L19 磁性元器件 标准查询与下载

BS EN 60556:2006 用于微波频率的旋磁材料.性能的测量方法

This International Standard describes methods of measuring the properties used to specify polycrystalline microwave ferrites in accordance with IEC 60392 and for general use in ferrite technology. These measuring methods are intended for the investigation of materials, generally referred to as ferrites, for application at microwave frequencies. Single crystals and thin films generally fall outside the scope of this standard.

Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties

DIN EN 62317-4:2006 铁氧体磁心.尺寸.第4部分:RM磁心及其相关部分(IEC 62317-4:2005)

This standard specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of RM cores and low profile RM cores made of magnetic oxides, and the locations of their terminal pins on a 2,54 mm printed wiring grid in relation to the base outlines of the cores. It also specifies the test conditions and clamping forces to be used for inductance measurement.

Ferrite cores - Dimensions - Part 4: RM-cores and associated parts (IEC 62317-4:2005); German version EN 62317-4:2005

DIN EN 62317-7:2006 铁氧体磁心.尺寸.第7部分:EER磁心(IEC 62317-7:2005)

Ferrite cores - Dimensions - Part 7: EER-cores (IEC 62317-7:2005); German version EN 62317-7:2005

IEC 62317-9:2006 铁氧体磁心.尺寸.第9部分:平面磁心

This International Standard specifies the shapes and dimensions of ferrite cores for inductive components (transformers and chokes) of which the coil is typically constructed by multi-layer board or the coil is part of the motherboard. The general consideration upon which the design of^his range of cores is based is given in Annex A.

Ferrite cores - Dimensions - Part 9: Planar cores

IEC 60205:2006 磁性零件有效参数的计算

This International Standard lays down uniform rules for the calculation of the effective parameters of closed circuits of ferromagnetic material.

Calculation of the effective parameters of magnetic piece parts

IEC 60556:2006 用于微波频率的旋磁材料.性能的测量方法

This International Standard describes methods of measuring the properties used to specify polycrystalline microwave ferrites in accordance with IEC 60392 and for general use in ferrite technology. These measuring methods are intended for the investigation of materials, generally referred to as ferrites, for application at microwave frequencies. Single crystals and thin films generally fall outside the scope of this standard. NOTE 1 For the purposes of this standard, the words “ferrite” and “microwave” are used in a broad sense: – by “ferrites” is meant not only magneto-dielectric chemical components having a spinel crystal structure, but also materials with garnet and hexagonal structures; – the “microwave” region is taken to include wavelengths approximately between 1 m and 1 mm, the main interest being concentrated on the region 0,3 m to 10 mm. NOTE 2 Examples of components employing microwave ferrites are non-reciprocal devices such as circulators, isolators and non-reciprocal phase-shifters. These constitute the major field of application, but the materials may be used in reciprocal devices as well, for example, modulators and (reciprocal) phase-shifters. Other applications include gyromagnetic filters, limiters and more sophisticated devices, such as parametric amplifiers.

Gyromagnetic materials intended for application at microwave frequencies - Measuring methods for properties

KS C IEC 60205:2006 磁性零件有效参数的计算

이 규격은 강자성체의 폐자기 회로에서 유효 변수를 계산하기 위한 통일된 규칙에 적용 한다.

Calculation of the effective parameters of magnetic piece parts

KS C IEC 60133:2006 磁性氧化物制罐形磁芯及相关件的尺寸

이 규격은 산화물 자성체로 만든 포트(pot) 코어에서 기계적인 호환성이 중요한 치수와 그

Dimensions of pot-cores made of magnetic oxides and associated parts

NF C93-345:2006 软磁铁氧体材料分类

Soft ferrite material classification.

NF C93-357-7:2006 铁氧体磁心.尺寸.第7部分:EER磁心

Ferrite cores - Dimensions - Part 7 : EER-cores.

BS EN 62317-7:2005 铁氧体磁心.尺寸.EER型磁芯

This part of IEC 62317 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EER-cores made of ferrite, the essential dimensions of coil formers to be used with them, and the effective parameter values to be used in calculations involving them.

Ferrite cores - Dimensions - Part 7: EER-cores

DIN EN 62323:2006 电感近接开关用铁氧体半壶形磁芯的尺寸

This International Standard lays down the important dimensions for the mechanical interchangeability of a preferred half pot-core series of ferrite, intended to be used in inductive proximity switches.#,,#

Dimensions of half pot-cores made of ferrite for inductive proximity switches (IEC 62323:2005); German version EN 62323:2005

DIN EN 62044-2:2006 软磁材料磁芯.测量方法.第2部分:低冲击水平下的磁化特性

This standard applies to magnetic cores, mainly made of magnetic oxides or metallic powders, used at low excitation level in inductors and transformers for telecommunication equipment and electronic devices employing similar techniques.

