P20 工程结构综合 标准查询与下载

JIS A 1515:1998 窗和门组件.风阻力试验

この規格は，JIS A 1513に規定する試験項目のうち，圧力箱方式による建具の耐風圧性試験方法について規定する。

Windows and doorsets -- Wind resistance test

JIS A 1516:1998 窗和门组件.气密性试验

この規格は，JIS A 1513に規定する試験項目のうち，圧力箱方式による建具の気密性試験試験方法について規定する。

Windows and doorsets -- Air permeability test

ISO 2394:1998 结构可靠性的一般原则

This International Standard specifies general principles for the verification of the reliability of structures subjected to known or foreseeable types of action. Reliability is considered in relation to the performance of the structure throughout its design working life. The general principles are applicable to the design of complete structures (buildings, bridges, industrial structures, etc.), the structural elements making up the structure and the foundations. This International Standard is also applicable to the successive stages in construction, namely the fabrication of structural elements, the transport and handling of the structural elements, their erection and all work on site, as well as the use of the structure during its design working life, including maintenance and repair. To allow for the differences in design practice between different countries, the national standards or codes of practice may be simpler or more detailed in comparison with this International Standard. Generally the principles are also applicable to the structural appraisal of existing constructions or assessing changes of use. However in some respects this is associated with special aspects of the basic variables and calculation models. Such aspects are considered in clause 10. NOTE - When this International Standard is applied in a particular country for the development of its standards, it is admissible not to use those clauses which are not in accordance with the regulations of that particular country.

General principles on reliability for structures

DIN 18807-9:1998 建筑物的梯形薄板.第9部分:铝梯形型材及其连接件.使用和构造

This document applies to materials, dimensions, corrosion protection, inspection and marking of aluminium trapezoidal sheeting. The conditions to be complied with during planning and construction have been specified.#,,#

Trapezoidal sheeting in buildings - Part 9: Aluminium trapezoidal sheeting and their connections; application and construction

BS ISO 1803:1997 建筑物结构.公差.尺寸精度表述法.原则和术语

Defines basic principles for expression of dimensional deviation in buildings, including terms and definitions relating to evaluation , specification and verification of accuracy.

Building construction - Tolerances - Expression of dimensional accuracy - Principles and terminology

CJJ 79-1998 联锁型路面砖路面施工及验收规程

Specification for construction and acceptance of interlocking brick pavement

ASTM E72-98 建筑结构用板条的传导强度试验

1.1 These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and roof constructions: Section Test Specimens 3 Loading 4 Deformation Measurements 5 Reports 6 Precision and Accuracy 7 TESTING WALLS Significance and Use 8 Compressive Load 9 Tensile Load 10 Transverse Load-Specimen Horizontal 11 Transverse Load-Specimen Vertical 12 Concentrated Load 13 Impact Load-See Test Methods E 695 and E 661 Racking Load-Evaluation of Sheathing 14 Materials on a Standard Wood Frame Racking Load-Evaluation of Sheathing 15 Materials (Wet) on a Standard Wood Frame TESTING FLOORS Significance and Use 16 Transverse Load 17 Concentrated Load 18 Impact Load-See Test Methods E 695 and E 661 TESTING ROOFS Section Significance and Use 19 Transverse Load 20 Concentrated Load 21 APPENDIX Technical Interpretation XI 1.2 Metric units are to be considered as the primary standard units.

Standard Test Methods of Conducting Strength Tests of Panels for Building Construction

CECS 96-1997 基坑土钉支护技术规程

本规程适用于基坑直立开挖或陡坡开挖时临时性土钉支护的设计与施工，采用以钢筋作为中心钉体的钻孔注浆型土钉，基坑的深度不宜超过18m，使用期限不宜超过18个月。

Specification for soil nailing in foundation excavatons

BS 8000-16:1997 建筑工地操作工艺.建筑物用密封剂的封接件实用规程

Common Arrangement of Work Sections (CAWS) classification P22, Z22.

Workmanship on building sites - Code of practice for sealing joints in buildings using sealants

HB 10139-1997 BS 6399 Pt.2-1997用风荷载计算器

Wind Loading Ready Reckoner for BS 6399:Part 2:1997

BS EN 1618:1997 管内导管除外的其它导管.通用性能的测试法

Specifies test methods for corrosion resistance, tensile properties, leakage of fluids and air, water flow rate and security of connectors.

