L13 电阻器 标准查询与下载

CECC 40 401-801-1998 细节规格:固定的低能力非线绕表面装备(碎片) 电阻器 0,25.0,5.1.2 被替代EN 140401-801:2003

Detail Specification: Fixed Low Power Non-Wire Wound Surface Mounting (SMD) Resistors Thin Film, Rectangular Stability Classes 0,1; 0,5; 1 Superseded by EN 140401-801:2003

Detail Specification: Fixed Low Power Non-Wire Wound Surface Mounting (SMD) Resistors Thin Film, Rectangular Stability Classes 0,1; 0,5; 1 [Superseded By: CECC EN 140401-801]

SJ 52828/1-1998 RXG9功率型线绕固定电阻器详细规范

Resistors,fixed,wire-wound,power,style RXG9,detail specification for

SJ 50920/1-1998 RN2161型膜固定电阻网络详细规范

Resistor network,fixed,film,style RN2161,detail specification for

JIS C 5201-1:1998 电子设备用固定电阻器.第1部分:一般规范

この規格は，電子機器用固定抵抗器の品目別通則で，電子機器用固定抵抗器(以下.祇抗器という。)について規定する。

Fixed resistors for use in electronic equipment Part 1: Generic specification

ASTM F390-98(2003) 用共线四探针法对金属薄膜的薄膜耐力的试验方法

1.1 This test method covers the measurement of the sheet resistance of metallic thin films with a collinear four-probe array. It is intended for use with rectangular metallic films between 0.01 and 100 [mu]m thick, formed by deposition of a material or by a thinning process and supported by an insulating substrate, in the sheet resistance range from 10 to 10 [omega]/[open-box] (see 3.1.3). 1.2 This test method is suitable for referee measurement purposes as well as for routine acceptance measurements. 1.3 The values stated in Si units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Sheet Resistance of Thin Metallic Films With a Collinear Four-Probe Array

IPC TM-650 5.5.2.3-1998 试验方法2.5.17体积电阻率和外部电阻

This test describes a procedure which may be conducted to determine if a printed wiring board is constructed to withstand the dynamic vibrational stresses that may be encountered during field service. This test method provides specific parameters for one application in order to present the proper procedures. Specific test conditions must be agreed upon by the customer and the vendor.

Test Method 2.5.17 Volume Resistivity and Surface Resistance

DLA MIL-PRF-29 B-1998 (高电压,插芯终端类型)外部计量定额电阻器

This specification covers the requirements for high-voltage, external, meter-multiplier, fixed resistors of the ferrule-terminal type for use with direct-current (dc) instruments drawing 1 milliampere at full-scale deflection.

RESISTORS, FIXED, METER MULTIPLIER, EXTERNAL (HIGH VOLTAGE, FERRULE TERMINAL TYPE)

KS C 2611-1997 电阻用漆包线·油性漆包线

이 규격은 KS D 5581, KS D 5582 및 KS C 2514에서 규정하는 전기 저

Enamelled wires and oleo -resinous enamelled silk covered wires for electrical resistance use

JB/T 8622-1997 工业铂热电阻技术条件及分度表

本标准适用于－200℃～＋850℃整个或部分温度范围的工业铂热电阻。

Technical specification and reference table for industrial platinum thermal resistance

BS EN 140400:1997 电子元器件质量评定协调体系.分规范:固定的低功率表面安装电阻器

Prescribes the preferred values for characteristics and ratings, and also inspection requirements.

Harmonized system of quality assessment for electronic components - Sectional specification:fixed low power surface mounting (SMD) resistors

BS EN 140100:1997 电子元器件质量评定协调体系.分规范:低压非线绕固定电阻器

Prescribes the ratings, characteristics, inspection requirements and test severities for non-wirewound resistors with a dissipation not greater than 4.0 W.

Harmonized system of quality assessment for electronic components - Sectional specification: fixed low power non-wire wound resistors

CECC 40 401-803-1997 细节规格:固定的低能力非线绕表面装备(碎片) 电阻器 0,25.0,5.1.2 被替代EN 140401-801:2003

Detail Specification: Fixed Low Power Non-Wirewound Surface Mounting (SMD) Resistors Cylindrical Stability Classes 0,25; 0,5; 1; 2 Superseded by CENELEC EN 140401-803: 2002

Detail Specification: Fixed Low Power Non-Wirewound Surface Mounting (SMD) Resistors Cylindrical Stability Classes 0,25; 0,5; 1; 2

DIN EN 140203:1997 空白详细规范.大功率固定电阻(评定等级 H)

The document is a supplementary document of the sectional specification for fixed power resisitors (Assessment level H) and contains requirements for style and layout and minimum content of the detail specification.

Blank detail specification: Fixed power resistors (Assessment level H); German version EN 140203:1996

NF C93-858:1997 光缆用电介质强度构件

Dielectric strength member used in optical fibre cables.

JIS C 1604:1997 电阻式温度计传感器

この規格は，温度測定に使用する白金測温抵抗体(以下,測温抵抗体という。)について規定する。

Resistance thermometer sensors

DLA DSCC-DWG-89040 REV B-1997 固定线绕表面安装功率性(2.5瓦特)电阻器

This drawing describes the requirements for a surface mounted, fixed, power type, wire wound and low value shunt wire resistor.

RESISTOR, FIXED, WIRE WOUND, SURFACE MOUNT, POWER TYPE (2.5 WATTS)

BS EN 140104:1996 电子元器件质量评定协调体系.空白详细规范:固定低功率非线绕电阻器(评定等级SB和SC)

Lists the ratings, characteristics and inspection requirements which shall be included as mandatory requirements in any detail specification for this type of resistor.

Harmonized system of quality assessment for electronic components - Blank detail specification: fixed low power non-wirewound resistors (Assessment levels SB and SC)

BS EN 140102:1996 电子元器件质量评定协调体系.空白详细规范:固定低功率非线绕电阻器(评定等级M)

Blank detail specification: Fixed low power non-wirewound resistors (Assessment levelM) Committees responsible National foreword Foreword Text of EN 140102

Harmonized system of quality assessment for electronic components - Blank detail specification: fixed low power non-wirewound resistors (assessment level M)

BS EN 140103:1996 电子元器件质量评定协调体系.空白详细规范:固定低功率非线绕电阻器(评定等级P)

Lists the ratings, characteristics and inspection requirements which shall be included as mandatory requirements in any detail specification for this type of resistor.

Harmonized system of quality assessment for electronic components - Blank detail specification - Fixed low power non-wirewound resistors (Assessment level P)

SJ 51929/3-1996 RJ25型高稳定金属膜固定电阻器详细规范

Resistors,fixed,metal film,high stability,style RJ25,Detail specification for