Q18 装修材料 标准查询与下载

JIS A 6921:2003 装修用壁纸和墙面涂料

この規格は，主に建築物の壁，天井などの内装仕上げとして張り付ける壁紙 について規定する。 備考 ここでいう壁紙とは，紙，繊維，無機質材(金属はくを含む。), プラスチックく塩化ビニル樹脂，エチレン酢酸ビニル共重合体樹脂，アクリル樹脂など)及びそれらを組み合わせた壁装用の製品をいう。あらかじめ接着剤，粘着剤などを塗布したものもこの中に含む。

Wallpaper and wallcoverings for decorative finish

JIS A 6909:2003 建筑物纹理精整用涂层材料

この規格は，セメント，合成樹脂などの結合材，顔料，骨材などを主原料とし，主として建築物の内外壁又は天井を，吹付け，ローラー塗り，こて塗りなどによって立体的な造形性をもっ模様に仕上げる建築用仕上塗材(以下,仕上塗材という。)について規定する。

Coating materials for textured finishes of buildings

NF P62-127*NF EN 13893:2003 弹性薄木板和编织地毯.干地板表面摩擦系数测量

Resilient, laminate and textile floor coverings - Measurement of dynamic coefficient of friction on dry floor surfaces.

ASTM D3730-03 高性能结构内墙面饰层试验的标准指南

1.1 This guide covers the selection and use of test methods for high-performance interior architectural wall coatings (HIPAC) that differ from more conventional coatings by being tougher, more stain-resistant, more abrasion-resistant and, ordinarily, designed to be applied to wall surfaces of steel, masonry (poured concrete, concrete block, or cinder block), and plaster or gypsum wallboard. The tests that are listed in are designed to measure performance properties. These tests may not all be required for each HIPAC system. Selection of the test methods to be followed must be governed by experience and the requirements in each individual case, together with agreement between the purchaser and the seller.1.2 High-performance architectural coatings are tough, extra-durable organic coating systems that are applied as a continuous (seamless) film and cure to a hard finish. The finish can be high gloss, semigloss, or low gloss as desired. These coatings are resistant to persistent heat, humidity, abrasion, staining, chemicals, and fungus growth. They are used in areas where humidity, wear, or unusual chemical resistance requirements, particularly to soiling, are required and where strong detergents are used to maintain sanitary conditions. Halls and stairways in public buildings, lavatories, stall showers, locker areas, animal pens, and biological laboratories are typical applications. In addition, food processing plants, dairies, restaurants, schools, and transport terminals frequently use HIPAC systems. These are effective in many areas of building interiors compared with tile and are of low materials and maintenance costs. They are used as a complete system only as recommended by the manufacturer since the individual coats in a system are formulated to be compatible with each other. HIPAC systems should be applied only to properly prepared surfaces such as steel or masonry, including cinder blocks and cement blocks. They can be applied over plaster and gypsum wallboard. Ordinarily, a prime or fill coat, if required, is part of the system.1.3 While they are excellent for walls, HIPAC are not usually intended for ceilings and floors. They would not ordinarily be used in homes, although parents with small children might want to use HIPAC coatings on some walls.1.4 The types of resin ordinarily used are the following: epoxy-polyamide, two-package; polyester-epoxy, two-package; polyurethane, one-package or two-package. However, other resin types are not excluded provided they can meet the requirements (performance specifications) laid down by the purchaser.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement, see the note in 7.6.

Standard Guide for Testing High-Performance Interior Architectural Wall Coatings

ASTM D4977-03 用磨擦法测试矿物涂覆屋顶层颗粒粘结性的标准试验方法

This test method is used to determine the quality of adhesion of the granular surfacing to the coating asphalt in a sample of mineral surfaced roofing. The results determine compliance with the applicable specification requirements or for comparative analysis. This test method applies to “as manufactured” material and may not be applicable to material that has had weathering exposure.1.1 This test method covers the determination of granule adhesion to mineral surfaced roofing due to abrasion.1.2 The values stated in SI units are regarded as standard. The inch-pound units in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

