工程结构综合标准-分析测试百科网

NF P65-202-1:1993 DTU 55-2. 建筑工地.应用石墙包覆法.第1部分:技术规范

DTU 55-2. BUILDING WORKS. APPLIED STONE WALL CLADDING. PART 1 : TECHNICAL SPECIFICATIONS.

ICS: 91.100.15
CCS: P20
发布: 1993-05
实施: 1993-04-05

BOCA CHAPTER 20 NFPC-1993 帐篷和空中支援的结构

The BOCA National Mechanical Code was initially prepared and updated on the premise that adequate code requirements are essential to the safe installation and maintenance of all mechanical equipment and systems in order to protect the public health, sa

Tents and Air-Supported Structures

ICS
CCS: P20
发布: 1993-01-01
实施

BOCA CHAPTER 20 NFPC COMM-1993 帐篷和空中支援的结构

The following is a listing of the standards referenced in this code, the effective date of the standard, the promulgating agency of the standard and the section(s) of this code that refer to the standard.

Tents and Air-Supported Structures

ICS
CCS: P20
发布: 1993-01-01
实施

BOCA CHAPTER 34 NBC COMM V2-1993 现有的结构

This eleventh edition presents the code as originally issued, with changes approved through 1989, and with certain editorial changes made to maintain the sequence of the code, to standardize the format of all 1990 BOCA National Codes, and to update the

Existing Structures

ICS
CCS: P20
发布: 1993-01-01
实施

BOCA CHAPTER 34 NBC-1993 现有的结构

Existing Structures

ICS
CCS: P20
发布: 1993-01-01
实施

BOCA CHAPTER 17 NBC COMM V2-1993 结构试验和检查

Structural Tests and Inspections

ICS
CCS: P20
发布: 1993-01-01
实施

BOCA CHAPTER 17 NBC-1993 结构试验和检查

Structural Tests and Inspections

ICS
CCS: P20
发布: 1993-01-01
实施

ANSI/ASTM E783:1993 穿过安装的外窗和门的空气泄漏现场测量的试验方法

This test method provides a field procedure for determining the air leakage rates of installed exterior windows and doors. This test method is applicable to exterior windows and doors and is intended to measure only such leakage associated with the assembly and not the leakage through openings between the assemblies and adjacent construction. The test method can be adapted for the latter purpose, provided the potential paths of air movement and the sources of infiltration and exfiltration can be identified, controlled, or eliminated. This test method attempts to create and given set of natural environmental conditions. There is a strong possibility that the test method or the test apparatus may, by virtue of their design and use, induce air leakage that does not occur under natural environmental exposure. This test method is intended for the field testing of installed exterior windows or doors. Persons interested in laboratory testing of fenestration products should reference Test Method E283. Persons using this procedure should be knowledgeable in the area of fluid mechanics and instrumentation practices, and shall have a general understanding of fenestration products and components. Throughout this test method, SI units are listed first in accordance with E-6 metric policy, and shall be considered the primary units. Non-SI units are provided in parenthesis. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 7.

Test Method for Field Measurement of Air Leakage Through Installed Exterior Windows and Doors (04.11)

ICS: 91.060.50
CCS: P20
发布: 1993
实施: 1996-10-02

ASTM D4319-93 用短期分批法测定分配比的标准试验方法

1.1 This test method covers the determination of distribution ratios of chemical species for site-specific geological media by a batch sorption technique. It is a short-term laboratory method primarily intended for ionic species subject to migration in granular porous material, and the application of the results to long-term field behavior is not known. Distribution ratios for radionuclides in selected geomedia are commonly determined for the purpose of assessing potential migratory behavior at waste repositories. This test method is also applicable to studies of intrusion waters and for parametric studies of the effects of variables and of mechanisms which determine the measured distribution ratios.1.2 The values stated in acceptable metric units are to be regarded as the standard.1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Distribution Ratios by the Short-Term Batch Method