L65 系统设备接口 标准查询与下载

ECA SP 4971-2001 1.27mm间距、68环形存储卡互连系统的详细规范发表为ANSI/EIA-700AOAB

Standards Proposal No. 497 1 , Proposed Reaffirmation of ANSIEIA-700AOAB “Detail

Detail Specification for 1.27 mm Pitch, 68 Circuit Memory Card Interconnect System To be published as ANSI/EIA-700AOAB

SJ/T 11229-2001 手持式个人信息处理设备中文应用程序接口规范

本规范规定了手持式个人信息处理设备的中文应用程序接口，包括所采用字符集、字库文件结构、输入法接口、文本接口。本规范适用于手持式个人信息处理设备的研制和生产。

Chinese API specification for hand-hold personal information processing devices

ISO/IEC 11518-10:2001 信息技术 高性能平行接口 第10部分：6400Mbit/s物理层（HIPPI-6400-PH）

This part of ISO/IEC 11518 specifies a physical-level, point-to-point, full-duplex, link interface for reliable, flow-controlled transmission of user data at 6 400 Mbrt/s per direction, across distances of up to 1 km. A parallel copper cable interface for distances of up to 40 m is specified. Connections to a separate longer-distance optical interface are provided. Small fixed-size micropackets provide an efficient, low-latency structure for small transfers, and a component for large transfers. Specifications are included for: - automatic retransmission to correct flawed data; - the format of a small data transfer unit called a micropacket; - a message structure that includes routing information for network applications; - end-to-end, as well as link-to-link, checksums; - the timing requirements of the parallel signals; - a parallel interface using copper coaxial cable; - connections to a separate local optical interface; - a link-level protocol tuned for a maximum distance of 1 km.

Information technology - High-performance parallel interface - Part 10: 6400 Mbit/s Physical Layer (HIPPI-6400-PH)

IEEE 1386 and IEEE 1386.1-2001 PCI中间卡(PMC)的通用中间卡(CMC)物理层和环境层

Common mezzanine card (CMC) family and physical and environmental layers for PCI mezzanine cards (PMC)

ANSI/INCITS 323 AMD 1-2001 信息技术.高性能并行接口.6400Mbit/s物理层.修改件1

Reaffirmation of Ammendment 1 which consists of corrections to NCITS 323:1998.

Information Technology - High-Performance Parallel Interface - 6400 Mbit/s Physical Layer Amendment 1

ISO/IEC 13961:2000 信息技术 可伸缩相干接口(SCI)

This standard will encompass two levels of interface, defining operation over distances less than 10 m. The physical layer will specify electrical, mechanical, and thermal characteristics of connectors and cards. The logical level will describe the address space, data transfer protocols, cache coherence mechanisms, synchronization primitives, control and status registers, and initialization and error recovery facilities.

Information technology - Scalable Coherent Interface (SCI)

CEA-844-2000 通用共同的应用程序语言(通用华航)的XML编码

This report is based on the following technical specifications:ANSI/EIA-721 Generic Common Application Language (Generic CAL)

XML Encoding of Generic Common Application Language (Generic CAL)

CEA-709.2-A-2000 控制网络电力线(PL)通道规格

This document specifies the EIA-709 Control Network Power Line (PL) Channel and serves as a companion document to EIA-709.1-A [1]. Its purpose is to present the information necessary for the development of a PL physical network and nodes to communicate and share information over that network.

Control Network Power Line (PL) Channel Specification

ISO/IEC 9316-2:2000 信息技术.小型计算机系统接口2(SCSI-2).第2部分:公共访问方法(CAM).运输和SCSI接口模块

This International Standard defines the Common Access Method (CAM) for the Small Computer Systems Interface (SCSI). The purpose of this International Standard is to define a method whereby multiple environments may adopt a common procedure for the support of SCSI devices. The CAM provides a structured method for supporting peripherals with the software (e.g. device driver) and hardware (e.g., host bus adapter) associated with any computer.

Information technology - Small computer system interface-2 (SCSI-2) - Part 2: Common Access Method (CAM); Transport and SCSI interface module

ISO/IEC 14776-381:2000 信息技术 小型计算机系统接口(SCSI) 第381部分:光存储卡设备命令(OMC)

This standard defines the command set extensions to facilitate operation of optical memory card devices. The clause(s) of this standard pertaining to optical memory card device class, implemented in conjunction with the applicable clauses of the ISO/IEC 14776-311 SCSI-3 Primary Commands (SPC) and the ISO/IEC 14776-321 SCSI-3 Block Commands (SBC), fully specify the standard command set for optical memory card devices.

Information technology - Small computer system interface (SCSI) - Part 381: Optical Memory Card Device Commands (OMC)

ISO/IEC 14776-341:2000 信息技术.小型计算机系统接口-3(SCSI-3).第341部分:控制器命令(SCC)

This International Standard defines the command set extensions for SCSI-3 storage array devices; commonly known as RAID devices. This standard is principally intended to be used in conjunction with, not as an alternate to, any of the SCSI-3 command standards and the SCSI-3 Architecture Model Standard (ISO/IEC IS 14776-411). The resulting commands facilitate the control and configuration of SCSI-3 storage arrays and thus provide a common command specification for both system integrators and suppliers of SCSI-3 storage array devices. The clause(s) of this standard pertaining to the SCSI-3 storage array device class, implemented in conjunction with the applicable clauses within any of the SCSI-3 command standards, shall specify the standard command set available for SCSI-3 storage arrays. The objectives of the SCSI-3 Controller Commands is to provide the following: a) Transfer commands unique to SCSI-3 Controller Command devices; b) Control commands to manage the operation of an SCSI-3 Controller Command device; c) Optional device mapping and pass-through support.

