Q04 基础标准与通用方法 标准查询与下载

BHMA A156.28-2000 锁系统建议措施

This Standard contains requirements for door closers surface mounted, concealed in the door, overhead concealed and concealed in the floor. Also included are pivots for floor closers. Criteria for conformance include cycle, operational, closing force and finish tests. Optional tests which shall be specified separately are also included.

Recommended Practices for Keying Systems

ASTM E2110-00 外部绝缘和精整系统的标准术语

1.1 This terminology consists of terms and definitions pertaining to materials and processes used in the design and application of exterior insulation and finish systems (EIFS).

Standard Terminology for Exterior Insulation and Finish Systems (EIFS)

GA 236-2000 极端的天气条件下的联合治疗

Although extreme environmental conditions have little effect on the process of applying gypsum board, special procedures or precautions should be observed during the application and drying of joint compounds and adhesives. When weather conditions are extreme, either hot, cold, humid, or dry, the drying times of joint treatment materials are affected. Hot, dry weather accelerates drying; cold weather slows drying and increases the risk of freezing; wet or humid weather slows drying. Weather shifts from one extreme to another can cause movement in wood framing (moisture related) or in steel framing (temperature related) which can have an effect on the final appearance of any given project.

JOINT TREATMENT UNDER EXTREME WEATHER CONDITIONS

ASTM C1067-00(2007) 建筑材料试验方法的耐久或屏蔽程序实施的标准实施规程

1.1 This practice covers a procedure for detecting sources of variation in a test method. The procedure should be used during the development of a test method, before the interlaboratory study is executed, such as those in Practices C 670, C 802, and E 691. Interlaboratory studies can be expensive to execute. Resources will probably be more efficiently used if sources of variation in a test method are eliminated prior to performing the interlaboratory study. The procedure also is useful for determining sources of variation in an existing test method that has been found to have poor precision.1.2 This practice covers, in very general terms, techniques for planning, collecting data, and analyzing results from a few laboratories. provides the details of the procedure with an example and gives the theoretical background.1.3 The practice does not give information pertinent to estimating within- or between-laboratory precision.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Conducting A Ruggedness or Screening Program for Test Methods for Construction Materials

ASTM C1067-00 建筑材料试验方法的耐久或屏蔽程序实施的标准实施规程

1.1 This practice covers a procedure for detecting and reducing sources of variation in a test method early in its development and prior to an interlaboratory study. One of the main purposes of the procedure, by means of a ruggedness or screening program, is the elimination of test methods that exhibit poor precision even after vigorous efforts to reduce their variability. 1.2 This practice covers, in very general terms, techniques for planning, conducting, and analyzing results from a few laboratories to establish whether a well written test method is good enough to justify an interlaboratory study. Annex A1 provides the details of the procedure with an example and Annex A2 gives the theoretical background. 1.3 This practice is intended to be used before spending the time and money required to conduct a full scale interlaboratory study, such as those in Practices C670, C802, or E691. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Conducting A Ruggedness or Screening Program for Test Methods for Construction Materials

ISO 10456:1999 建筑材料和制品 确定热性能申报值和设计值的程序

This International Standard specifies methods for the determination of declared and design thermal values for thermally homogeneous building materials and products. It also gives procedures to convert values obtained under one set of conditions to those valid for another set of conditions. These procedures are valid for design ambient temperatures between -30 ℃ and +60 ℃. Conversion coefficients for temperature, valid for mean temperatures between 0 ℃ and 30 ℃, and moisture are given in annex A. This International Standard does not give any conversion coefficients for the effect of ageing or other effects like convection or settlement.

Building materials and products - Procedures for determining declared and design thermal values

BS EN 1946-3:1999 建筑产品和元件热性能.试验室测量热传递性能评估的特殊标准.用热流量计法测量

This part 3 of this standard provides specific technical criteria for the assessment of laboratories to undertake steady-state heat transfer property measurements by the heat flow meter method according to prEN 12667 and prEN 12664. It complements the common criteria in part 1. Guidance is given on the organization and contents of the equipment manual, the calibration and maintenance files and the measurement procedure document. It provides information on mandatory equipment performance specifications, equipment description and on calculations for the equipment design and error analysis. It provides information on experimental procedures suitable for the assessment of equipment accuracy.

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Measurements by heat flow meter method

BS EN 1946-2:1999 建筑产品和元件热性能.试验室测量热传递性能评估的特殊标准.用保护热平板法测量

This part 2 of this standard provides specific technical criteria for the assessment of laboratories to undertake steady-state heat transfer property measurements by the guarded hot plate method according to prEN 12667 and prEN 12664. It complements the common criteria in part 1. Guidance is given on the organization and contents of the equipment manual, the calibration and maintenance files and the measurement procedure document.It provides information on mandatory equipment performance specifications, equipment description and on calculations for the equipment design and error analysis. It provides information on experimental procedures suitable for the assessment of equipment accuracy.

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Measurements by guarded hot plate method

BS EN 1946-1:1999 建筑产品和元件热性能.试验室测量热传递性能评估的特殊标准.一般标准

This standard gives specific technical criteria to be used within the frame of the general criteria given in EN 45001 and EN 45002 for the assessment of laboratories performing heat transfer property measurements of building products and components according to standardized test methods. It is relevant both to assessments conducted internally and to those carried out formally by an accreditation body, and is intended to be of assistance to all interested parties. It gives contents of the documentation required by EN 45001 (equipment manual, calibration and maintenance files, measurement procedure document) and the procedures for the assessment of equipment accuracy and performance check. All other requirements regarding laboratories undertaking heat transfer property measurements are given in the EN 45000 series. This part 1 of this standard gives assessment requirements common to various test methods; the subsequent parts give assessment requirements, which are relevant to each test method The application of this standard assumes an adequate level of competence for the personnel involved.

