L13 电阻器 标准查询与下载

DLA MIL-PRF-32159 SUPP 1-2004 空间级高性能最佳性 工业零OHM膜固定芯片电阻 常规

This supplement forms a part of MIL-PRF-32159 dated 1 July 2004.

RESISTORS, CHIP, FIXED, FILM, ZERO OHM, INDUSTRIAL, HIGH RELIABILITY, SPACE LEVEL, GENERAL SPECIFICATION FOR

DLA DSCC-DWG-90039 REV B-2004 热敏电阻

This drawing describes the requirements for a thermally sensitive resistor.

THERMISTOR, THERMALLY SENSITIVE RESISTOR

DLA DSCC-DWG-86097 REV E-2004 1瓦特装在面板上的可变电阻器

This drawing describes the requirements for a 1 watt, variable, panel mounted, resistor.

RESISTOR, VARIABLE, PANEL MOUNTED, 1 WATT

DLA MIL-PRF-39002 B-2004 半精绕线可变电阻器一般规格

This specification covers the general requirements for semi-precision, wirewound, variable, resistors having a resistance element of wire, wound on an insulated form shaped in an arc, so that a contact bears uniformly on the resistance element, when adjusted by a contact shaft. The electrical output (in terms of percent of applied voltage) is linear with respect to the angular position of the contact arm. These resistors are capable of full-load operation (when the maximum resistance is engaged) at a maximum ambient temperature of 85°C, and are suitable for continuous operation, when properly derated, at a maximum temperature of 135°C. These resistors have a tolerance of ±5 percent

RESISTORS, VARIABLE, WIREWOUND, SEMI-PRECISION, GENERAL SPECIFICATION FOR

DLA DSCC-DWG-87033 REV F-2004 单列直插式封装10引脚的电阻网络

This drawing describes the requirements for a 10 pin, single-in-line package (SIP), resistor network with a ±100 ppm/OC temperature coefficient

RESISTOR NETWORK, 10-PIN, SINGLE-IN-LINE PACKAGE (SIP)

DLA DSCC-DWG-96002 REV B-2004 固定薄膜低电感绝缘电阻器

This drawing describes the requirements for an insulated, fixed, film resistor which exhibits low inductance over a frequency range of 1 MHz to 30 MHz.

RESISTOR, FIXED, FILM, INSULATED, LOW INDUCTANCE

DLA MIL-PRF-12934 K SUPP 1-2004 精密绕线可变电阻的常规

MIL-PRF-12934/1C, dated 1 February 1999, has been reviewed and determined to be valid for use in acquisition

RESISTORS, VARIABLE, WIRE WOUND, PRECISION GENERAL SPECIFICATION FOR

DLA MIL-PRF-12934 K-2004 精密绕线可变电阻的常规

This specification covers the requirements for style RR0900, variable, wire-wound, precision resistor

RESISTORS, VARIABLE, WIRE WOUND, PRECISION GENERAL SPECIFICATION FOR

BS EN 60115-9-1:2004 电子设备用固定电阻器.空白详细规范.带可单独测量电阻器的固定表面安装电阻网络.评定等级EZ

Fixed resistors for use in electronic equipment —Part 9-1: Blank detail specification —Fixed surface mount resistor networks with individually measurable resistors —Assessment level EZ 1 General data 2 Inspection requirements

Fixed resistors for use in electronic equipment - Blank detail specification - Fixed surface mount resistor networks with individually measurable resistors - Assessment level EZ

BS EN 60115-9:2004 电子设备用固定电阻器.分规范.带可单独测量电阻器的表面安装固定电阻网络

This part of IEC 60115 is applicable to fixed surface mount resistor networks with individually measurable resistors for use in electronic equipment.

Fixed resistors for use in electronic equipment - Sectional specification - Fixed surface mount resistor networks with individually measurable resistors

BS EN 140400:2003 电子元器件质量评定协调系统.分规范.低功率表面安装的固定电阻器

This sectional specification prescribes the preferred values for characteristics and ratings and also the inspection requirements for fixed surface mount resistors of assessed quality. These resistors generally have metallised connecting pads and are intended to be mounted directly on to substrates, for example hybrid integrated circuits or printed boards. It selects from the generic specification, EN 60115-1, the appropriate methods of test to be used in detail specifications derived from this specification. Associated with this specification are one or more blank detail specifications each reference by an EN number. A blank detail specification which has been completed as specified in 1.2 of this specification forms a detail specification. Such detail specifications may be used for the grant of qualification approval to a resistor and for the performance of quality conformance inspection in accordance with the CECC system.

Harmonized system of quality assessment for electronic components - Sectional specification:Fixed low power surface mount (SMD) resistors

DLA DSCC-DWG-98021 REV A-2004 固定薄膜(绝缘)1/2瓦特电阻器

This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.

RESISTORS, FIXED, FILM (INSULATED), 1/2 WATT

DLA DSCC-DWG-98020 REV A-2004 固定薄膜(绝缘)1/8瓦特电阻器

This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.

RESISTORS, FIXED, FILM (INSULATED), 1/8 WATT

DLA DSCC-DWG-98022 REV A-2004 固定薄膜(绝缘)1瓦特电阻器

This drawing describes the requirements for insulated, fixed, film, resistors available in ±2 percent,±5 percent, and ±10 percent resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.

RESISTORS, FIXED, FILM (INSULATED), 1 WATT

DLA DSCC-DWG-88015 REV C-2004 8引脚单列直插式封装电阻网络

This drawing describes the requirements for an eight-pin, single inline package (SIP), resistor network.

RESISTOR NETWORK, 8-PIN, SINGLE INLINE PACKAGE

DLA A-A-59497 VALID NOTICE 1-2004 非精确或精确的绕线或没绕线可变电阻 常规

A-A-59497, dated 23 February 2000, has been reviewed and determined to be valid for use in acquisition

RESISTORS, VARIABLE, NONWIRE WOUND, WIRE WOUND, PRECISION, NONPRECISION, GENERAL REQUIREMENTS FOR

DLA QPL-83530-7-2004 电压敏感(压敏电阻器,金属氧化物)电阻器 一般规格

This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-PRF-83530. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

RESISTORS, VOLTAGE SENSITIVE (VARISTOR, METAL-OXIDE), GENERAL SPECIFICATION FOR

DLA MIL-PRF-18546 G-2004 (轧液槽安装)绕线固定电阻的常规

This specification covers the general requirements for power type, wire wound, fixed resistors which utilize the principal of heat dissipation through a metal mounting surface. The resistors have an initial resistance tolerance of ±1 percent and a resistance temperature characteristic range from 30 ppm/°C to 200 ppm/°C depending upon the resistance value. They are not suitable for application when the alternating current (ac) characteristics are of critical importance; however, provisions have been made to minimize the inductance.

RESISTORS, FIXED, WIRE-WOUND (POWER TYPE, CHASSIS MOUNTED), GENERAL SPECIFICATION FOR

DLA QPL-93-109-2004 线绕式(精确)固定电阻器.一般规格

This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL-R-93. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.

RESISTORS, FIXED, WIRE-WOUND (ACCURATE), GENERAL SPECIFICATION FOR

IEC 60115-9-1:2003 电子设备用固定电阻器.第9-1部分:空白详细规范:各电阻器可单独测量的表面安装固定电阻网络.评定水平EZ

Is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications.

Fixed resistors for use in electronic equipment - Part 9-1: Blank detail specification: Fixed surface mount resistor networks with individually measurable resistors; Assessment level EZ