误2

This standard is Capacitors and resistors for use in electronic equipment - Preferred dimensions of shaft ends, bushes and for the mounting of single-hole, bush-mounted, shaft-operated electronic components; Corrigendum 2.

Capacitors and resistors for use in electronic equipment – Preferred dimensions of shaft ends, bushes and for the mounting of single-hole, bush-mounted, shaft-operated electronic components CORRIGENDUM 2 (Edition 2.0)

IEC 60384-11-1:2008 电子设备用固定电容器.第11-1部分:空白详细规范.金属箔式聚乙烯-对苯二甲酸酯膜介质直流固定电容器.评定等级EZ

1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-11, 1.4.2 1.2 Dimensions Table 1- Case size reference and dimensions 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rated capacitance Category voltage( if applicable) (see Table 2) Climatic category Rated temperature Max.a.c voltage (if applicable) Tangent of loss angle (tan δ) Insulation resistance Table 2- Values of capacitance and of voltage related to case sizes

Fixed capacitors for use in electronic equipment - Part 11-1: Blank detail specification - Fixed polyethylene terephthalate film dielectric metal foil d.c. capacitors - Assessment level EZ

IEC 60384-20-1:2008/COR1:2008 电子设备用固定电容器.第20-1部分:空白详细规范.金属化聚苯硫醚膜介质直流片式固定电容器.评定等级EZ.技术勘误1

This standard is Fixed capacitors for use in electronic equipment - Part 20-1: Blank detail specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ; Corrigendum 1.

Fixed capacitors for use in electronic equipment - Part 20-1: Blank detail specification - Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ; Corrigendum 1