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Common criteria

DIN EN 1946-3:1999 建筑产品和建筑部件热性能.热传导性能实验室评估专用准则.第3部分:热流测量平板仪法

The document provides specific technical criteria for the assessment of laboratories to undertake steady-state heat transfer property measurements by the heatflow meter method. It complements the common criteria in DIN EN 1946-1. Guidance is given on the organization and contents of the equipment manual, the calibration and maintenance files and the measurement procedure document. It provides information on mandatory equipment performance specifications, equipment description and on calculations for the equipment design and on error analysis. It provides information on experimental procedures suitable for assessment of equipment accuracy.

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 3: Measurements by the guarded heat flow meter method; German version EN 1946-3:1999

DIN EN 1946-2:1999 建筑产品和建筑部件热性能.热传导性能实验室评估专用准则.第2部分:平板仪法测量

The document provides specific technical criteria for the assessment of laboratories to undertake steady-state heat transfer property measurements by the guarded hot plate method. It complements the common criteria in DIN EN 1946-1. Guidance is given on the organization and contents of the equipment manual, the calibration and maintenance files and the measurement procedure document. It provides information on mandatory equipment performance specifications, equipment description and on calculations for the equipment design and on error analysis. It provides information on experimental procedures suitable for assessment of equipment accuracy.

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 2: Measurements by the guarded hot plate method; German version EN 1946-2:1999

DIN EN 1946-1:1999 建筑产品和建筑部件的热性能.热传导性能实验室评估专用准则.第1部分:通用准则

Thermal performance of building products and components - Specific criteria for the assessment of laboratories measuring heat transfer properties - Part 1: Common criteria; German version EN 1946-1:1999

DB37/T 266-1999 建材产品中废渣掺加量的测定方法 X射线荧光分析法

本标准规定了建材产品、半成品中煤矸石、石煤、煤泥、粉煤灰、锅炉炉渣、硼尾矿粉、硫铁矿渣等工业废渣掺加量的测定方法，适用于水泥、水泥生料和烧结建材制品配料，其他建材制品可参照本标准执行。

X-ray fluorescence analysis method for the determination of the amount of waste slag added in building material products

BOCA CHAPTER 2 NBC-1999 定义

The format and provisions of The BOCA National Propero Maintenance Code are designed to provide units of government with an effective regulatory means of providing minimum health and safety requirements for existing buildings and structures.

Definitions

BOCA CHAPTER 3 NBC-1999 使用或占用

The format and provisions of The BOCA National Propero Maintenance Code are designed to provide units of government with an effective regulatory means of providing minimum health and safety requirements for existing buildings and structures.

Use or Occupancy

BOCA CHAPTER 44 NFPC-1999 参照标准

The BOCA National Mechanical Code was initially prepared and updated on the premise that adequate code requirements are essential to the safe installation and maintenance of all mechanical equipment and systems in order to protect the public health, sa

Referenced Standards

BOCA CHAPTER 2 NFPC-1999 定义

The following is a listing of the standards referenced in this code, the effective date of the standard, the promulgating agency of the standard and the section(s) of this code that refer to the standard.

Definitions

BOCA CHAPTER 35 NBC-1999 参照标准

It shall be unlawful to interfere with, attempt to interfere with, conspire to interfere with, obstruct or restrict the mobility of or block the path of travel of any fire department emergency vehicle in any way, or to interfere with, attempt to inter

Referenced Standards

ASTM D3665-99 结构材料的随机采样

1.1 This practice covers the determination of random locations (or timing) at which samples of construction materials can be taken. For the exact physical procedures for securing the sample, such as a description of the sampling tool, the number of increments needed for a sample, or the size of the sample, reference should be made to the appropriate standard method. The selection procedures in Section 4 utilize the table of three-digit numbers given in Table 1. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are for information only. 1.3. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Random Sampling of Construction Materials

ASTM D6485-99(2004) 从层面排放的挥发性有机化学物质短期照射的强烈的刺激作用的风险特征的标准指南

The objective of this guide is to describe procedures and data sources for conducting risk characterization of acute inhalation exposure to chemicals emitted from bedding sets. Risk characterization can be used to identify chemical(s) that pose potentially significant human health risks for the scenario(s) and population(s) selected for exposure assessment. Such identification of chemicals can help in identifying the components or materials used in manufacture of bedding sets that should be further examined. Risk characterization also includes an assessment of potential odor problems for any individual chemical emitted by the bedding set.1.1 This guide provides guidance to individuals and organizations for conducting risk characterization of exposure to volatile organic chemicals (VOCs) emitted from bedding sets or an ensemble of a mattress and supporting box spring.1.2 This guide is for risk characterization of short-term exposures to a new bedding set brought into a residential indoor environment. The risk characterization considerations presented in this guide are applicable to both the general population and sensitive subgroups, such as convalescing adults.1.3 The risk characterization addressed in this guide is limited to acute health and irritation effects resulting from short-term exposure to VOCs in indoor air. Although certain procedures described in this guide may be applicable to assessing long-term exposure, the guide does not address cancer and other chronic health effects.1.4 VOC emissions from bedding sets, as in the case of other household furnishings, usually are highest when the products are new. A used bedding set may also emit VOCs, either from the original materials or as a result of its use. The procedures presented in this guide also are applicable to used bedding sets.1.5 Risk characterization procedures described in this guide should be carried out under the supervision of a qualified toxicologist or risk assessment specialist, or both.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use.

Standard Guide for Risk Characterization of Acute and Irritant Effects of Short-Term Exposure to Volatile Organic Chemicals Emitted from Bedding Sets