L13 电阻器 标准查询与下载

IEC 60115-9:2003 电子设备用固定电阻器.第9部分:分规范:各电阻器可单独测量的表面安装固定电阻网络

Prescribes preferred ratings and characteristics and selects from IEC 60115-1, the appropriate Quality Assessment procedures, tests and measuring methods and gives general performance requirements for this type of resistor.

Fixed resistors for use in electronic equipment - Part 9: Sectional specification: Fixed surface mount resistor networks with individually measurable resistors

DLA DSCC-DWG-03022-2003 0603型最小值小于1欧姆的涂膜固定片状电阻器

This drawing describes the requirements for a 0.060 X 0.030 chip resistor of very low resistance values and a wide range of characteristics and tolerances.

RESISTOR, CHIP, FIXED, FILM, VALUES LESS THAN 1 OHM, STYLE 0603

DLA A-A-55088 B-2003 可熔的防爆电阻器

This (CID) covers the general requirements for flameproof, fusible resistors. These resistors act as a wire-wound resistor and a fuse, and are used in applications where precise control of fusing point and time lags are necessary. These resistors eliminate fire hazard and circuit board damage due to overheated components.

RESISTORS, FLAMEPROOF, FUSIBLE

DLA DSCC-DWG-03011-2003 0201型,0欧姆芯片涂膜固定电阻器

This drawing describes the requirements for a fixed, film, .020 X .010, zero-ohm, chip resistor.

RESISTOR, FIXED, FILM, CHIP, ZERO-OHM, STYLE 0201

DLA A-A-59714 A-2003 可重调熔线非直线型热敏电阻 一般要求

This CID covers the general requirements for a non-linear thermistor, commonly called resettable fuses. These resistors are polymeric positive temperature coefficient devices that offer a wider voltage, current and temperature range. Requirements for specific resistors are covered in the individual CID sheets. The resistors covered by this CID are intended for commercial/industrial applications.

RESISTORS, THERMAL, NON-LINEAR THERMISTOR (RESETTABLE FUSES) GENERAL REQUIREMENTS FOR

KS C IEC 60440:2003 电阻器非线性的测量方法

이 규격에 설명되어 있는 비선형성 측정 방법은 저항에 적용할 수 있다. 이 방법은 오직

Method of measurement of non－linearity in resistors

DLA DSCC-DWG-93079 REV C-2003 固定大量金属箔片状高精密1505型电阻器

This drawing describes the requirements for a bulk metal foil, ultra precision, chip resistor.

RESISTOR, FIXED, BULK METAL FOIL, CHIP, ULTRA PRECISION, STYLE 1505

DLA DSCC-DWG-95013 REV B-2003 固定薄膜片状0302型电阻器

This drawing describes the requirements for a 0.030 x 0.020 chip resistor.

RESISTOR, CHIP, FIXED, FILM, STYLE 0302

DLA DSCC-DWG-87014 REV H-2003 有无铅芯片座16引脚外部贴装的涂膜固定电阻网络

This drawing describes the requirements for a 16 pin, leadless chip carrier, resistor network. These networks are available in hermetically sealed and nonhermetically sealed packages.

RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 16 PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-87016 REV M-2003 有无铅芯片座20引脚外部贴装的涂膜固定电阻网络

This drawing describes the requirements for a 20 pin, leadless chip carrier, resistor network. These networks are available in hermetically sealed and nonhermetically sealed packages.

RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 20 PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-87017 REV J-2003 有无铅芯片座20引脚外部贴装的涂膜固定电阻网络

This drawing describes the requirements for a 20 pin, leadless chip carrier, resistor network. These networks are available only in nonhermetically sealed packages.

RESISTOR NETWORK, FIXED, FILM, SURFACE MOUNT, 20 PIN, LEADLESS CHIP CARRIER

DLA DSCC-DWG-87045 REV C-2003 双列直插式封装20引脚的涂膜固定电阻网络

This drawing describes the requirements for a 20 pin, hermetically sealed, dual-in-line package (DIP) resistor network.

RESISTOR NETWORK, FIXED, FILM, 20 PIN, HERMETICALLY SEALED, DUAL-IN-LINE PACKAGE (DIP)

DLA DSCC-DWG-95014 REV B-2003 固定薄膜片状0402型电阻器

This drawing describes the requirements for a 0.040 x 0.020 chip resistor.

RESISTOR, CHIP, FIXED, FILM, STYLE 0402

DLA DSCC-DWG-97004 REV B-2003 固定薄膜(绝缘)2瓦特电阻器

This drawing describes the requirements for insulated, fixed, film, resistor available in F (±1 percent), G (±2 percent), J (±5 percent), and K (±10 percent) resistance tolerances. These resistors are capable of full-load operation at an ambient temperature of 70OC.

RESISTORS, FIXED, FILM (INSULATED), 2 WATT

DLA MIL-PRF-29 B VALID NOTICE 1-2003 (高电压,插芯终端类型)外部计量定额电阻器

MIL-PRF-29B, dated 30 November 1998, has been reviewed and determined to be valid for use in acquisition

RESISTORS, FIXED, METER MULTIPLIER, EXTERNAL (HIGH VOLTAGE, FERRULE TERMINAL TYPE)

SJ 20857-2002 电阻箔复合材料规范

Specification for resistance foil composite material

SJ 51432/7-2002 RMK1005型有可靠性指标的片式膜.固定电阻器详细规范

Resistors,fixed,film,chip,established reliability,style RMK1005,detail specification for

