Q04 基础标准与通用方法 标准查询与下载

JIS A 1470-1:2002 调节室内湿度的建筑材料的吸湿或脱湿的试验方法.第1部分:湿度的反应方法

この規格は，湿度変動による調湿建材の吸放湿性の試験方法について規定する。備考 調湿建材とは，内装材などとして使用し，主として室内などの対象空間の相対湿度変動を緩和するために用いられる建築材料である。なお，この測定法は，一般建築材料を評価するためにも用いることができる。

Test method of adsorption/desorption efficiency for building materials to regulate an indoor humidity -- Part 1: Response method of humidity

JIS A 1470-2:2002 调节室内湿度的建筑材料的吸湿或脱湿的试验方法.第2部分:密封箱法

この規格は，調湿建材を入れた密閉箱の温度変動による調湿建村の吸放湿性の試験方法について規定する。 備考 調湿建材とは内装材などとして使用し，主として室内などの対象空間の相対湿度変動を緩和するために用いられる建築材料である。なお。この測定法は，一般建築材料を評価するためにも用いることができる。

Test method of adsorption/desorption efficiency for building materials to regulate an indoor humidity -- Part 2: Sealed box method

ISO 15686-3:2002 房屋和建筑资产.服务年限计划.第3部分:性能审核和检验

This part of ISO 15686 is concerned with ensuring the effective implementation of service life planning. It describes the approach and procedures to be applied to pre-briefing, briefing, design, construction and, where required, the life care management and disposal of buildings and constructed assets to provide a reasonable assurance that measures necessary to achieve a satisfactory performance over time will be implemented. The cost implications of service life planning and the broader issues of sustainability (e.g. embodied energy, land use) are not developed in this part of ISO 15686. NOTE Throughout this part of ISO 15686 the term "constructed asset" is used to include buildings; infrastructure works such as roads, bridges and pipelines; structural works such as communications masts; and other engineering works such as power stations and chemical plants.

Building and constructed assets - Service life planning - Part 3: Performance audits and reviews

DIN EN 424:2002 弹性地板覆盖物.模拟家具腿移动效应测定

The project specifies a method for determining the resistance of an installed resilient floor covering to the mechanical stress resulting from the movement of a furniture leg.

Resilient floor coverings - Determination of the effect of simulated movement of a furniture leg; German version EN 424:2001

ASTM C918-02 测量早期抗压强度推测出后期抗压强度的标准试验方法

1.1 This test method covers a procedure for making and curing concrete specimens and for testing them at an early age. The specimens are stored under standard-curing conditions and the measured temperature history is used to compute a maturity index that is related to strength gain. 1.2 This test method also covers a procedure for using the results of early-age compressive-strength tests to project the potential strength of concrete at later ages.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measuring Early-Age Compressive Strength and Projecting Later-Age Strength

ASTM F34-02 柔性阻挡材料液体提取物试验池结构的标准实施规程

1.1 This practice covers the construction of test cells which may be used for the extraction of components from flexible barrier materials by suitable extracting liquids, including foods and food simulating solvents.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials

ASTM E329-02 建筑用材料的试验和/或检查机构的标准规范

1.1 This specification defines the minimum requirements for inspection agency personnel or testing agency laboratory personnel, or both, and the minimum technical requirements for equipment and procedures utilized in the testing and inspection of materials used in construction. 1.2 Criteria is provided for evaluating the capability of agency to properly perform designated tests on construction materials, and establishes essential characteristics pertaining to the organization, personnel, facilities, and quality systems of the agency. This practice may be supplemented by more specific criteria and requirements for particular projects. 1.3 This specification can be used as a basis to evaluate an agency and is intended for use in qualifying and/or accrediting agencies, public or private, engaged in the testing and inspection of construction materials. These materials include concrete, steel, soil, masonry and bituminous materials.

