L17 电感器、变压器 标准查询与下载

IEC 60186/AMD1:1988 电压互感器.IEC 60186-87标准的第1次修订

Voltage transformers; amendment No. 1 to IEC 60186:1987

DLA MS16476 REV A VALID NOTICE 1-1988 TF4SX04EB214型(反应堆)电感器

The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.

INDUCTOR, (REACTOR) TYPE TF4SX04EB214

BS 9925 Pt.02.01 and Pt.02.02:1988 电子元器件用质量评估协调体系.通信用电感器和变压器磁心.第2部分:空白详细规范:宽带变压器用磁氧化物磁心.第1节和第2节:A级和B级评估

This specification lists the ratings, characteristics, inspection requirements and additional information for magnetic oxide cores for broad-baan transformers at assessment levels A and B, which are to be included as the minimum mandatory requirements in any detail specification derived from the correspending sectional specification: IEC Publication 723-3: Inductor and Transformer Cores for Telecommunications. Part 3: Sectional Specification: Magnetic Oxide Cores for Broad-band Transformers. which should also be referred to for guidance on optional requirements.

Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Blank detail specification: magnetic oxide cores for broad-band transformers - Assessment levels A and B

SJ/Z 2921-1988 开关电源变压器计算方法

本标准规定了脉宽调制型开关稳压电源中功率输出变压器的计算方法。 本标准适用于脉宽调制型开关电源变压器的设计计算。

Calculating methods for transformers for switched mode power supplies

JIS C 1736:1988 计量仪器用互感器

Instrument transformers for metering service

JIS C 1731:1988 计量仪器用变压器(标准和一般计量仪器)

Instrument transformers for testing purpose and used with general instrument

NF C52-201:1988 变压器.控制和通信回路用变压器.特性和尺寸

ELECTRIC TRANSFORMERS. TRANSFORMERS FOR SUPPLY OF CONTROL AND SIGNALLING CIRCUITS. PARTICULAR REQUIREMENTS AND DIMENSIONS.

IEC 60938-2:1988 抑制无线电干扰用固定电感器.第2部分:分规范:试验方法的选择及一般要求

Fixed inductors for radio interference suppression. Part 2: Sectional specification - Selection of methods of test and general requirements

BS 9925-02.0:1987 电子元器件用质量评估协调体系.通信用电感器和变压器磁心.第2部分:分规范:宽带变压器用磁氧化物磁心

Characteristics, ratings and inspection requirements. Selects from the generic specification BS 9925-0, and from the basic specification BS 5938-1, the appropriate methods of test to be used in detail specifications derived from it, in accordance with the appropriate blank detail specification.

Harmonized system of quality assessment for electronic components - Inductor and transformer cores for telecommunications - Sectional specification: magnetic oxide cores for broad-band transformers

BS 6600-1:1987 通信与电子设备用变压器与电感器的外形尺寸.第1部分:使用YEI-1叠片的变压器和电感器的外形尺寸规格

Outline dimensions and fixing centres for transformers and inductors according to BS 6554-1, for bracket, U-clamp, printed wiring board and frame styles of mounting. The frame style, which is an addition to the text of IEC 60852-1:1986, is preferred in the UK to the bracket style, which has the same outline dimensions.

Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Specification for the outline dimensions of transformers and inductors using YEI-1 laminations

NF C01-321:1987 电工词汇.３２１章.仪表用互感器

Electrotechnical vocabulary. Chapter 321 : instrument transformers.

BS 6811-1.1:1987 绕组线.基本尺寸.第1部分:圆绕组线导体直径规范

Irrespective of conductor material and type of insulation.

Winding wires - Basic dimensions - Specification for diameters of conductors for round winding wires

IEEE 390-1987 脉冲变压器

This standard pertains to pulse transformers for use in electronic equipment. For the various types of these transformers, the peak power transmitted ranges from a few milliwatts to kilowatts; and the peak voltage transmitted ranges from a few volts to many kilovolts. The purpose of this standard is to provide a common ground between electronic system engineers and pulse transformer design engineers.

Standard for Pulse Transformers Revision of ANSI/IEEE Std 390-1975 and IEEE Std 391-1976

IEC 60186:1987 电压互感器

Voltage transformers

AS 1675:1986 电流变压器.测量和保护

Specifies requirements for the designation, rating, performance, marking, and testing of current transformers (CTs). Covers aspects common to all CTs (Section 1) and specific requirements for Class M and Class ME measurement CTs (Section 2) and for Class

Current transformers - Measurement and protection

BS 9753:1986 电子设备性能鉴定用的经质量评定的可变射频型电感器分规范

Inspection requirements and tests from which a selection is made when preparing a detail specification for variable r.f. type inductors to be released under the terms of BS 9720 capability approval. Shows required format and lists appropriate ratings and characteristics.

Sectional specification for variable r.f. type inductors of assessed quality for use in electronic equipment for capability approval

BS 9741:1986 电子设备性能鉴定用的经质量评定的电感器分规范

Inspection requirements and tests from which a selection is made when preparing a detail specification for inductors to be released under the terms of BS 9720 capability approval. Shows required format and lists appropriate ratings and characteristics. Does not embody an assessment level which is now set by the customer.

Sectional specification for inductors of assessed quality for use in electronic equipment for capability approval

SJ 2697-1986 雷达用高压充电电感通用技条件

本标准适用于雷达发射机和其它类似设备中带有铁芯的充电电感(CHARGINGINDUCTOR)简称CI。其充电电压为1kV至50kV，重量在数公斤至数百公斤之间。

General specification for high voltage charging inductor for radar (Applicable for certification)

IEC 60852-1:1986 通信和电子设备用变压器和电感器的外形尺寸 第1部分:使用YEI-1型铁芯片的变压器和电感器

Specifies the outline dimensions of transformers and inductors, using E and I laminations, built for the three most commonly used forms of mounting style, namely bracket mounting, U-clamp mounting and printed wiring board mounting.

Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment. Part 1 : Transformers and inductors using YEI-1 laminations

BS 9727:1985 电子设备性能鉴定用的经质量评定的电源变压器分规范

Shows required format and lists appropriate tests, ratings and characteristics.

Sectional specification for power transformers of assessed quality for use in electronic equipment for capability approval