L24 安装、接线连接件 标准查询与下载

NF C93-462/A2:1981 NF C 93-462-1981的补充件2

Supplement 2 to NF C 93-462-1981

NF C93-462/A1:1981 NF C 93-462-1981的补充件1

Supplement 1 to NF C 93-462-1981

NF C93-462:1981 电子设备元件.终端连接系统.可移动压接型模件.触点.一般要求

Components for electronic equipment. Terminal junction system. Modules with removable crimp-type. Contacts. General requirements.

DIN 46295-3:1981 带有６个开口螺栓的矩形端子板.电缆端头

Terminal board, square shaped with six slit-bolts; cable socketsFür den Anwendungsbereich dieser Norm bestehen keine entsprechenden regionalen oder internationalen Normen.

Terminal board, square shaped with six slit-bolts; cable sockets

DIN 46295-2:1981 带６个开口螺栓的矩形接线板.附件

Terminal board, square shaped with six slit-bolts; accessoriesFür den Geltungsbereich dieser Norm bestehen keine entsprechenden regionalen oder internationalen Normen.

Terminal board, square shaped with six slit-bolts; accessories

DIN 42801:1980 电位均衡导线用接线装置

Connection device for potential equalization conductorsFür den Geltungsbereich dieser Norm bestehen keine entsprechenden regionalen oder internationalen Normen.

Connection device for potential equalization conductors

ANSI/ASTM B615:1979 滑动电触点电接触噪音测量惯例

This practice describes the practices and factors considered to be most important in the measurement of electrical contact noise of sliding contacts. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Practice for Measuring Trical Contact Noise in Sliding Electrical Contacts

ITU-R F.454-1-1978 高频单边带和独立单边带降低载波系统的导频载波标准.第3Aa－技术特性

SIGNAL-TO-NOISE RATIOS IN SIDEBAND AND CARRIER CHANNELS

Pilot Carrier Level for HF Single-Sideband and Independent-Sideband Reduced-Carrier Systems - Section 3Aa - Technical Characteristics

DIN 46216:1976 带槽的冲压焊片

Stamped solder lugs; with slot

Stamped solder lugs, with slot

DIN 46215:1976 带孔压制焊片

Stamped solder lugs; with hole

Stamped solder lugs, with hole

IEC 60149-2K:1976 第11次补充

Sockets and accessories for electronic plug-in devices. Part 2 : Specification sheets for sockets and dimensions of wiring jigs and pin straighteners.

IEC 60149-3A:1976 第1次补充

Sockets and accessories for electronic plug-in devices. Part 3 : Sockets for crystal holders.

ANSI/ASTM B613:1976 滑动电触点复合材料微型电刷制备规范指南

This guide defines the criteria for composition, properties, and other requirements for brushes containing a matrix of one or more conducting metallic elements or alloys and one or more lubricating lamellar solids. The resulting specification is intended for use where the size (for example, 5 by 3 by 2 mm), shape, or other factors preclude the determination of properties on specimens of the bulk material from which individual brushes are made. The requirements recommended herein have been found to be desirable for most brush material composites. Care must be taken in preparing a specification for a pre-existing material that imposition of one or more provisions herein does not alter the material or its performance. The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Guide for Preparing Specifications for Miniature Brushes of Composite Materials for Sliding Electric Contacts

IEC 60149-2L:1976 第12次补充

Sockets and accessories for electronic plug-in devices. Part 2 : Specification sheets for sockets and dimensions of wiring jigs and pin straighteners.

JIS C 6575:1975 电子设备用筒形熔断器

Cartridge fuses for electronic equipment

DIN 46288:1974 导线连接垫圈

Connecting washers for conductorsAnschlu?scheiben nach dieser Norm sind vorzugsweise für die Verwendung bei raumsparenden Konstruktionen vor-gesehen und für den Anschlu? von 1 oder 2 Leitern mit gleichen oder verschiedenen Querschnitten geeignet. Sie hab

Connecting Washers for Conductors

DIN 46285:1972 交流380V直流440V.2.5MM2平方以下导线的一极至三极插座式端子板（灯具端子）

One to three-pole socket terminal strips (lighting fixture terminals) 380 V A. C. and 440 V D. C. for conductors up to 2,5 mmEs wird auf die entsprechenden Bestimmungen, z. B. VDE 0606, VDE 0609, hingewiesen. Die Kriech- und Luftstrecken entsprechen

One to three-pole socket terminal strips (lighting fixture terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm<(hoch)2>

DIN 46284:1972 交流380V直流440V.2.5mm2平方以下导线的二极和三极插座式端子板(仪器端子)

Two- and three-pole socket terminal strips (appliance terminals) 380 V A. C. and 440 V D. C. for conductors up to 2,5 mmEs wird auf die entsprechenden Bestimmungen, z. B. VDE 0606, VDE 0609, hingewiesen. Die Kriech- und Luftstrecken entsprechen VDE

Two- and three-pole socket terminal strips (appliance terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm<(hoch)2>

DIN 41226:1972 电讯工程.钎焊分电器.要求和试验条件

Electrical communication engineering; soldering distributor; requirements and test conditions

Electrical communication engineering; soldering distributors, requirements and test conditions

DIN 41225:1972 钎焊片端子板

Soldering-tag terminal strip

Soldering-tag terminal strip