Q15 墙体材料 标准查询与下载

BS 8297:2000 无负荷预制混凝土护板设计和安装实用规程

Recommendations for the design, manufacture and installation of concrete cladding used to cover structural framework. Guidance is given on precautions that have to be taken to provide for permanent and temporary movements, peak gust wind loading, design of joints methods of attachment, surface finish, on-site erection, fixing and performance testing.

Code of practice for Design and installation of non-loadbearing precast concrete cladding

BS EN 12179:2000 幕墙.抗风性.试验方法

This standard defines the method for determining the resistance to wind load of curtain walling, both its fixed and openable parts, under postive and negative static air pressure. NOTE This standard applies to any curtain walling product as defined in prEN 13830:2000.

Curtain walling - Resistance to wind load - Test method

BS EN 772-20:2000 圬工砌块的试验方法.圬工单位表面平整度的测定.

This European Standard specifies a method for determining the flatness of surfaces of masonry units.

Methods of test for masonry units - Determination of flatness of faces of masonry units

JC 862-2000 粉煤灰小型空心砌块

Fly ash small hollow block

BS EN 846-8:2000 圬工辅助砌块的试验方法.小梁吊架的负载容量和负载偏转特性的测定

This European Standard specifies a method for determining the strength and load-deflection characteristics of joist hangers fixed to a masonry wall and supporting a timber joist.

Methods of test for ancillary components for masonry - Determination of load capacity and load-deflection characteristics of joist hangers

BS EN 13527:2000 百叶窗和遮帘.操纵力的测量.试验方法

The present standard defines the test methods to be carried out to determine the operating force required for shutters and blinds. It applies to the following products: - Internal blinds: internal Venetian, roller, vertical and pleated blinds. - External blinds: Folding arm awning, trellis arm awning, vertical roller awning, pivot arm awning, marquisolette, facade awning, roof light awning, verandah awning or conservatory awning, Dutch awning, insect screen awning, louvre array. - Shutters: External Venetian blind, roller shutter (vertical or projected) Venetian shutter (vertical or projected), flat-closing concertina shutter, concertina shutter, sliding panel shutter). Shutters with a projection system are also covered. The test described establish the effort or force necessary to result - in the movement or displacement of the curtain during both extension and retraction - to project shutters, - to tilt laths.

Shutters and blinds - Measurement of operating force - Test methods

ASTM C652-00a 空心砖(用粘土或页岩制空心砌块)标准规范

1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion. Four types of hollow brick in each of two grades and two classes are covered. In this specification the term hollow brick shall be understood to mean hollow clay masonry units whose net cross-sectional area (solid area) in any plane parallel to the surface, containing the cores, cells, or deep frogs, is less than 75 % of its gross cross-sectional area measured in the same plane (see 3.3). This specification does not cover brick intended for use as paving brick (see Specification C902).1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this standard.1.3 Brick covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See "firing" and "firing bond" in Terminology C43.)1.4 Hollow brick differ from unglazed structural clay tile (Specifications C34 and C212) and solid brick (Specifications C62 and C216). Hollow brick require greater shell and web thicknesses and higher minimum compressive strength than structural clay tile, but permit greater void area and lesser distance from exposed edge to core hole than solid brick. Therefore, environmental and structural performance may be different in elements constructed of hollow brick from those constructed of structural clay tile or solid brick.1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

ASTM C62-00 砌砖(用粘土或页岩制实心砌块)标准规范

1.1 This specification covers brick intended for both structural and nonstructural masonry where external appearance is not a requirement. The brick are prismatic units available in a variety of sizes, shapes, textures, and colors. The specification does not cover brick intended for use as facing units or where surface appearance is a requirement, (see Specification C216). This specification does not cover brick intended for use as paving brick (see Specification C902).1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 3) of this standard is beyond the scope of this standard.1.3 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing, fired bond, and incipient fusion in Terminology C43.)1.4 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick (see Terminology C43).1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale)