Information technology - Small Computer System Interface-3 (SCSI-3) - Part 341: Controller Commands (SCC)

ISO/IEC 14776-342:2000 信息技术 小型计算机系统接口 第342部分:控制器命令2(SCC-2)

This International Standard defines the command set extensions for SCSI storage array devices; commonly known as RAID devices. This standard is principally intended to be used in conjunction with, not as an alternate to, any of the SCSI command standards nor to the SCSI-3 Architecture Model (ISO/IEC 14776-411) standard. This international standard is intended as an alternate to the SCSI-3 Controller Command (ISO/IEC 14776-341) standard. The resulting commands facilitate the control and configuration of SCSI storage arrays and thus provide a common command specification for both system integrators and suppliers of SCSI storage array devices. This international standard contains all the information defined in SCSI-3 Controller Command (ISO/IEC 14776-341) standard. In addition this international standard specifies new commands and an expanded model clause. The clause(s) of this standard pertaining to the SCSI storage array device class, implemented in conjunction with the applicable clauses within any of the SCSI command standards, shall specify the standard command set available for SCSI storage arrays. The objective of the SCSI Controller Commands is to provide the following: a) Transfer commands unique to SCSI Controller Command devices; b) Control commands to manage the operation of an SCSI Controller Command device; c) Optional device mapping and pass-through support.

Information technology - Small Computer System Interface - Part 342: Controller Commands-2 (SCC-2)

CEA-827-2000 声音水平测量－车辆安全系统音响器件

This standard defines the method for measuring the noise level of a vehicle security-sounding device. This standard does not define or limit device under test (DUT) frequencies, sounds or tones. However, this standard limits the frequencies that the noise level measurements may measure. Only frequencies between 500 Hz and 3,500 Hz shall be accepted for measurement purposes. If the DUT has multiple frequencies, only those that are within these limits shall be acceptable for measurement. Suitable spectral analysis equipment shall be used for the analysis of the frequencies emitted by the DUT. This need not be done at the time of testing.

Sound Level Measurement- Vehicle Security System Sounding Devices

CEA-775.1-2000 加强网络数字电视1394介面规格

This EIA-775.1 standard includes mechanisms to allow a source of MPEG service, such as a cable or terrestrial set-top box, digital VCR, or DTV to utilize the MPEG decoding and display capabilities in a DTV. A control means using web and Internet protocols is the main feature of this standard. It enables user control of remote appliances via another appliance’s (e.g., DTV or PC) web browser graphical user interface (GUI). The controlled service (e.g., MPEG source) passes requested GUI data to the DTV for presentation typically over the decoded video.

Web Enhanced DTV 1394 Interface Specification

CWA 13849-4-2000 ActiveXFS接口规范.ActiveXFS存款处目标接口规范

The XFSDepository Control provides the funtionality required for the operation of an envelope depository. The envelope depository may also have the capability of dispensing envelopes.

ActiveXFS interface specification. ActiveXFS depository object interface specification

CWA 13849-5-2000 ActiveXFS接口规范.ActiveXFS PINPad目标接口规范

The PINPad device provides the mechanism to enable data input within a multi-vendor environment. In addition, along with the security module, costumer PIN's can be encrypted and/or verified. This document specifies the following interfaces: Incoming: IXFSKeyPad, IXFSEncryptor. IXFSPINPadManagement, IXFSPINPad Outgoing: IXFSPINPadEvents.

ActiveXFS interface specification. ActiveXFS PINPad object interface specification

CWA 13849-6-2000 ActiveXFS接口规范.ActiveXFS日志记录打印机目标接口规范

This document specifies the following interfaces: XFSJournalPrinter, XFSJournal, SFSJournalPrinterAction and XFSJournalPrinterCoAction.The Document Printer exposes the functionality of the printer by means of properties, methods and events.

ActiveXFS interface specification. ActiveXFS journal printer object interface specification

CWA 13849-7-2000 ActiveXFS接口规范.ActiveXFS收款打印机目标接口规范

A control and three automation objects are defined for the ReceiptPrinter. The ReceiptPrinter exposes the functionality of the printer by means of properties, methods and events. This document specifies the following interfaces: XFSReceiptPrinter: Incoming: IXFSReceiptPrinter. Outgoing: IXFSReceiptPrinterEvents; XFSReceipt: Incoming: IXFSReceipt; XFSReceiptPrinterAction: Incoming: IXFSReceiptPrinterAction; XFSReceiptPrinterCoAction: Incoming: IXFSReceiptPrinterCoAction.

ActiveXFS interface specification. ActiveXFS receipt printer object interface specification

CWA 13849-8-2000 ActiveXFS接口规范.ActiveXFS文件打印机目标接口规范

This document defines the interfaces supported by the Document Printer Control. The Document Printer exposes the functionality of the printer by means of properties, methods and events. This document specifies the following interfaces: XFSDocumentPrinter: Incoming: IXFSDocumentPrinter. Outgoing: IXFSDocumentPrinterEvents XFSDocument: Incoming: IXFSDocument XFSDocumentPrinterAction: Incoming: IXFSDocumentPrinterAction. XFSDocumentPrinterCoAction: Incoming: IXFSDocumentPrinterCoAction

ActiveXFS interface specification. ActiveXFS document printer object interface specification

CWA 13849-9-2000 ActiveXFS接口规范.ActiveXFS文件打印机目标接口规范

ActiveXFS interface specification. ActiveXFS document printer object interface specification