Catheters other than intravascular catheters - Test methods for common properties

DD ENV 1991-2-4-1997 结构设计和作用力基础知识.对结构的作用力.风的作用力(结合英国国家应用文件一起使用)

Basis of design and actions on structures. Actions on structures. Wind actions (together with United Kingdom National Application Document)

DIN ISO 5261:1997 技术图样.棒材及剖面的简化表示

Technical drawings - Simplified representation of bars and profile sections (ISO 5261:1995)

ASTM E1399-97(2009) 建筑连接系统最小和最大连接宽度的测量和循环运动的标准试验方法

Types of architectural joint systems included in this test method are the following: Metallic systems; Compression seals: With frames, and Without frames, Strip seals; Preformed sealant systems (see Appendix X1): With frames, and Without frames, Preformed foams and sponges: Self-Expanding, and Nonexpanding, Fire barriers: Used as joint systems, and Used as a part of the joint system, and Elastomeric membrane systems: With nosing material(s), and Without nosing material(s). This test method will assist users, producers, building officials, code authorities, and others in verifying some performance characteristics of representative specimens of architectural joint systems under common test conditions. The following performance characteristics are verifiable: The maximum joint width, The minimum joint width, and The movement capability. This test compares similar architectural joint systems by cycling but does not accurately reflect the system''s application. Similar refers to the same type of architectural system within the same subsection under 4.1. This test method does not provide information on: Durability of the architectural joint system under actual service conditions, including the effects of cycled temperature on the joint system, Loading capability of the system and the effects of a load on the functional parameters established by this test method, Rotational, vertical, and horizontal shear capabilities of the specimen, Any other attributes of the specimen, such as fire resistance, wear resistance, chemical resistance, air infiltration, watertightness, and so forth, and Testing or compatibility of substrates. This test method is only to be used as one element in the selection of an architectural joint system for a particular application. It is not intended as an independent pass/fail acceptance procedure. In conjunction with this test method, other test methods are to be used to evaluate the importance of other service conditions such as durability, structural loading, and compatibility. 1.1 This test method covers testing procedures for architectural joint systems. This test method is intended for the following uses for architectural joint systems: 1.1.1 To verify movement capability information supplied to the user by the producer, 1.1.2 To standardize comparison of movement capability by relating it to specified nominal joint widths, 1.1.3 To determine the cyclic movement capability between specified minimum and maximum joint widths without visual deleterious effects, and 1.1.4 To provide the user with graphic information, drawings or pictures in the test report, depicting them at minimum, maximum, and nominal joint widths during cycling. 1.2 This test method is intended to be used only as part of a specification or acceptance criterion due to the limited movements tested. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems

ASTM C1363-97 用隔热箱测定建筑组件的热性能的标准试验方法

1.1 This test method covers the laboratory measurement of heat transfer through a specimen under controlled air temperature, air velocity, and thermal radiation conditions established in a metering chamber on one side and in a climatic chamber on the other side.

Standard Test Method for the Thermal Performance of Building Assemblies by Means of a Hot Box Apparatus

ASTM E1399-97(2005) 建筑连接系统最小和最大连接宽度的测量和循环运动的标准试验方法

1.1 This test method covers testing procedures for architectural joint systems. This test method is intended for the following uses for architectural joint systems:1.1.1 To verify movement capability information supplied to the user by the producer,1.1.2 To standardize comparison of movement capability by relating it to specified nominal joint widths,1.1.3 To determine the cyclic movement capability between specified minimum and maximum joint widths without visual deleterious effects, and1.1.4 To provide the user with graphic information, drawings or pictures in the test report, depicting them at minimum, maximum, and nominal joint widths during cycling.1.2 This test method is intended to be used only as part of a specification or acceptance criterion due to the limited movements tested.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Cyclic Movement and Measuring the Minimum and Maximum Joint Widths of Architectural Joint Systems

DD ENV 1991-2-2-1996 结构设计和作用力基础知识.对暴露于火的结构的作用力(结合英国国家应用文件一起使用)

Basis of design and actions on structures. Actions on structures exposed to fire (together with United Kingdom National Application Document)

DD ENV 1991-1-1996 结构设计和作用力基础知识.设计基础知识(结合与英国国家应用文件一起使用)

Basis of design and actions on structures. Basis of design (together with United Kingdom national application document)

DD ENV 1991-4-1996 结构设计和作用力基础知识.第4部分:竖井和水箱里的作用力

Basis of design and actions on structures. Actions in silos and tanks

CECS 83-1996 管道工程结构常用术语标准

本标准适用于市政和一般工矿企业中管道工程结构，编制标准、规范、手册、教材以及教学和学术交流等有关领域。 本标准规定了术语的涵义及其必要的描述。

TERMS USED IN PIPILINE ENGINEERING STRUCTURES