Q25 绝热、吸声、轻质与防火材料 标准查询与下载

ASTM C578-17a 硬质多孔聚苯乙烯隔热材料的标准规格

1.1 This specification2 covers the types, physical properties, and dimensions of cellular polystyrene boards with or without facings or coatings made by molding (EPS) or extrusion (XPS) of expandable polystyrene. Products manufactured to this specification are intended for use as thermal insulation for temperatures from -65 to +165°F (-53.9 to +73.9°C). This specification does not apply to laminated products manufactured with any type of rigid board facer including fiberboard, perlite board, gypsum board, or oriented strand board. 1.1.1 For Type XIII only, this specification covers the physical properties, and dimensions of cellular polystyrene intended for use as thermal insulation for temperatures from −297 to +165°F (−183 to +73.9°C). 1.2 Consult the manufacturer for specific recommendations and properties in cryogenic conditions. 1.2.1 This specification does not cover cryogenic properties except for the k-factors for Type XIII in Appendix X1. For Type XIII in specific cryogenic applications, the manufacturer and purchaser shall agree upon the actual temperature limits and physical property requirements in addition to the k-factors in Appendix X1. 1.3 The use of thermal insulation materials covered by this specification may be regulated by building codes that address fire performance. For some end uses, specifiers should also address the effect of moisture and wind pressure resistance. Guidelines regarding these end use considerations are included in Appendix X1. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation

ASTM C1482-17 聚酰亚胺柔性多孔隔热和吸声材料的标准规格

1.1 This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for temperatures from –328°F up to +572°F (–200°C and +300°C) in commercial and industrial environments. 1.1.1 Annex A1 includes faced polyimide foam as specified by the U.S. Navy for marine applications. 1.1.2 This standard is designed as a material specification and not a design document. Physical property requirements vary by application and temperature. No single test is adequate for estimating either the minimum or maximum use temperature of polyimide foam under all possible conditions. Consult the manufacturer for specific recommendations and physical properties for specific applications. 1.1.3 The use of an appropriate vapor retarder is required in all applications where condensation could occur and cause a decrease in thermal performance or affect other system properties. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: The subject matter of this material specification is not covered by any other ASTM specification. There is no known ISO standard covering the subject of this standard. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation

ASTM C461-17 隔热用胶粘剂和涂层的标准试验方法

1.1 These test methods cover procedures for sampling and testing mastics and coatings for use as weather and vapor barrier finishes on thermal insulations and for other accessory use. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The test methods appear in the following order:   Section Sampling 4 Uniformity and Storage Stability 5 Stability Under Freezing 6 Density and Weight per Gallon 7 Consistency 8 Solids Content 9 Content of Volume Solids and Coverage of Mastics and Coatings 10 Sag Resistance (Build) 11 Drying Time 12

Standard Test Methods for Mastics and Coatings Used With Thermal Insulation

ASTM C653-17 低密度毯型矿物纤维绝缘耐热性测定的标准指南

4.1 This guide provides a method to determine the thermal performance of low-density blanket-type insulation. It may be used for the purposes of quality assurance, certification, or research. 4.2 The thermal resistance of low-density insulation depends significantly on the density, the thickness, and thermal conductivity. Typical low-density, mineral-fiber insulation for buildings may vary in density from one specimen to the next. 4.3 Thermal tests are time-consuming in comparison with density and thickness measurements. Low-density insulation material is produced in large quantities. A typical lot would be a truckload or the amount necessary to insulate a house. 4.4 The relatively low unit cost of this product and the relatively high cost of thermal resistance testing makes it cost-effective to test only a small percentage of the product area. It is recommended that there be a determination of the density that is representative of a lot by the measurement of the average density of a statistically representative sampling. 4.5 A fewer number of thermal measurements are then made to determine the apparent thermal conductivity at the previously determined representative density. The essential significance of this guide is that a large lot of variable material is best characterized by: (a) determining the representative density, and by (b) determining the thermal property at this representative density with a small number of thermal measurements. 4.6 Building insulation products are commonly manufactured in thicknesses ranging from 19 to 330 mm (0.75 to 13 in.) inclusive. Experimental work has verified that there is a dependence of λapp on thickness for some low density materials. 4.7 The upper limit of test thickness for specimens evaluated using Test Methods C177, C518, and C1114 is established based upon the apparatus design, overall dimensions, expected thermal resistivity level and desired target accuracy. The testing organization is responsible for applying these restrictions when evaluating a product to ensure that the results meet applicable product labels and any existing regulatory requirements (2). 4.8 Extrapolation of the apparent thermal conductivity or the thermal resistance beyond the ranges of thickness or density of products tested is not valid. 1.1 This guide describes the calculation and interpolation of a thermal resistance value for low-density blanket-type insulation material at a particular density and thickness having been selected as representative of the product. It requires measured values of this average density and thickness, as well as apparent thermal conductivity value......