ASTM E648-03 用辐射热能源测定地板包覆材料临界辐射通量的标准试验方法

1.1 This fire-test-response standard covers a procedure for measuring the critical radiant flux of horizontally mounted floor-covering systems exposed to a flaming ignition source in a graded radiant heat energy environment in a test chamber. A specimen is mounted over underlayment, a simulated concrete structural floor, bonded to a simulated structural floor, or otherwise mounted in a typical and representative way.1.2 This fire-test-response standard measures the critical radiant flux at flame-out. It provides a basis for estimating one aspect of fire exposure behavior for floor-covering systems. The imposed radiant flux simulates the thermal radiation levels likely to impinge on the floors of a building whose upper surfaces are heated by flames or hot gases, or both, from a fully developed fire in an adjacent room or compartment. The standard was developed to simulate an important fire exposure component of fires that develop in corridors or exitways of buildings and is not intended for routine use in estimating flame spread behavior of floor covering in building areas other than corridors or exitways. See for information on proper application and interpretation of experimental results from use of this test.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 The text of this standard references notes and footnotes that provide explanatory information. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of this standard.1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of materials, products, or assemblies under actual fire conditions.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.

Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source

ASTM E1796-03(2011)e1 建筑物含铅漆用液体涂层封装产品的选择和使用标准指南

This standard primarily addresses encapsulant products for residential and child-care facilities. It may also be appropriate for some commercial buildings. Encapsulation provides a means of protecting occupants from exposure to lead in paint in buildings that are likely to remain standing for a long period of time. This nondestructive abatement strategy is useful in situations in which the primary structure needs to remain intact for either historical or economic reasons. Encapsulation offers an abatement strategy that may be more cost effective than abatement by removal of the paint. There are many environmental and use conditions that affect leaded paint liquid coating encapsulation products, and different types of liquid coating encapsulation products have been developed specifically to meet the requirements of the various conditions. Product types include reinforced and non-reinforced liquid coatings, as well as products for interior or exterior use. These products may be applied over many different surfaces coated with one or more layers of leaded paint and possibly other coatings. Encapsulation products in service are subjected to many kinds of wear. Various colors and finishes are also available. This guide is intended to assist the purchaser in determining which product is most appropriate for the specific conditions under which the product will be used. As described in this guide, an encapsulation product must be compatible with the surface to which it is applied. An encapsulation product must bond to the surface coating, and not cause the subsurface layers to separate or adversely deteriorate.1.1 This guide is intended to provide building users such as private building owners, contractors, architects, homeowners, and regulatory authorities with assistance in selecting an appropriate liquid coating encapsulation product for architectural residence and child-care facility use situations for abating leaded paint. This guide also provides information that can be used to assist in the following: (1) determining whether a painted surface is suitable for encapsulation, (2) applying a liquid coating encapsulation product, (3) evaluating installed liquid coating encapsulation products, and (4) maintaining the encapsulated surface. 1.2 This guide applies to any liquid-applied product that relies primarily on adhesion for attachment to the surface and is designed to reduce human exposure to lead in paint. 1.3 This guide is not intended for use as a training manual. The information contained herein is not all-inclusive and does not provide comprehensive instructions for the selection, application, or maintenance of specific liquid coating encapsulation products. This guide is intended to supplement information supplied by encapsulation product manufacturers and safety requirements established by law. The user of this guide shall refer to the encapsulation product manufacturer''s instructions for encapsulation product application and maintenance. 1.4 This guide does not cover minimum material performance requirements for liquid coating encapsulation products. Performance specifications for non-reinforced liquid coating encapsulation products are provided in Specification E1795. Performance specifications for reinforced liquid coating encapsulation products are provided in Specification E1797. 1.5 Encapsulation products for use on industrial steel structures are not covered in this guide. Industrial steel structures include, but are not limited to, bridges, water towers, and tanks. 1.6 Limited docum......

Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings

ASTM F141-03 弹性地板覆盖物相关的标准术语

Standard Terminology Relating to Resilient Floor Coverings

ASTM D4977-03(2009) 用磨擦法对矿物涂覆的屋顶层颗粒粘结的测试方法

This test method is used to determine the quality of adhesion of the granular surfacing to the coating asphalt in a sample of mineral surfaced roofing. The results determine compliance with the applicable specification requirements or for comparative analysis. This test method applies to “as manufactured” material and may not be applicable to material that has had weathering exposure.1.1 This test method covers the determination of granule adhesion to mineral surfaced roofing due to abrasion. 1.2 The values stated in SI units are regarded as standard. The inch-pound units in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

NF P62-307:2002 弹性地板覆盖物.用于特别潮湿地区的聚氯乙烯地板覆盖物

Resilient floor coverings - Polyvinyl chloride floor coverings for use in special wet areas - Specification.

NF P62-102:2002 弹性和叠层地板覆盖物.小脚轮椅试验

Resilient and laminate floor coverings - Castor chair test.