BS EN 140401-802:2002 详细规范.低功率非线绕表面安装的固定电阻器.矩形.1和2级别的稳定性

Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors —Rectangular —Stability classes 1; 2 1 Characteristics and ratings 1.1 Dimensions and Ratings 1.2 Derating curve 1.3 Resistance range and tolerance on rated resistance 1.4 Variation of resistance with temperature and temperature rise 1.5 Climatic categories 1.6 Limits for change of resistance at tests 1.7 Non-linear properties 1.8 Marking, packaging and ordering designation 1.8.1 Component 1.8.2 Package 1.8.3 Packaging / Taping 1.8.4 Ordering information 1.9 Additional information (not for inspection purpose) 1.9.1 Storage 1.9.2 Mounting 1.9.3 Soldering process 1.9.4 Conductive glueing 1.9.5 Use of cleaning solvents 1.9.6 Pulse load capability 1.9.7 Variation of resistance value (drift) for lifetimes up to 200 000 h 1.9.8 Dissipation notes 1.9.9 Current noise 2 Quality assessment procedures 2.1 General 2.1.1 Zero defect approach 2.1.2 100%-Test 2.1.3 0Ω-Resistor 2.1.4 Certificate of Conformity (CoC) 2.1.5 Certified test records 2.1.6 Failure rate level (only version E) 2.2 Qualification Approval 2.2.1 Version A 2.2.2 Version E 2.3 Quality conformance inspection 2.3.1 Qualification approval according to EN 100114-2 2.3.2 Technology approval according to EN 100114-6 2.3.3 Non-conforming items Annex A (normative) Fixed sample size Qualification Approval and Quality Conformance Inspection test schedule for fixed low power surface mount (SMD) resistors Annex B (informative) Letter symbols Annex C (normative) Standards referred to in this specification

Detail Specification: Fixed low power non wire-wound surface mount(SMD) resistors - Rectangular - Stability classes 1; 2

BS EN 140401-801:2002 详细规范.低功率非线绕表面安装电阻器.矩形. 0.1、0.25、0.5和1级别的稳定性

Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors —Rectangular —Stability classes 0,1; 0,25; 0,5; 1 1 Characteristics and ratings 1.1 Dimensions and Ratings 1.2 Derating curve 1.3 Resistance range and tolerance on rated resistance 1.4 Variation of resistance with temperature and temperature rise 1.5 Climatic categories 1.6 Limits for change of resistance at tests 1.7 Non-linear properties 1.8 Marking, packaging and ordering designation 1.8.1 Component 1.8.2 Package 1.8.3 Packaging / Taping 1.8.4 Ordering information 1.9 Additional information (not for inspection pin-pose) 1.9.1 Storage 1.9.2 Mounting 1.9.3 Soldering process 1.9.4 Conductive glueing 1.9.5 Use of cleaning solvents 1.9.6 Pulse load capability 1.9.7 Variation of resistance value (drift) for lifetimes up to 200 000 h 1.9.8 Dissipation notes 1.9.9 Current noise 1.9.10 Temperature range extension 2 Quality assessment procedures 2.1 General 2.1.1 Zero defect approach 2.1.2 100%-Test 2.1.3 0Ω-Resistor 2.1.4 Certificate of Conformity (CoC) 2.1.5 Certified test records 2.1.6 Failure rate level (only version E) 2.2 Qualification Approval 2.2.1 Version A 2.2.2 Version E 2.3 Quality conformance inspection 2.3.1 Qualification approval according to EN 100114-2 2.3.2 Technology approval according to EN 100114-6 2.3.3 Non-conforming items Annex A (normative) Fixed sample size Qualification Approval and Quality Conformance Inspection test schedule for fixed low power surface mount (SMD) resistors Annex B (informative) Letter symbols and abbreviations Annex C (normative) Standards referred to in this specification

Detail specification - Fixed low power non wire-wound surface mount (SMD) resistors - Rectangular - Stability classes 0,1; 0,25; 0,5 ; 1

BS EN 140401-803:2002 详细规范.低功率非线绕表面安装的固定电阻器.矩形.0.05、0.1、0.25、0.5、1和2级别的稳定性

Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors —Cylindrical —Stability classes 0,05; 0,1; 0,25; 0,5; 1; 2 1 Characteristics and ratings 1.1 Dimensions and Ratings 1.2 Derating curve 1.3 Resistance range and tolerance on rated resistance 1.4 Variation of resistance with temperature and temperature rise 1.5 Climatic categories 1.6 Limits for change of resistance at tests 1.7 Non-linear properties 1.8 Marking, packaging and ordering designation 1.8.1 Component 1.8.2 Package 1.8.3 Packaging / Taping 1.8.4 Ordering information 1.9 Additional information (not for inspection purpose) 1.9.1 Storage 1.9.2 Mounting 1.9.3 Soldering process 1.9.4 Conductive glueing 1.9.5 Use of cleaning solvents 1.9.6 Pulse load capability 1.9.7 Variation of resistance value (drift) for lifetimes up to 200 000 h 1.9.8 Dissipation notes 1.9.9 Current noise 2 Quality assessment procedures 2.1 General 2.1.1 Zero defect approach 2.1.2 100%-Test 2.1.3 0Ω -Resistor 2.1.4 Certificate of Conformity (CoC) 2.1.5 Certified test records 2.1.6 Failure rate level (only version E) 2.2 Qualification Approval 2.2.1 Version A 2.2.2 Version E 2.3 Quality conformance inspection 2.3.1 Qualification approval according to EN 100114-2 2.3.2 Technology approval according to EN 100114-6 2.3.3 Non-conforming items Annex A (normative) Fixed sample size Qualification Approval and Quality Conformance Inspection test schedule for fixed low power surface mounting (SMD) resistors Annex B (informative) Letter symbols and abbreviations Annex C (normative) Standards referred to in this specification

Detail specification - Fixed low power non wire-wound surface mount (SMD) resistors - Cylindrical - Stability classes 0,05; 0,1; 0 ,25; 0,5; 1; 2