Q20 筑路材料 标准查询与下载

ASTM D6690-06a 沥青铺路和混凝土热应用连接和裂纹密封剂的标准规范

1.1 This specification covers joint and crack sealants of the hot applied type intended for use in sealing joints and cracks in Portland Cement Concrete and Asphaltic Concrete Pavements.1.2 The values stated in SI units are the standard.1.3 This standard does not purport to cover the properties required of sealants for use in areas of Portland Cement concrete or asphaltic pavement subject to jet fuel or other fuel spillage such as vehicle and/or aircraft refuel and maintenance areas.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

ASTM D6690-06 沥青铺路和混凝土热应用连接和裂纹密封剂的标准规范

1.1 This specification covers joint and crack sealants of the hot applied type intended for use in sealing joints and cracks in Portland Cement Concrete and Asphaltic Concrete Pavements.1.2 The values stated in SI units are the standard.1.3 This standard does not purport to cover the properties required of sealants for use in areas of Portland Cement concrete or asphaltic pavement subject to jet fuel or other fuel spillage such as vehicle and/or aircraft refuel and maintenance areas.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

ASTM D6244-06(2011) 土工符合材料公路板式排水沟垂直压缩的标准试验方法

The vertical compression test for geocomposite pavement panel drains is intended to simulate vertical, horizontal, and eccentric loading resulting from an applied vertical load. The results of the analyses, including vertical strain of the panels and core area change, may be used as an index test. The vertical compression test may be used to evaluate core area change for a given load. The vertical compression test may be used to evaluate percent vertical strain for a given load. This test method may be modified to evaluate core area change and vertical strain under various backfill conditions.1.1 This test method covers vertical strain and core area change of geocomposite pavement drains, such as those included in Specification D7001, under vertical compression. 1.2 The values as stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Vertical Compression of Geocomposite Pavement Panel Drains

BS EN 12274-8:2005 泥浆表面修整.试验方法.缺陷的目视评估

This European Standard specifies qualitative and quantitative test methods of the visual assessment of defects of slurry surfacing. This European Standard is applicable to all slurry surfacing (roads, airfields and other areas). The visual assessment reports for both methods have identical records and thus both may be used to check the specification for visual assessment of defects. Defects emanating from the substrate (existing road) must not be taken into consideration. NOTE 1 The qualitative and quantitative tests may be used separately or sequentially. This may relate to different types of sites (for example lightly trafficked roads may not be required to be quantitatively assessed). NOTE 2 The test may be used to evaluate the durability of slurry surfacing.

Slurry surfacing - Test methods - Visual assessment of defects

BS EN 14840:2005 填缝料和密封剂.预制接缝密封件的试验方法

This European Standard specifies the test methods for preformed joint seals made of vulcanised rubber for use in concrete pavements.

Joint fillers and sealants - Test methods for preformed joint seals

NF P98-818-43:2005 沥青.沥青混合物.热混沥青的试验方法.第43部分:耐燃料性

Asphalt - Pr?Bituminous mixtures - Test methods for hot mix asphalt - Part 43 : resistance to fuel.

NF P98-818-41:2005 沥青混合物.热混沥青的试验方法.第41部分:耐解冻液

Bituminous mixtures - Test methods for hot mix asphalt - Part 41 : resistance to de-icing fluids.

BS 7533-3:2005+A1:2009 用粘土,天然石或混凝土铺筑材料进行的路面.第3部分:挠性路面用预制混凝土铺筑石块和粘土铺筑材料铺设的规程

This part of BS 7533 gives recommendations for the laying of conventional and permeable pavements using precast concrete paving blocks conforming to BS EN 1338 and clay pavers conforming to BS EN 1344. This standard is intended for flexible pavements for roads, industrial areas and other paved surfaces subjected to all categories of static and vehicular loading and pedestrian traffic. The principles given apply to all shapes and sizes of paving units covered by BS EN 1338 and BS EN 1344.

Pavements constructed with clay, natural stone or concrete pavers — Part 3: Code of practice for laying precast concrete paving blocks and clay pavers for flexible pavements

BS 7533-3:2005 用粘土、天然石或混凝土铺筑材料建造的路面.挠性路面用预制混凝土铺筑石块和粘土铺筑材料铺设的实用规程

This part of BS 7533 gives recommendations for the laying of conventional and permeable pavements using precast concrete paving blocks conforming to BS EN 1338 and clay pavers conforming to BS EN 1344. This standard is intended for flexible pavements for roads, industrial areas and other paved surfaces subjected to all categories of static and vehicular loading and pedestrian traffic. The principles given apply to all shapes and sizes of paving units covered by BS EN 1338 and BS EN 1344.

