Q15 墙体材料 标准查询与下载

ASTM C1160-97 耐化学腐蚀炭砖用标准规范

1.1 This specification covers machine made uncored carbon brick produced from low ash calcined petroleum coke, suitable for use in masonry construction which will be exposed to various chemicals. These units are designed primarily for industries using hydrofluoric acid, fluoride salts and high concentrations of alkalies such as sodium and potassium hydroxide. Carbon brick are normally used with carbon filled chemical-resistant mortars. 1.2 This standard does not purport to address the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chemical Resistant Carbon Brick

ASTM C1073-97a 用碱性反应法测定块炉渣水硬效率的标准试验方法

1.1 This test method covers the rapid determination of hydraulic activity of ground-granulated iron blast-furnace slag. This test method measures the accelerated strength development of the slag by using sodium hydroxide solution as mixing water and curing at elevated temperature. 1.2 The values stated in SI units are to be regarded as the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific precautionary statement is given in Section 6.

Standard Test Method for Hydraulic Activity of Ground Slag by Reaction with Alkali

ASTM C1160-97(2003) 耐化学腐蚀炭砖用标准规范

1.1 This specification covers machine made solid uncored carbon brick produced from either metallurgical or petroleum calcined coke, baked to a minimum 1850176;F (1010176;C), and suitable for use in masonry construction which will be exposed to various chemicals. These units are designed primarily for industries using hydrofluoric acid, fluoride salts, and high concentrations of alkalies such as sodium and potassium hydroxide. Carbon brick are normally used with carbon filled chemical-resistant mortars.1.2 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chemical-Resistant Carbon Brick

ASTM C1160-97(2008) 耐化学腐蚀炭砖用标准规范

1.1 This specification covers machine made solid uncored carbon brick produced from either metallurgical or petroleum calcined coke, baked to a minimum 1850°F (1010°C), and suitable for use in masonry construction which will be exposed to various chemicals. These units are designed primarily for industries using hydrofluoric acid, fluoride salts, and high concentrations of alkalies such as sodium and potassium hydroxide. Carbon brick are normally used with carbon filled chemical-resistant mortars. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Chemical-Resistant Carbon Brick

JC/T 637-1996 蒸压灰砂空心砖

Steam pressure sand lime hollow brick

BOCA CHAPTER 18 NBC-1996 地基会及挡土墙

The BOCA National Mechanical Code was initially prepared and updated on the premise that adequate code requirements are essential to the safe installation and maintenance of all mechanical equipment and systems in order to protect the public health, sa

Foundations and Retaining Walls

ASTM C56-96 结构用粘土非承重砖标准规范

1.1 This specification covers structural clay non-load-bearing tile (partition, fireproofing, and furring). One grade of tile is covered, designated Grade NB.1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or non-conformance to the property requirements (Section 3) of this standard is beyond the scope of this standard.1.3 Tile covered by this standard are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C 43.)1.4 Fireproofing tile intended for use in load-bearing masonry shall conform to Specification C 34.1.5 If tile having a particular color (Note 1), texture, or finish are desired, these features shall be specified separately by the purchaser.Note 18212;Color of tile varies with the type of clay used and degree of burning; hence, it cannot be taken as indicative of classification until after it has been related to absorption by actual tests.1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

Standard Specification for Structural Clay Non-Load-Bearing Tile

ASTM C56-96(2001) 结构用粘土非承重砖标准规范

1.1 This specification covers structural clay non-load-bearing tile (partition, fireproofing, and furring). One grade of tile is covered, designated Grade NB.1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of tile extracted from masonry structures for determining conformance or non-conformance to the property requirements (Section 3) of this standard is beyond the scope of this standard.1.3 Tile covered by this standard are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing and fired bond in Terminology C 43.)1.4 Fireproofing tile intended for use in load-bearing masonry shall conform to Specification C 34.1.5 If tile having a particular color (Note 1), texture, or finish are desired, these features shall be specified separately by the purchaser.Note 18212;Color of tile varies with the type of clay used and degree of burning; hence, it cannot be taken as indicative of classification until after it has been related to absorption by actual tests.1.6 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.

Standard Specification for Structural Clay Non-Load-Bearing Tile

ASTM C687-96 松散填充型建筑材料热阻的测定的标准实施规程

1.1 This practice presents a laboratory guide to determine the thermal resistance of loose-fill building insulations at mean temperatures between -20 and 55176C (-4 to 131176F). 1.2 This practice applies to a wide variety of loose-fill thermal insulation products including fibrous glass, rock/slag wool, or cellulosic fiber materials; granular types including vermiculite and perlite; pelletized products; and any other insulation material that may be installed pneumatically or poured in place. It does not apply to products that change their character after installation either by chemical reaction or the application of binders or adhesives, nor does it consider the effects of structures, containments, facings, or air films. 1.3 Since this practice is designed for reproducible product comparison, it measures the thermal resistance of an insulation material which has been preconditioned to a relatively dry state. Consideration of changes of thermal performance of a hygroscopic insulation by sorption of water is beyond the scope of this practice. 1.4 The sample preparation techniques outlined in this practice do not cover the characterization of loose-fill materials intended for enclosed applications. For those applications, a separate sample preparation technique that simulates the installed condition will be required. For those applications, however, other aspects of this practice should be applicable. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Thermal Resistance of Loose-Fill Building Insulation

NF P13-307:1995 赤土砖 赤土墙砖 规格和测试方法

Plaquettes en terre cuite - Plaquettes murales en terre cuite - Spécifications et méthodes d'essais.