JG/T 26-2002 外墙无机建筑涂料

本标准规定了建筑物外墙表面用无机建筑涂料的技术要求、试验方法、检验规则、包装、标志、运输和贮存等。 本标准适用于以碱金属硅酸盐或硅溶胶为主要粘结剂的外墙无机建筑涂料，采用刷涂、喷涂或滚涂的施工方法，在建筑物外墙表面形成薄质装饰涂层。

Inorganic building coating for external wall

DIN EN 235:2002 墙面饰层.术语符号

This European Standard defines terms of interest to the users of wallcoverings that are supplied in roll form for hanging on to walls and ceilings by means of an adhesive covering the whole of the interface between the wallcovering and the support. This standard also provides the necessary definitions and symbols for the purposes of other European Standard for wallcoverings (see references in clause 2). Table 1 gives the symboles to be used.

Wall coverings - Vocabulary and symbols; German version EN 235:2001

NF P62-101:2002 弹性地板覆盖物.模拟家具腿移动的影响测定

Resilient floor coverings - Determination of the effect of the simulated movement of a furniture leg.

NF D63-001:2002 墙壁纸.词汇和符号

Wallcoverings - Vocabulary and symbols.

DLA OO-S-2927 NOTICE 1-2002 便携式喷漆装备

This notice should be filed in front of OO-S-2927, dated June 30, 1997.

SPRAY OUTFITS, PAINT, PORTABLE

ASTM F925-02 弹性地板材料耐化学药品的标准试验方法

Resilient flooring products are designed and formulated to have good resistance to most common chemicals encountered in typical use. High performance wear layers can also be used to enhance cleanability and chemical resistance. Resilient flooring used in residential and commercial environments may be subjected to a variety of chemicals through accidental spillage or as ingredients used for hygienic purposes. Performance is dependent upon the flooring formulation and that of the maintenance products used on the flooring. This test method provides a means of estimating the relative susceptibility of resilient floor covering to change when exposed to chemical reagents.1.1 This test method provides a procedure for determining the resistance of resilient floor covering to surface deterioration when exposed to various chemical reagents. This test method is not intended as a staining test nor as a method to judge surface and appearance restoration of the sample after exposure to the chemical reagent. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are provided in Section of this test method.

Standard Test Method for Resistance to Chemicals of Resilient Flooring

ASTM F1303-02 带背衬薄板型乙烯地面覆盖物的标准规范

1.1 This specification covers floor covering having a vinyl plastic wear layer with backing. Products may also contain non-PVC specialty performance top layer(s) or intermediate layer(s), or both.1.2 Two types of floor covering based on binder content are covered. The floor covering is intended for use in commercial, light commercial, and residential buildings based on serviceability characteristics. General information and performance characteristics that determine serviceability and recommended use are included in this specification.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 The following safety hazards caveat pertains only to the test methods portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Sheet Vinyl Floor Covering with Backing

ASTM E1740-02 用锥形热量计测定墙面覆层材料的释热率及其它着火试验响应特性的标准试验方法

1.1 This fire-test-response test method covers determination of the ignitability and heat release rate of composites consisting of a wallcovering, a substrate, and all laminating adhesives, coatings, and finishes. Heat release information cannot be used alone to evaluate the flammability of wallcoverings. The data are intended to be used for modeling or with other data to evaluate a material.1.2 This test method provides for measurement of the time to sustained flaming, heat release rate, peak and total heat release, and effective heat of combustion at a constant radiant heat flux of 35 kW/m 2. Heat release data at different heating fluxes are also obtained by this test method. The specimen is oriented horizontally, and a spark ignition source is used.1.3 The fire-test-response characteristics are determined using the apparatus and procedures described in Test Method E 1354.1.4 The tests are conducted on bench-scale specimens combining the components used in the actual installation.1.5 The values stated in SI units are to be regarded as the standard; see Practice E 380.1.6 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be used in conducting these tests. This test method potentially involves hazardous materials, operations, and equipment.1.7 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.1.8 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section .1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter

ASTM D2824-02 无纤维增强、石棉纤维增强和无石棉的纤维增强的填充铝颜料的沥青屋面涂层标准规范

1.1 This specification covers asphalt-based, aluminum roof coatings suitable for application to roofing or masonry surfaces by brush or spray.1.2 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Aluminum-Pigmented Asphalt Roof Coatings, Nonfibered, Asbestos Fibered, and Fibered without Asbestos