共找到 433 条与 继电器、斩波器 相关的标准,共 29 页
This specification covers the general requirements for highimpact (HI) shockproof relays for electric equipment for Naval shipboard installation.
RELAYS-POWER, ELECTRICAL SPECIALTY, INDUCTION TYPE, NAVAL SHIPBOARD USE
この規格は。周波数50Hz若しくは60Hzの交流250V以下又は直流250V以下の電路に使う定格通電電流5A以下の工業用制御回路及び電子機器の主として信号伝達回路に使用するリードリレーについて規定する。備考ここでいうリードリレーとは,ガラス管封入形で水銀の入らないリードコンタクトを使用したリードリレーをいう。
Control reed relays
Electrical relays. Single input energizing quantity measuring relays with dependent specified time.
Supplement 1 to NF C 45-211-1977
Marking of part numbers of relays for use in electronic equipment
This amendment forms apart of Mllitary Specification MIL-R-83516A(USAF), dated 3 March 1983, and Is approved for use by the Department of the Air Force and is available for use by all Departments and Agencies of the Deparment of Defense.
RELAYS, REED, DRY, GENERAL SPECIFICATION FOR
本标准规定的负载电流最大达10A,切换功率在直流300W或交流1200VA以下的混合式和固体时间继电器通用技术要求。这些继电器供电子、通信设备及自动、运动装置等延时转换电路用。 本标准是电子时间继间器设计、生产和使用的依据,也是制订产品标准的依据。
Generic specification for electronic time relays
1.1 本标准是电于没备用于簧继电器设计、生产和使用的依据,也是制定产品标准的依据。 1.2 本标准中继电器的分类及型号命名标志方法按部标准SJ 151-80《电子设备用继电器型号命名标志方法》。 1.3 继电器的线圈额定电压系列为(V): 直流:3;5;6;9;12;15;24;48; (9;15为非优先值)。 1.4 继电器触点的额定值仅给出一种直流阻性负载数值。 1.5 本标准中标注的所有尺寸均以毫米(mm)为单位。
Preferred series of dry reed relays
1.1 本标准适用于电子、通讯设备和自动、信号装置用于簧继电器。继电器的触点负载电流可达2 A,触点切换功率可达200W。 本标准是干簧继电器设计、生产和使用的依据,也是制订产品标准的依据。 1.2 使用环境条件 各型干簧继电器的使用环境条件等级须符合下列1.2.1款至1.2.7款规定。
Generic specification for dry reed relays
Electrical relays. Terminal marking.
Electrical relays. General purpose relays. Part 1 : all-or-noting relays with non-specified time. Qualification standard.
Relays of assessed quality with control failure rate for severe environmental conditions.
This s p e c i f l c a t i o n e s t a b l l s h e s t h e general r e q u i r e m e n t s f o r dry reedrelays.*e
RELAYS, REED, DRY, GENERAL SPECIFICATION FOR
Electrical relays. Part 19 : Sectional specification: Electromechanical all-or-nothing relays of assessed quality
Electrical relays. Part 19 : Sectional specification: Electromechanical all-or-nothing relays of assessed quality. Test schedules 1, 2 and 3
Harmonized system of quality assessment for electronic component.S blank detail specification. Electromechanical all-or-no thing relays.
Harmonized system of quality assessment for electronic components. Sectional specification. Electromechanical all-or-nothing relays.
ELECTRICAL RELAYS. ALL OR NOTHING CONTACT RELAYS OF ASSESSED QUALITY. GENERAL REQUIREMENTS.
Specifies the external dimensions for general purpose all-or-nothing electrical relays within the scope of IEC, and the location of their terminals and fixings in terms of preferred multiples of specified modules. Applies equally to all such relays regardless of their type of construction (e.g. electromechanical, electronic, reed, etc.) and includes the height of the socket when the relay is socket-mounted.
Electrical relays. Part 18 : Dimensions for general purpose all-or-nothing relays
Specifies the general requirements for impedance measuring relays as well as test methods and methods of presenting relay characteristics and performance. Covers multi-input energizing quantity measuring relays in which impedance is a characteristic quan
Electrical relays. Part 16 : Impedance measuring relays
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号