ASTM A951-00 砌砖连接增强的标准规范

1.1 This specification covers masonry joint reinforcement fabricated from cold drawn steel wire. Joint reinforcement consists of longitudinal wires welded to cross wires. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Masonry Joint Reinforcement

ASTM C1106-00(2012) 碳砖物理特性及耐化学性的标准试验方法

1.1 These test methods are intended for use as short-term tests for evaluating the physical properties of carbon brick and their chemical resistance at various temperatures in immersion service. These test methods provide a means of determining the following changes in the carbon brick specimen and the test media: 1.1.1 Weight, appearance, and compressive strength of the carbon brick specimen. 1.1.2 Appearance of the test media before, during, and after testing of the carbon brick specimen. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Chemical Resistance and Physical Properties of Carbon Brick

ASTM C1372-00 局部挡土墙砌块的标准规范

1.1 This specification covers segmental retaining wall units of concrete, machine-made from portland cement, water, and suitable mineral aggregates with or without the inclusion of other materials. The units are intended for use in the construction of mortarless segmental retaining walls.Note 18212;When particular features are desired, such as weight classification, higher compressive strength, surface texture, finish, color, or other special features, such properties should be specified separately by the purchaser. Local suppliers should be consulted as to availability of units having the desired features.1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Segmental Retaining Wall Units

BS EN 1052-2:1999 砖石建筑体的试验方法.挠曲强度的测定

This European Standard specifies a method for determining the flexural strength of small masonry specimens for the two principal axes of loading. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report.

Methods of test for masonry - Determination of flexural strength

JG/T 3063-1999 工业灰渣混凝土空心隔墙条板

本标准规定了工业灰渣混凝土空心隔墙条板的定义、产品分类、要求、检验抽样、试验方法、判定规则及标志、运输和贮存。 本标准适用于民用建筑中作非承重内隔墙用的，以粉煤灰、经煅烧或自燃的煤矸石、炉渣、矿渣、加气混凝土碎屑等工业灰渣为集料制成的混凝土空心条板。 以粉煤灰陶粒和陶砂、页岩陶粒和陶砂、天然浮石等为集料制成的混凝土空心隔坡条板可以参照本标准执行。

Concrete hollow panels contained industrial fly ash and waste slags for partition wall in buildings

JC/T 796-1999 回弹仪评定烧结普通砖强度等级的方法

The method of evaluating the fired common brick strength grading by rebound hammer

BS EN 1052-1:1999 砖石工程的试验方法.压缩强度的测定

This European Standard specifies a method for determining the compressive strength of masonry. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing machine, the method of test, the method of calculation and the contents of the test report.

Methods of test for masonry - Determination of compressive strength

BOCA CHAPTER 18 NBC-1999 地基会及挡土墙

The BOCA National Mechanical Code was initially prepared and updated on the premise that adequate code requirements are essential to the safe installation and maintenance of all mechanical equipment and systems in order to protect the public health, sa

Foundations and Retaining Walls

ASTM C896-99 有关粘土制品的标准术语

Standard Terminology Relating to Clay Products

ASTM C530-99 结构用不承重粘土隔墙砖标准规范

1.1 This specification covers unglazed, structural clay, nonload-bearing screen tile. 1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or non-conformance to the property requirements (Section 5) of this standard is beyond the scope of this standard. 1.3 Tile covered by this standard are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C43). 1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (exluding those in the table and figures) shall not be considered as requirements of the standard.

Standard Specification for Structural Clay Nonloadbearing Screen Tile

ASTM C1420-99 成品砌块投入使用的选择、搬运和送运的标准导则

1.1 This guide covers procedures to facilitate the process of selecting, removing, and shipping of manufactured masonry units that have been placed in usage and are intended for testing. This guide also covers procedures for reporting as part of this process. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Selection, Removal, and Shipment of Manufactured Masonry Units Placed in Usage

ASTM F1066-99 乙烯类合成地板砖标准规范

1.1 This specification covers vinyl composition tile (VCT) with either smooth or embossed surfaces for flooring application. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Vinyl Composition Floor Tile