L51 激光器件 标准查询与下载

KS C IEC 60825-2:2003 激光产品的安全.第2部分:光纤通信系统的安全性

이 규격은 광원으로부터 먼 거리의 광 전송을 이용하는 광섬유 및 제어 통신 시스템을 안전하

Safety of laser products-Part 2:Safety of optical fiber communication systems

KS B ISO 11254-1:2003 激光和激光相关设备.光表面激光损伤阈值的测定.1对1试验

이 규격은 단일 숏 레이저 방사 유도에 대한 광소자 표면의 손상 문턱값(LIDT)을 결

Laser and laser-related equipment-Determination of laser-induced damage threshold of optical surfaces-Part 1:1-on-1 test

KS B ISO 11151-1:2003 激光和激光设备.标准光学元件.第1部分:紫外线、可见和近红外光谱范围用元件

이 규격은 파장 190~2100 nm의 자외선, 가시광 및 근적외선 스펙트럼 대역에서

Lasers and laser-related equipment-Standard optical components-Part 1:Components for the UV, visible and near-infrared spectral ranges

KS B ISO 11253:2003 激光和激光设备.激光装置.机械接口

이 규격은 레이저의 빔을 중심으로 레이저 소자에 외부 소자들을 부착할 때 필요한 설치

Lasers and laser-related equipment-Laser device-Mechanical interfaces

KS B ISO 11146:2003 激光和激光相关设备.激光束参数试验方法.宽度、发散角与光束传输因子

이 규격은 레이저빔의 빔 폭(지름), 빔 발산각 및 빔 전파 계수를 측정하는 방법에 대

Lasers and laser-related equipment-Test methods for laser beam prarameters-Beam widths, divergence angle and beam propagation factor

KS B ISO 11151-2:2003 激光和激光设备.标准光学元件.第2部分:红外光谱范围用元件

이 규격은 파장 2.10~15.0 mm의 스펙트럼 대역에서 사용되는 레이저 부품에 대한

Lasers and laser-related equipment-Standard optical components-Part 2:Components for the infrared spectral range

BS EN ISO 15367-1:2003 激光和激光相关设备.测定激光束波阵面形状的试验方法.术语及基础领域

ISO 15367-1:2003 specifies methods for the measurement of the topography of the wavefront of a laser beam by measurement and interpretation of the spatial distribution of the phase of that wavefront across a plane approximately perpendicular to its direction of propagation. Requirements are given for the measurement and analysis of phase distribution data to provide quantitative wavefront parameters and their uncertainty in a test report. The methods described in ISO 15367-1:2003 are applicable to the testing and characterization of a wide range of beam types from both continuous wave and pulsed lasers. Definitions of parameters describing wavefront deformations are given together with methods for the determination of those parameters from phase distribution measurements.

Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront - Terminology and fundamental aspects

DIN EN ISO 12005:2003 激光和激光相关设备.激光束参数的试验方法.偏振

This Standard defines a method for determining the polarization status and, whenever possible, the degree of polarization of laser beams.

Lasers and laser-related equipment - Test methods for laser beam parameters - Polarization (ISO 12005:2003); German version EN ISO 12005:2003

DIN EN ISO 11670:2003 激光和激光相关设备.激光束参数的试验方法.束定位稳定性

This standard defines methods for determining laser beam positional as well as angular stability. The test methods given in this standard are intended to be used for testing and characterization of lasers.

Lasers and laser-related equipment - Test methods for laser beam parameters - Beam positional stability (ISO 11670:2003); German version EN ISO 11670:2003

DIN EN ISO 17526:2003 光学和光学仪器.激光器和激光相关设备.激光器的使用寿命

Optic and optical instruments - Lasers and laser-related equipment - Lifetime of lasers (ISO 17526:2003); German version EN ISO 17526:2003

ISO 15367-1:2003 激光及激光相关设备.激光束波前形状测定用试验方法.第1部分:术语和基础领域

This part of ISO 15367 specifies methods for the measurement of the topography of the wavefront of a laser beam by measurement and interpretation of the spatial distribution of the phase of that wavefront across a plane approximately perpendicular to its direction of propagation. Requirements are given for the measurement and analysis of phase distribution data to provide quantitative wavefront parameters and their uncertainty in a test report. The methods described in this part of ISO 15367 are applicable to the testing and characterization of a wide range of beam types from both continuous wave and pulsed lasers. Definitions of parameters describing wavefront deformations are given together with methods for the determination of those parameters from phase distribution measurements.