Standard Guide for Determination of the Thermal Resistance of Low-Density Blanket-Type Mineral Fiber Insulation

BS EN 15701:2016 塑料.建筑设备和工业装置用隔热产品用热塑性套管要求和试验方法

Plastics. Thermoplastic jackets for insulation products for building equipment and industrial installations. Requirements and test methods

BS EN 16382:2016 建筑用隔热产品. 通过隔热产品测定板锚的抗通阻力

Thermal insulation products for building applications. Determination of the pull-through resistance of plate anchors through thermal insulation products

JIS A 9523 ERRATUM 1:2016 勘误

ERRATUM

DIN EN 13165:2016 建筑物隔热产品.工厂制硬质聚氨酯泡沫(PU)产品.规格.德文版本EN 13165-2012+A2-2016

Thermal insulation products for buildings - Factory made rigid polyurethane foam (PU) products - Specification; German version EN 13165:2012+A2:2016

DIN EN 13166:2016 建筑物隔热产品.酚醛泡沫的工厂制(PF) 产品.规格.德文版本EN 13166-2012+A2-2016

Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification; German version EN 13166:2012+A2:2016

JIS A 9523:2016 松散填充热绝缘材料

Loose fill thermal insulation materials

JIS A 9510:2016 无机的多孔隔热材料

Inorganic porous thermal insulation materials

DB37/T 5067-2016 FS外模板现浇混凝土复合保温系统应用技术规程

本规程适用于采用FS复合保温外模板的现浇混凝土梁、柱、墙体，以及供暖与非供暖空间现浇混凝土楼板等保温工程。

FS external formwork cast-in-place concrete composite thermal insulation system application technical specification

DIN EN 13163:2016 建筑物用隔热产品.工厂制膨胀聚乙烯(EPS)产品.规格.德文版本EN 13163-2012+A1-2015

Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification; German version EN 13163:2012+A1:2015

BS ISO 16957:2016 采用周期法测量湿多孔建筑材料的表观导热系数

Measurement of apparent thermal conductivity of wet porous building materials by a periodic method

DB37/T 5064-2016 STP真空绝热板建筑保温系统应用技术规程

本规程适用于新建、扩建、改建的民用建筑和既有建筑节能改造保温工程的设计、施工与验收。

STP Vacuum Insulation Panel Building Thermal Insulation System Application Technical Regulations

JC/T 2367-2016 绝热用硅酸镁纤维毯

Magnesium silicate fiber blanket for thermal insulation

JC/T 2366-2016 建材工业用干法磨边倒角机

Dry edge grinding and chamfering machine for building materials industry

DB31/T 983-2016 改性发泡聚苯乙烯保温板技术要求

本标准规定了热固改性聚苯板的术语和定义、技术要求、试验方法和检验规则。 本标准主要适用于工业与民用建筑中保温隔热用热固改性聚苯板，其他领域用热固改性聚苯板可参照执行。

Technology requirements for modified expanded polystyrene insulation board

BS EN 16724:2016 建筑用隔热产品. 用于测定外保温复合系统 (ETICS) 的着火反应试验的安装和固定说明书

Thermal insulation products for building applications. Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal Insulation composite systems (ETICS)

DIN EN 16724:2016 建筑用隔热产品. 用于测定外保温复合系统 (ETICS) 的着火反应试验的安装和固定说明书; 德文版本EN 16724-2015

Thermal insulation products for building applications - Instructions for mounting and fixing for determination of the reaction to fire testing of external thermal insulation composite systems (ETICS); German version EN 16724:2015