Pavements constructed with clay, natural stone or concrete pavers - Code of practice for laying precast concrete paving blocks and clay pavers for flexible pavements

DIN EN 13286-48:2005 松散的和液力粘合的混合料.第48部分:粉碎作用程度测定的试验方法

This European Standard specifies a test method for the determination of the degree of pulverization of cohesive material after mixing with lime and/or hydraulic binder.

Unbound and hydraulically bound mixtures - Part 48: Test method for the determination of degree of pulverisation; German version EN 13286-48:2005

BS EN 13084-5:2005 独立式工业用烟囱.砖衬垫材料.产品规范

This European Standard specifies performance requirements and test methods for clay/ceramic bricks and factory made mortars used for the construction of brick liners in free-standing industrial chimneys. The structural design of the brick liners is specified in EN 13084-4. The marking requirement for bricks and mortar covered by this European Standard is included. This European Standard provides for the evaluation of conformity of material for brick liners to this EN.

Free-standing chimneys - Material for brick liners - Product specifications

NF P98-818-25:2005 沥青混合料.热混沥青的试验方法.第25部分:循环压力试验

Bituminous mixtures - Test methods for hot mix asphalt - Part 25 : cyclic compression test.

NF P98-818-4:2005 沥青混合物.热混合沥青的试验方法.第4部分:沥青回收:分馏柱

Bituminous mixtures - Test methods for hot mix asphalt - Part 4 : bitumen recovery : fractionating column.

DIN EN 12274-7:2005 泥浆表面处理.第7部分:振动磨擦试验

This document specifies a test method for determining the suitability of aggregates and cationic emulsions for slurry surfacings and, where appropriate, the effect of individual additives. This document applies to slurry surfacings.

Slurry surfacing - Part 7: Shaking abrasion test; German version EN 12274-7:2005

BS EN 13877-2:2005 混凝土路面.混凝土路面的功能要求

Concrete pavements - Functional requirements for concrete pavements

BS EN 13877-2:2004 混凝土路面.测定混凝土路面对镶钉轮胎的耐磨性的试验方法

This document specifies requirements for concrete pavements cast in-situ and compacted by vibration. It also covers concrete sub-bases as well as wearing courses on bridges. This document covers concrete pavements in motorways, airfields, pedestrian streets, cycle tracks, storage areas and, in general, all traffic-bearing structures.

Concrete pavements-Part 2:Functional requirements for concrete pavements

BS 594-1:2005 道路和其他铺砌区用热压制沥青.组分材料与沥青混合物规范

This part of BS 594 specifies requirements for mixtures of hot rolled asphalt to be laid as surface course, regulating course, binder course or base (roadbase) on roads and other paved areas, excluding heavy duty airfield pavements. It also specifies requirements for coated chippings, but excludes requirements for site-specific properties such as polished stone values and abrasion values of aggregates. NOTE The terms "base (roadbase)","binder course" and "surface course" are used throughout this standard in place of the traditional terms "roadbase","basecourse" and "wearing course" respectively to encourage use of the new terminology which will be used in European asphalt standards to be introduced in the near future.

Hot rolled asphalt for roads and other paved areas - Specification for constituent materials and asphalt mixtures

BS 4987-1:2005 道路及其它铺砌区用沥青盖层碎石路(沥青混凝土).组分材料和混合物规范

This part of BS 4987 specifies the requirements for all types of coated macadam (asphalt concrete) to be laid as base (roadbase) (group one), binder course (group two), surface course (group three) or porous asphalt surface course (group four) for roads and other paved areas excluding heavy duty airfield pavements. This standard does not include requirements for macadams incorporating bitumen emulsions as binders which are specified in BS 434-1. NOTE The terms "base (roadbase)", "binder course" and "surface course" are used throughout this standard in place of the traditional terms "roadbase", "basecourse" and "wearing course" respectively to encourage use of the new terminology which will be used in European asphalt standards to be introduced in the near future.

Coated macadam (asphalt concrete) for roads and other paved areas - Specification for constituent materials and for mixtures

EN 12697-41:2005 沥青混合物.热混沥青用试验方法.第41部分:耐防冻液

This European Standard specifies a test method to determine the resistance of bituminous materials to deicing fluids such as solutions of acetate and formate. The procedure determines the surface tensile strength of a specimen of asphalt after storage in de-icing fluid. This European Standard is primarily used as a test on asphalt to be laid on airfields, but it can be used for asphalt to be laid on roads or other paved areas.

Bituminous mixtures Test methods for hot mix asphalt Part 41: Resistance to de-icing fluids

NF P98-818-39:2005 沥青混合料.热混沥青的试验方法.第39部分:用点燃法测定粘合剂含量

Bituminous mixtures - Test methods for hot mix asphalt - Part 39 : binder content by ignition.