Q13 混凝土、集料、灰浆、砂浆 标准查询与下载
共找到 2793 条与 混凝土、集料、灰浆、砂浆 相关的标准，共 187 页
Lightweight aggregates; German version EN 13055:2016
- ICS
- 91.100.15
- CCS
- Q13
- 发布
- 2016-11
- 实施
Methods of testing cement - Part 10: Determination of the water-soluble chromium (VI) content of cement; German version EN 196-10:2016
- ICS
- 91.100.10
- CCS
- Q13
- 发布
- 2016-11
- 实施
Prefabricated reinforced components of autoclaved aerated concrete
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-10-31
- 实施
- 2016-10-31
Melt-solidified slag aggregate for concrete derived from municipal solid waste and sewage sludge
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-10-20
- 实施
Electrochemical realkalization and chloride extraction treatments for reinforced concrete - Part 1: Realkalization; German version EN 14038-1:2016
- ICS
- 91.080.40
- CCS
- Q13
- 发布
- 2016-10
- 实施
Electrochemical realkalization and chloride extraction treatments for reinforced concrete. Realkalization
- ICS
- 91.080.40
- CCS
- Q13
- 发布
- 2016-08-31
- 实施
- 2016-08-31
Test methods for polymer-modified mortar
- ICS
- 91.100.10
- CCS
- Q13
- 发布
- 2016-08-22
- 实施
Phenolic board bonding and plastering mortar for external wall insulation
- ICS
- 91.100.10
- CCS
- Q13
- 发布
- 2016-07-11
- 实施
- 2017-01-01
Recycled concrete using recycled aggregate Class L (Amendment 1)
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-04-20
- 实施
Recycled concrete using recycled aggregate class M (Amendment 1)
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-04-20
- 实施
Slag aggregate for concrete -- Part 2: Ferronickel slag aggregate
- ICS
- 91.100.15;91.100.99
- CCS
- Q13
- 发布
- 2016-04-20
- 实施
Slag aggregate for concrete -- Part 3: Copper slag aggregate
- ICS
- 91.100.15;91.100.99
- CCS
- Q13
- 发布
- 2016-04-20
- 实施
Recycled aggregate for concrete-class H (Amendment 1)
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-04-20
- 实施
本标准规定了榫接混凝土砖和砌块的术语和定义、分类、原材料、技术要求、试验方法、检验规则、产品合格证、包装和贮运。 本标准适用于民用与工业建筑的自承重墙体、中空墙体、中空灌芯复合墙体和其它砌体等工程用的榫接混凝土砖和砌块。
Mortise and Mortise Concrete Bricks and Blocks
- ICS
- 91.100.30
- CCS
- Q13
- 发布
- 2016-03-07
- 实施
- 2016-06-07
本标准规定了同步注浆用干混砂浆的术语和定义、基本规定、技术指标、配合比设计、施工、质量检验与验收。 本标准适用于同步注浆用干混砂浆在隧道盾构法施工中的应用。
Technical Specification for Application of Dry-mixed Synchronous Grouting Mortar
- ICS
- 91.100.10
- CCS
- Q13
- 发布
- 2016-02-29
- 实施
- 2016-06-01
本规程适用于喷射混凝土的材料选择、设计、配合比计算、施工及验收。
Technical specification for application of sprayed concrete
- ICS
- CCS
- Q13
- 发布
- 2016-02-22
- 实施
- 2016-08-01
1.1 This specification covers deformed and plain low-carbon, chromium, steel bars, in cut lengths and coils for concrete reinforcement. These bars are furnished in three alloy types depending on the chromium range content. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1.2 (A) The nominal dimensions of a deformed bar are equivalent to those of a plain round bar having the same weight [mass] per foot [metre] as the deformed bar. 1.2 Bars are of two minimum yield strength levels as defined in 9.2: namely, 1008201;000 psi [690 MPa], and 1208201;000 psi [830 MPa] designated as Grade 100 [690] and Grade 120 [830], respectively. 1.3 Bars are furnished to three different chemical compositions, designated as Alloy Type CL, CM, and CS. Chemical compositions are shown in Table 2. (A) Maximum unless range is indicated; percentages refer to weight [mass] percentages. 1.4 Plain bars, in sizes up to and including 2.25 in. [57.2 mm] 21/2 in. [63.5 mm] in diameter in coils and cut lengths, when ordered shall be furnished under this specification in Grade 100 [690] and Grade 120 [830]. For ductility properties (elongation and bending), test provisions of the nearest smaller nominal diameter deformed bar size shall apply. Requirements providing for deformations and marking shall not be applicable. Note 1: Welding of the material in this specification should be approached with caution since no specific provisions have been included to enhance its weldability. When this steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used. 1.5 Requirements for alternate bar sizes are presented in Annex A1. The requirements in Annex A1 only apply when specified by the purchaser (see 4.2.4). 1.6 A supplementary requirement (S1) is provided for use where bend testing of bar designation Nos. 14 and 18 [43, 57], and bar designation Nos. 40, 50, and 60 in Annex A1, is required by the purchaser. The supplementary requirement applies only when specified in the purchase order. 1.7 The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification. ......
Standard Specification for Deformed and Plain, Low-Carbon, Chromium, Steel Bars for Concrete Reinforcement
- ICS
- 77.140.15
- CCS
- Q13
- 发布
- 2016
- 实施