Standard Specification for Agencies Engaged in the Testing and/or Inspection of Materials Used in Construction

ASTM F34-02(2007) 柔性阻挡材料液体提取物试验池结构的标准实施规程

Knowledge of extractives from flexible barrier materials may serve many useful purposes. A test cell constructed as described in this practice may be used for obtaining such data. Another test cell has been found equivalent to the one described in this practice. See the appendix for the source of the alternate cell.1.1 This practice covers the construction of test cells which may be used for the extraction of components from flexible barrier materials by suitable extracting liquids, including foods and food simulating solvents.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Construction of Test Cell for Liquid Extraction of Flexible Barrier Materials

ASTM D3665-02 建筑材料的随机采样的标准实施规程

1.1 This practice covers the determination of random locations (or timing) at which samples of construction materials can be taken. For the exact physical procedures for securing the sample, such as a description of the sampling tool, the number of increments needed for a sample, or the size of the sample, reference should be made to the appropriate standard method. The selection procedures in Section utilize the table of four-digit numbers given in Table 1.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Random Sampling of Construction Materials

ASTM D6024-02 用球落在可控制的低强度材料上的方法测定荷载适用性的标准试验方法

This test method is used primarily as a field test to determine the readiness of the CLSM to accept loads prior to adding a temporary or permanent wearing surface. This test method is not meant to predict the load bearing strength of a CLSM mixture. This test is one of a series of quality control tests that can be performed on CLSM during construction to monitor compliance with specification requirements. The other tests that can be used during construction control are Test Methods D 4832, D 6023, and D 6103. Note 18212;The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/and the like. Users of this standard are cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3470 provides a means of evaluating some of those factors.1.1 This specification explains the determination of the ability of Controlled Low Strength Material (CLSM) to withstand loading by repeatedly dropping a metal weight onto the in-place material.1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.1.2.1 The method used to specify how data are collected, calculated, or recorded in this test method is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope.1.3 The values stated in SI units are to be regarded as the standard. The inch-pound equivalents are shown for information only.1.4 CLSM is also known as flowable fill, controlled density fill, soil-cement slurry, soil-cement grout, unshrinkable fill," K-Krete," and other similar names.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application

DIN EN 13238:2001 建材着火试验反应.基材选择调节方法和通则

Reaction to fire tests for building products - Conditioning procedures and general rules for selection of substrates; German version EN 13238:2001

DIN EN ISO 12572:2001 建筑材料和产品湿热性能.水蒸汽传输特性测定

The document specifies a method based on cup tests for determining the steady state water vapour transmission rate, water vapour permeance and water vapour permeability of building materials. Different sets of test conditions are specified. The general principles are applicable to all building materials, including those with integral skins and adhered facings. Five annexes give details of test methods suitable for different material types. The results obtained by this method are suitable for design purpose, production control and for inclusion in product specifications.#,,#

Hygrothermal performance of building materials and products - Determination of water vapour transmission properties (ISO 12572:2001); German version EN ISO 12572:2001

BS EN ISO 12572:2001 建筑材料和产品的湿温性能.水蒸气传输性能的测定

This standard specifies a method based on cup tests for determining the water vapour permeance of building products and the water vapour permeability of building materials under isothermal conditions. Different sets of test conditions are specified. The general principles are applicable to all hygroscopic and non hygroscopic building materials and products, including those with facings and integral skins. Annexes give details of test methods suitable for different material types. This standard is not applicable in the case of test specimens with water vapour diffusion-equivalent air layer thickness values less than 0,1 m, as a result of increasing uncertainty in the measurement results. If the measured water vapour diffusion-equivalent air layer thickness is greater than 1500 m the material can be considered impermeable. The results obtained by this method are suitable for design purposes, production control and for inclusion in product specifications.

Hygrothermal performance of building materials and products - Determination of water vapour transmission properties

ISO 12572:2001 建筑材料和制品湿热性能 水蒸气扩散特性的测定

This standard specifies a method based on cup tests for determining the water vapour permeance of building products and the water vapour permeability of building materials under isothermal conditions. Different sets of test conditions are specified. The general principles are applicable to all hygroscopic and non hygroscopic building materials and products, including those with facings and integral skins. Annexes give details of test methods suitable for different material types. This standard is not applicable in the case of test specimens with water vapour diffusion-equivalent air layer thickness values less than 0,1 m, as a result of increasing uncertainty in the measurement results. If the measured water vapour diffusion-equivalent air layer thickness is greater than 1500 m the material can be considered impermeable. The results obtained by this method are suitable for design purposes, production control and for inclusion in product specifications.

