N22 电能测量和负荷控制系统 标准查询与下载

IEC 61037:1998 电量测量 电费和负荷控制 电子式纹波控制接收机的特殊要求

This International Standard specifies requirements for the type test of indoor electronic ripple control receivers for the reception and interpretation of pulses of a single audio frequency superimposed on the voltage of the electricity distrivution network and for the execution of the corresponding switching operations. In this system the mains frequency is generally used to synchronize the transmitter and receivers. Neither the control frequency,nor the encoding are standardized in this standard. This standard gives no requirements for constructional details internal to the receiver.This standard does not cover the acceptance tests and the conformity tests.(Nevertheless, an example of what could be an acceptance test is given in annex G(informative).) The reliability aspect also is not covered in this standard as there are no short term procedures available which would fit into type test documents to satisfactorily check this requirement.

Electricity metering - Tariff and load control - Particular requirements for electronic ripple control receivers

IEC 61038/AMD2:1998 计费和负载控制用计时开关.第2次修订

Time switches for tariff and load control; Amendment 2

IEC 61037/AMD2:1998 计费和负载控制用电子脉动控制接收装置.第2次修订

Electronic ripple control receivers for tariff and load control; Amendment 2

DIN 43857-5:1998 最大额定电流在60A以下无仪表变压器的模压壳体的电度表.第5部分.端子盖的主要尺寸

The document specifies the principal dimensions for terminal cover for supplementary devices on watthour meters in moulded cases.

Watthour meters in moulded case without instrument transformers up to 60 A rated maximum current - Part 5: Principal dimensions for terminal cover

DL/T 645-1997 多功能电能表通信规约

Multi-function watt-hour meter communication protocol

IEC 62053-61:1998 电量测量设备交流 特殊要求 第61部分:功耗和电压要求

This International Standard applies only to newly manufactured "combined meters", measuring more than one type of electric energy (e.g. active and reactive) and meters integrating additional functions which are not in the scope of the IEC 60687, IEC 61036, IEC 61268 standards and the standard in preparation for static apparent energy meters; these additional functions, all related to electric energy metering are, for instance, maximum demand indicator, time switches, ripple control or radio receivers, etc. When other devices and functions not related to electric energy metering and billing are enclosed in the same meter case (such as power line carrier devices, load curve recording devices, telephone and radio transceiver or network current and voltage measurement and analysis devices, etc.) this standard applies only to the energy metering and processing section. For all the meter characteristics and functions already described in existing standards, these standards will apply for the corresponding characteristics and functions.

Electricity metering equipment (a.c.) - Particular requirements - Part 61: Power consumption and voltage requirements

IEC 62053-31:1998 电量测量设备交流 特殊要求 第31部分:机电和电子仪表的脉冲输出装置(2芯传输)

This part of IEC 62053 is applicable to passive, two-wire, externally powered pulse output devices to be used in electricity meters as defined by the relevant standards of technical committee 13 (see normative references) as well as future standards for static VA-hour meters. Such pulse output devices are used to transmit pulses, representing a finite energy quantity, to a receiver (e.g. a tariff device).

Electricity metering equipment (a.c.) - Particular requirements - Part 31: Pulse output devices for electromechanical and electronic meters (two wires only)

JIS C 1102-3:1997 直接动作指示模拟电气测量仪器及其附件.第3部分:瓦特计和无功功率计的特殊要求

1.1この規格は，アナログ表示の直動式指示電力計及び無効電力計に適用する。備考多機能計器は，JIS C 1102-7による。1.2この規格は，電力計及び無効電力計とともに使用する非互換性附属品(JIS C 1102-1の2.1.15.3に定義する。)にも適用する。1.3-1.8 JIS C 1102-1による。

Direct acting indicating analogue electrical measuring instruments and their accessories Part 3: Special requirements for wattmeters and varmeters

JIS C 1102-5:1997 直接动作指示模拟电气测量仪器及其附件.第5部分:相位表、功率因数表和同步示波器的特殊要求

1.1この規格は，アナログ表示の直動式指示位相計，力率計及び同期検定器に適用する。1.2この規格は，位相計，力率計及び同期検定器とともに使用する非互換性附属品(JIS C 1102-1の2.1.15.3に定義する。)にも適用する。1.3この規格は，目盛か電気的入力量に直接には対応しないが，その間の関係が既知であるような位相計又は力率計にも適用する。1.4-1.8 JIS C 1102-1による。

Direct acting indicating analogue electrical measuring instruments and their accessories Part 5: Special requirements for phase meters, power factor meters and synchroscopes

JB/T 5467-1997 交流有功和无功电度表

AC active and reactive energy meters

JB/T 8610-1997 读表、费率和负荷控制的数据交换 直接本地数据交换

本标准介绍了本地系统的硬件和协议规范,而远地系统的规范列入其他标准中。 本标准论及的是直接本地系统，其中手持单元（HHU）与一台或一组费率装置相连接。通过电气或光耦合的连接可以是永久性的或是可拆离的。协议以开放系统（OSI）间的通讯的基本参考模式为基础。 考虑到目前有些系统已在使用中，所以特别注意到了保证与现有系统和/或系统元件及其有关协议的兼容性。 该协议允许对费率装置进行读取和编程。其设计特别适合于电气测量的环境，尤其是在有电气隔离和软件保护要求的环境。尽管该协议定义明确，但同时它又为用户保留了应用余地。 本标准叙述了允许费率装置与HHU间数据交换的硬件和软件的先决条件。与HHU的连接可以是永久的或可拆离的。可使用电气的和光的耦合器。推荐电气接触作为固定连接。光耦合器应是易拆离的以便通过HHU进行数据采集。本标准包括有ISO 7498的某些部分，并在诸如光学接口、控制波特率变换（切换）的协议以及无接收认可的数据传输方面增添了更多的条件。前期工作以ISO 7498开放系统中的通讯的参考模式作为基础。

Data exchange for meter reading, tariff and load control Direct local data exchange

DL/T 614-1997 多功能电能表

Multifunction watthour meter

DIN 43856-2:1997 电度表.第2部分:符合IEC报告61354:1995的收费装置辅助连接点标注

The document deals with the marking of auxiliary terminals for tariff devices of a.c. electricity meters with induction or static measurement elements.

Electricity meters - Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995

NF C44-104:1997 交流静态瓦时电度表(1级和2级)

Alternating current static watt-hour meters for active energy (classes 1 and 2).

DIN 43862:1996 电度表.带静电测量装置的插入式计数器.主要尺寸

The document deals with the principal dimensions for plug-in-static watthour meters.

Electricity meters - Plug-in static electricity meters - Principal dimensions

BS 7856:1996 交流电设计实用规程,有功功率(1级和2级)瓦时表

Guidance on special UK design practices not covered in BS EN 60521 or BS EN 61036. To be read in conjunction with BS EN 60521:1995, BS EN 61036:1993

Code of practice for design of alternating current, watthour meters for active energy (classes 1 and 2)

IEC 61036:1996 电度计量用交流静态瓦时表(1级和2级)

Alternating current static watt-hour meters for active energy (classes 1 and 2)

NF C44-103:1996 仪表读数的数据交换.费率和负载控制.直接局部数据交换

Data exchange for meter reading, tariff and load control. Direct local data exchange.

NF C44-106/A1:1996 NF EN 61038-1993的修改件1

Amendment 1 to NF EN 61038-1993

NF C44-112:1996 无功交流静态乏时计(2类和3类)

Alternating current static var-hour meters for reactive energy (classes 2 and 3).