JIS R 1250:1995 普通砖

Common bricks

BS 493:1995+A1:2010 墙壁通风用通气空心砖和花栅规范

This British Standard specifies requirements for two classes of wall ventilating units as follows: class 1:airbricks for useinexternal walls; class 2: wall ventilators or gratings for internal use. Some typicalexamples of designs are shown in Figure 1,Figure 2 and Figure 3. Other patterns may however be supplied, provided they conform to the requirements of this standard. Guidanceon the information to be supplied by the purchaser when ordering is given in Annex A. Thisstandard contains no requirements for the following properties. Durability (other t hanresistance t o colour change of thermoplastics materials). It is recommended that where there is uncertainty about durability then expert advice should be sought. a) Fire properties s o tf hermoplastics materials. The general useof thermoplastics airbricks, wall ventilators and gratings in isolation in masonry is considered t ohave aninsignificant effect on t he spreadoffire.However, special consideration should begiven to the useof thermoplastics air bricks where it is intended togroup a number of them together, e.g. for boiler house ventilation. b) Compressive strengthof thermoplastics air bricks. The general useof theseinisolation is considered tohave tohave aninsignificant effect on masonry strength. However, special consideration should begiven to their use where it is intended t ogroup a number o ft hem t ogether, e.g. for boiler house ventilation.

Specification for Airbricks and gratings for wall ventilation

BS 493:1995 墙壁通风用通气空心砖和花栅规范

Class 1 units for external use, and class 2 units for internal use, in concrete, clay, copper, aluminium, steel, thermoplastics and plaster (internal only). Overall dimensions, shape of apertures, unobstructed air space, wall hold, screening, testing of plaster units, impact test for thermoplastics airbricks.

Specification for airbricks and gratings for wall ventilation

JIS R 7212:1995 碳块的测试方法

この規格は，主として溶鉱炉及び電気炉の内張り(ライニング)に使用されるカーポンプロックの試験方法について規定する。

Testing methods for carbon blocks

JIS A 6517:1995 建筑物中墙和顶棚用钢制罩饰材料

Steel furrings for wall and ceiling in buildings

BS 8212:1995 采用石膏灰泥板的干襯板和隔墙板实用规程

Recommendations for materials, design backgrounds and insulation of dry lining to walls, ceilings and partitioning. Linings to heated ceilings are excluded.

Code of practice for dry lining and partitioning using gypsum plasterboard

ASTM D5703-95(2007) 粘土砖石工用表面预清洗标准规范

Surface cleaning is necessary to prepare clay brick masonry surfaces for application of coatings intended for water repellent protection. Surface cleaning helps to ensure proper adhesion or even penetration of the coating and to prevent unintended sealing-in of stains. This practice addresses surface cleaning only. Other preparation or remedial repairs, such as repointing the masonry or replacing of units, may be necessary and must be completed prior to application of the water repellent treatment.1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or altering the surface appearance of the clay brick masonry.1.2 Procedures included in this practice are water cleaning, detergent water cleaning, pressurized water cleaning, steam cleaning, and acid cleaning. It is not intended for the cleaning of newly constructed brick masonry. Use of procedures described in this practice may not be appropriate where the surface is of a historical nature.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information see Section 5 and Note 2 and Note 3.

Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry

ASTM C1190-95(2005) 碳酸镁和焙烧浸渍的碱性砖试样配置的标准实施规程

This practice defines a procedure that ensures reasonably consistent preparation of specimens for product testing and evaluation. This practice can be used in the laboratories of producers, users, and general interest parties for research and development or quality control work. It is particularly useful for interlaboratory comparisons on products, for repetitive evaluations or comparisons of products or product quality, and in specifying a uniform preparation practice for specimens for acceptance testing. If pitch impregnated samples are prepared by wet cutting or drilling, care should be taken in drying them. If the samples are heated to facilitate drying, the temperature to which they are heated should not be so high that it causes drainage of pitch from the samples. Porosities of metal-containing brick must be measured using kerosene or mineral spirits because using water will result in an artificially low result. 1.1 This practice covers a procedure for preparing test specimens from magnesia-carbon and impregnated burned basic brick. This practice generally concerns preparation of test specimens from brick greater than 13 in. (33 cm) in length. These brick are mainly manufactured for use in electric arc furnaces and basic oxygen furnaces.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Location of Test Specimens from Magnesia-Carbon and Impregnated Burned Basic Brick

ASTM D5703-95 粘土砖石工用表面预清洗标准规范

1.1 This practice covers non-abrasive surface cleaning of clay brick masonry to remove surface contaminants such as dirt, grease, loose material, soot, fly ash, hydrocarbon residues, algae, etc. in preparation for the application of water repellent coatings without damaging or altering the surface appearance of the clay brick masonry.1.2 Procedures included in this practice are water cleaning, detergent water cleaning, pressurized water cleaning, steam cleaning, and acid cleaning. It is not intended for the cleaning of newly constructed brick masonry. Use of procedures described in this practice may not be appropriate where the surface is of a historical nature.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard information see Section 5 and Note 2 and Note 3.

Standard Practice for Preparatory Surface Cleaning for Clay Brick Masonry

ASTM C1142-95(2013) 砌块用延展寿命的灰浆的标准规格

1.1 This specification covers extended life mortar as delivered for use in construction of non-reinforced or reinforced unit masonry. 1.2 This specification is a property standard. 1.3 Four types of mortar are covered: RM, RS, RN, and RO. These types of mortar can be manufactured by using one of the four mortar formulations with masonry aggregate: portland cement, portland cement-lime, masonry cement, or masonry cement with portland cements. The materials are listed in Section 5. 1.4 Appendix X1 provides a rationale statement and commentary.

Standard Specification for Extended Life Mortar for Unit Masonry