Cores made of soft magnetic materials - Measuring methods - Part 2: Magnetic properties at low excitation level (IEC 62044-2:2005); German version EN 62044-2:2005

BS EN 62323:2005 电感接近开关用铁氧体半壶形磁芯的尺寸

This International Standard lays down the important dimensions for the mechanical interchangeability of a preferred half pot-core series of ferrite, intended to be used in inductive proximity switches.

Dimensions of half pot-cores made of ferrite for inductive proximity switches

BS EN 61185:2005 电源用铁氧体磁芯(ETD磁芯).尺寸

This International Standard specifies the dimensions that are of importance for mechanical interchangeability for ETD-cores made of ferrite, the essential dimensions of coil formers to be used with them, and the effective parameter values to be used in calculations involving them. NOTE 1 Whilst this standard mainly applies to ferrite, its validity for iron powder cores should not be overlooked. NOTE 2 The cores covered by this standard are designed for use in power transformers and chokes operating at high flux density and generally at frequencies higher than those feasible with EC-cores of the same material, due to a core proportioning more suitable for high-frequency applications. They are generally used in pairs. The use of “derived” standards which give more detailed specifications of component parts whilst still permitting compliance with this standard is discussed in Annex A, which also contains an example of a derived standard for coil formers.

Ferrite cores (ETD-cores) intended for use in power supply applications - Dimensions

NF C93-339:2005 电源用铁氧体芯(ETD芯).尺寸

Ferrite cores (ETD-cores) intended for use in power supply applications - Dimensions.

IEC 61332:2005 软磁铁氧体材料分类

This International Standard specifies classification rules for soft ferrite materials used in inductive components (inductors and transformers) fulfilling the requirements of the electronic industries. This standard addresses the following purposes for ferrite suppliers and users: - cross-reference between materials from multiple suppliers; - assistance to customers in understanding the published technical data in catalogues when comparing multiple suppliers; - guidance to customers in selecting the most applicable material for each application; - setting of nomenclature for IEC standards relating to ferrite; - establishing uniform benchmarks for suppliers for performance in new development of materials. The numerical values given in this standard are typical values of parameters (properties) of the related materials. Direct translation from the material specification into the core specification is not always easy or possible. Every detailed material and core specification should be agreed upon between the user and the manufacturer.

Soft ferrite material classification

IEC 62317-7:2005 铁氧体磁心.尺寸.第7部分:EER磁心

This part of IEC 62317 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of EER-cores made of ferrite, the essential dimensions of coil formers to be used with them, and the effective parameter values to be used in calculations involving them.

Ferrite cores - Dimensions - Part 7: EER-cores

IEC 62317-4:2005 铁氧体磁心.尺寸.第4部分:铁氧体RM磁心及相关部件

This part of IEC 62317 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of RM-cores and low-profile RM-cores made of ferrite, and the locations of their terminal pins on a 2,54 mm printed wiring grid in relation to the base outlines of the cores. It also specifies the test conditions and clamping forces to be used for inductance measurement. The general considerations that the design of this range of cores is based upon are given in Annex A.

Ferrite cores - Dimensions - Part 4: RM-cores made of ferrite and associated parts

BS EN 62044-2:2005 软磁材料制芯.测量方法.在低激发能级下的电磁特性

This part of IEC 62044 applies to magnetic cores, mainly made of magnetic oxides or metallic powders, used at low excitation level in inductors and transformers for telecommunication equipment and electronic devices employing similar techniques. Some of the methods described in this part of IEC 62044 may also be suitable for magnetic cores used in other components. This part of IEC 62044 gives guidance for the drafting of those parts of specifications for magnetic cores that are concerned with measuring methods for magnetic and electric core properties. This part of IEC 62044 is limited to the general principles to be followed for various possible test methods and sets out the factors to be taken into account when deciding on the description of the test method to be included in the specification. NOTE All the formulae in this part of IEC 62044 use basic SI units. When multiples or submultiples are used, the appropriate power of 10 should be introduced. The conversion factor for inductances and inductance factors is as follows: 1 H = 10 nH.

Cores made of soft magnetic materials - Measuring methods - Magnetic properties at low excitation level