P15 工程抗震 标准查询与下载

NF P06-013:1995 建筑的抗地震法规.建筑物适用抗地震法规:PS 92

Earthquake resistant construction rules. Earthquake resistant rules applicable to buildings, called ps 92.

SY 4081-1995 钢制球形储罐抗震鉴定技术标准

本标准适用于抗震设防烈度为6度至9度地区已投入运行的、设置在地表以上、支柱为正切式的球罐下部支承结构(支柱、拉杆、地脚螺栓，基础板等)的抗震鉴定和加固。

Standard for earthquake resistance evaluation of steel spherical tanks

SY 4063-1993 电气设施抗震鉴定技术标准

本技术标准适用于抗震设防烈度为6度至9度地区已投入运行的，电压为6kV至220kV的电气设施的抗震鉴定和加固。

Standard for Earthquake Resistance Evaluation of Electric Facilities

JGJ 68-1990 多孔砖（KP1型）建筑抗震设计与施工规程

Specification for design and construction of earthquake-resistance of porous brick (type KP1) buildings

ISO 3010:1988 建筑设计基础 对建筑物的地震作用

Bases for design of structures; seismic actions on structures

ANSI/ASA S2.32-1982 机械导纳的试验测定方法,第2部分:应用单点平移激发法测量

The scope of this standard includes measurement of mobility, accelerance, or dynamic compliance, either as a driving point measurement, or as a transfer measurement. It also applies to the determination of the arithmetic reciprocals of those ratios as free effective mass. Although excitation is applied at a single point, there is no limit on the number of points at which simultaneous measurements of the motion response may be made. Multiple response measurements are required, for example, for modal analyses.

Methods for the Experimental Determination of Mechanical Mobility, Part 2: Measurements Using Single-Point Translational Excitation

ANSI/ASA S2.31-1979 机械导纳的试验测定方法,第1部分:基本术语和转换器

This document provides basic definitions with comments and identifies the calibration tests, environmental tests, and physical measurements necessary to determine the suitability of impedance heads, force transducers, and accelerometers fo use in measuring mechanical mobility.

Methods for the Experimental Determination of Mechanical Mobility, Part 1: Basic Definitions and Transducers

AS 1170.4:2007(R2018)+A2 结构设计行为.澳大利亚的地震作用

Sets out data and procedures for determining earthquake loads on structures and their components, and also minimum detailing requirements for structures. Domestic structures are covered in an Appendix.

Structural design actions - Earthquake actions in Australia

JBJ 22-1991 隔振设计规范

Specifications for vibration isolation design

JGJ 116-1998（条文说明） 建筑抗震加固技术规程

Technical specification for astigmatic strengthening of buildings

JBJ 12-1997 单层工厂厂房抗震设计规范

Code for design of aseismic single story machine factory building

SY 4063-1993(条文说明) 电气设施抗震鉴定技术标准

Standard for Earthquake Resistance Evaluation of Electric Faciliti(EXPLANATION)

DL 5073-1997 水工建筑物抗震设计规范

Code for seismic design of hydraulic structures

JGJ 101-1996（条文说明） 建筑抗震试验方法规程

Specification for seismic test method of buildings

JGJ/T 97-1995（条文说明） 工程抗震术语标准

Term standard in earthquake engineering(explanation)

JGJ/T 13-1994（条文说明） 设置钢筋混凝土构造柱多层砖房抗震技术规程

Seismic technical specification for multistory masonry buildings with reinforced concrete tie columns

HG/T 20665-1999（条文说明） 化工建、构筑物抗震设防分类标准

Standard for classification of aseismic protection of buildings and structures in chemical industry (explanation)

DL 5073-2000（条文说明） 水工建筑物抗震设计规范

Specifications for seismic design of hydraulic structures(explanation)