Lasers and laser-related equipment - Test methods for determination of the shape of a laser beam wavefront - Part 1: Terminology and fundamental aspects

IEC TR 60825-5:2003 激光产品的安全.第5部分:制造商关于IEC 60825-1的检查清单

Safety of Laser Products - Part 5: Manufacturer?s Checklist for IEC 60825-1 (Edition 2.0)

ISO 17526:2003 光学和光学仪器.激光器和激光相关设备.激光器的使用寿命

This International Standard covers terms and definitions as well as test methods and evaluation procedures to characterize, estimate and predict the longterm behaviour of various types of lasers. This International Standard defines terms for the lifetime of lasers and specifies test procedures and fundamental aspects for the determination of lifetime. It applies for all types of lasers for which lifetime is a critical issue, including diode lasers except those used in telecommunications.

Optics and optical instruments - Lasers and laser-related equipment - Lifetime of lasers

BS EN ISO 12005:2003 激光器和激光相关设备.激光束参数的试验方法.偏振

The purpose of this International Standard is to assist technical standardization committees responsible for specific families of machinery or equipment in pre-paring noise test codes to ensure that such noise test codes

Lasers and laser-related equipment. Test methods for laser beam parameters. Polarization

BS EN ISO 11670:2003 激光器和激光相关设备.激光束参数的试验方法.束定位稳定性

This International Standard is not applicable unless the applications cover the whole frequency range of the reference curve. If only a part of this range is of interest, it may be more appropriate to look for products with a good sound absorption within this range only. The shape indicators described in this International Standard give some guidance in identifying such products which may have a relatively low single number but a much higher potential if a more restricted frequency range is considered. Such products should be judged from the complete sound absorption curve.

Lasers and laser-related equipment - Test methods for laser beam parameters - Beam positional stability

EN ISO 11670:2003 激光和激光相关设备.激光束参数的试验方法.激光束位置稳定性

This International Standard specifies methods for determining laser beam positional as well as angular stability. The test methods given in this International Standard are intended to be used for the testing and characterization of lasers.

Lasers and laser-related equipment - Test methods for laser beam parameters - Beam positional stability ISO 11670: 2003

ISO 11554:2003 光学和光学仪器.激光和相关激光设备.激光束功率、能量和时间特征的试验方法

This International Standard specifies test methods for determining the power and energy of continuous-wave and pulsed laser beams, as well as their temporal characteristics of pulse shape, pulse duration and pulse repetition rate. Test and evaluation methods are also given for the power stability of cw-lasers, energy stability of pulsed lasers and pulse duration stability. The test methods given in this International Standard are to be used for the testing and characterization of lasers.

Optics and optical instruments - Lasers and laser-related equipment - Test methods for laser beam power, energy and temporal characteristics

ISO 12005:2003 激光和激光设备.激光束参数的试验方法.偏振

This International Standard specifies a method for determining the polarization status and, whenever possible, the degree of polarization of the beam from a continuous wave (cw) laser. It can also be applied to repetitively pulsed lasers, if their electric field vector orientation does not change from pulse to pulse. This International Standard also specifies the method for determining the direction of the plane of oscillation in the case of linearly polarized (totally or partially) laser beams. It is assumed that the laser radiation is quasi-monochromatic and sufficiently stable for the purpose of the measurement. The knowledge of the polarization status can be very important for some applications of lasers with a high divergence angle, for instance when the beam of such a laser shall be coupled with polarization dependent devices (e.g. polarization maintaining fibres). This International Standard also specifies a method for the determination of the state of polarization of highly divergent laser beams, as well as for the measurement of beams with large apertures.

Lasers and laser-related equipment - Test methods for laser beam parameters - Polarization

ISO 11990:2003 光学和光学仪器.激光和激光设备.气管柄激光抗性的测定

This International Standard specifies a method of testing the continuous wave (cw) laser resistance of the shaft of a tracheal tube. Other components of the system, such as the inflation system and cuff, are outside the scope of this International Standard. The specified test method shall be used to measure and describe the properties of materials, products or assemblies in response to heat and flame under controlled laboratory conditions and shall not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all the factors which are pertinent to an assessment of the hazard of a particular end use. Caution should be observed in interpreting these results, since the direct applicability of the result of this test method to the clinical situation has not been fully established. NOTE This test method may involve hazardous materials, operations, and equipment. This International Standard does not purport to address all the safety problems associated with its use. It is the responsibility of the user of this test method to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Optics and optical instruments - Lasers and laser-related equipment - Determination of laser resistance of tracheal tube shafts

ISO 11670:2003 激光和激光设备.激光束参数的试验方法.束定位稳定性

This International Standard specifies methods for determining laser beam positional as well as angular stability. The test methods given in this International Standard are intended to be used for the testing and characterization of lasers.

Lasers and laser-related equipment - Test methods for laser beam parameters - Beam positional stability