Hygrothermal performance of building materials and products - Determination of water vapour transmission properties

DIN EN 12664:2001 建筑材料和产品的热性能.用保温板和热流计测定耐热性.中等耐热性和低耐热性干燥产品和潮湿产品

Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products with medium and low thermal resistance; German version EN 12664:2001

DIN EN 12667:2001 建筑材料和产品热性能.用保温板和热流计测定耐热性.高耐热性和中等耐热性产品

Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance; German version EN 12667:2001

BS EN 12667:2001 建筑材料和产品的热性能.用护热板和热流计的方法测定热阻.高和中耐热的产品

This standard specifies principles and testing procedures for determining, by means of the guarded hot plate or heat flow meter methods, the thermal resistance of test specimens having a thermal resistance of not less than 0,5 m·K/W NOTE 1 The above limit is due to the effect of contact thermal resistances. An upper limit for measurable thermal resistance depends upon a number of factors described in this standard, but a unique figure cannot be assigned. It applies in principle to any mean test temperature, but the equipment design in annex D is essentially intended to operate between a minimum cooling unit temperature of -100 ℃ and maximum heating unit temperature of +100 ℃. NOTE 2 Limits to the mean test temperature are only imposed by the materials used in the apparatus construction and by ancillary equipment. It supplies additional limits for equipment performance and test conditions. It does not supply general equipment design procedures, equipment error analysis, equipment performance check or the assessment of equipment accuracy. It supplies example designs of equipment complying with the requirements set down in this standard. This standard does not supply general guidance and background information (e.g. the heat transfer property to be reported, product-dependent specimen preparations, procedures requiring multiple measurements, such as those to assess the effect of specimen non-homogeneities, those to test specimens whose thickness exceeds the apparatus capabilities, and those to assess the relevance of the thickness effect). Due to these limitations, this standard should be used in conjunction with the product standard relevant to the product to be tested. Although intended primarily for building materials, it can also be used for specimens of any material that conforms to the requirements specified. This standard does not cover measurements on moist products of any thermal resistance or measurements on thick products of high and medium thermal resistance.

Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance

BS EN 12664:2001 建筑材料和产品的热性能.用护热板和热流计的方法测定热阻.中和低热阻的干和湿产品

This European Standard defines minimum structural requirements for railway vehicle bodies. This European Standard specifies the loads vehicle bodies shall be capable of sustaining, identifies how material data shall be used and presents the principles to be used for design verification by analysis and testing. The railway vehicles are divided into categories which are defined only with respect to the structural requirements of the vehicle bodies. These structural requirements should not be confused with operating requirements. It is the responsibility of the operator to decide as to which structural category railway vehicles shall be designed. Some vehicles may not fit into any of the defined categories; the structural requirements for such railway vehicles should be specified by the operator using the principles presented in this European Standard. The standard applies to all railway vehicles within the EU and EFTA territories. The specified requirements assume operating conditions and circumstances such as are prevalent in these countries.

Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Dry and moist products of medium and low thermal resistance

NF P50-761*NF EN 12939:2001 建筑材料和产品的热性能.用防护热板和热流量计法测定热阻.厚产品的高热阻和中热阻

Thermal performance of building materials and products - Determination of thermal resistande by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance.

DIN EN 12939:2001 建筑材料和产品热性能.用防护热板和热流量计测定热阻.厚产品的高热阻和中热阻

The document gives the procedures to determine the thermal resistance of products at thicknesses that exceed 100 mm for guarded hot plate or heat flow meter. It supplies guidelines to assess the relevance of the thickness effect, i.e. to establish whether the thermal resistance of a thick product can or cannot be calculated as the sum of the thermal resistances of slices cut from the product. It does not supply information either general or on the use of interpolation equations in the measurement of thick specimens. The procedures described are based on guarded hot plates or heat flow meter apparatus.#,,#

Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Thick products of high and medium thermal resistance; German version EN 12939:2000