Q27 粘结材料 标准查询与下载

JIS A 6902 AMD 2:2008 抹灰用熟石灰(修改件2)

Plastering lime (Amendment 2)

KS F 3211-2008 屋顶涂覆防水膜

이 규격은 주로 철근 콘크리트조 건축물 및 그 밖의 구조물에 대한 지붕 및 바닥 방수와 외

Waterproofing membrane coating for construction

ANSI A118.10-2008 薄瓷砖和规格石料铺设用承重粘结防水膜

This specification describes the test methods and minimum requirements for load bearing, bonded, waterproof membranes, including fungus resistance, seam strength, breaking strength, waterproofness, etc. Several of the tests are long-term as in several other specifications; for example, the 110-day water immersion shear strength test.

Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations

ANSI A136.1-2008 瓷砖铺设用有机粘结剂的规范

This specification deals with organic adhesives for the installation of ceramic tile in interior areas requiring Type I and Type II water resistance. These products are not intended for continuous water immersion or chemical resistance for example. The applications are classified in the standard. The tests include shear strength, heat resistance, staining (of the adhesive into the tile), mold growth, etc.

Specifications for Organic Adhesives for Installation of Ceramic Tile

ANSI A118.12-2008 薄集瓷砖和规格石料裂纹绝缘薄膜的安装规范

This specification describes the testing and physical properties required for a membrane to be classified as meeting A118.12. These membranes are designed to isolate the tile and stone from minor in-plane cracking in the substrate. This specification measures the membranes' ability to perform in this manner. The crack isolation test jig is also described.

Specifications for Crack Isolation Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations

NF P61-604:2008 瓷砖胶粘剂.湿润性的测定

Adhesives for tiles - Determination of wetting capability.

NF P61-606:2008 瓷砖用粘合剂.水泥粘合剂用抗张粘合强度的测定

Adhesives for tiles - Determination of tensile adhesion strength for cementitious adhesives.

NF P61-605:2008 瓷砖用粘结剂.滑移度的测定

Adhesives for tiles - Determination of slip.

NF P61-603:2008 瓷砖用粘结剂.敞露时间的测定

Adhesives for tiles - Determination of open time.

NF T76-205:2008 建筑装配用一般性粘合剂.要求和试验方法

General purpose adhesives for structural assembly - Requirements and test methods.

ASTM D4070-08 混凝土结构用预制弹性桥梁压缩填缝料安装用粘结剂的标准规范

1.1 This specification covers an adhesive lubricant for facilitating the insertion and positioning of preformed elastomeric bridge compression seals in either concrete or steel-faced joints, and which bonds the seal to the joint faces to waterproof the joint.

Standard Specification for Adhesive Lubricant for Installation of Preformed Elastomeric Bridge Compression Seals in Concrete Structures

ANSI A118.10a-2008 薄瓷砖和规格石料铺设用承重粘结防水膜

This specification describes the test methods and minimum requirements for load bearing, bonded, waterproof membranes, including fungus resistance, seam strength, breaking strength, waterproofness, etc. Several of the tests are long-term as in several other specifications; for example, the 100-day water immersion shear strength test.

Load Bearing, Bonded, Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations

ASTM D3019-08 用于无纤维增强、石棉纤维增强和无石棉的纤维增强沥青屋顶卷材的搭接胶粘剂标准规范

1.1 This specification covers lap cement consisting of asphalt dissolved in a volatile petroleum solvent with or without mineral or other stabilizers, or both, for use with roll roofing. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 The following precautionary caveat applies only to the test method portion, Section 5, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non-Fibered, Asbestos-Fibered, and Non-Asbestos-Fibered

ANSI A118.12a-2008 薄瓷砖和规格石料铺设用裂缝隔离膜规范

This specification describes the testing and physical properties required for a membrane to be classified as meeting A118.12. These membranes are designed to isolate the tile and stone from minor in-plane cracking in the substrate. This specification measures the membranes' ability to perform in this manner. The crack isolation test jig is also described.

Specifications for Crack Isolation Membranes for Thin-Set Ceramic Tile and Dimension Stone Installations

ASTM D6392-08 热溶法测定非增强土工薄膜接缝完整性搭标准试验方法

The use of geomembranes as barrier materials to restrict liquid migration from one location to another in soil and rock has created a need for a standard test method to evaluate the quality of geomembrane seams produced by thermo-fusion methods. In the case of geomembranes, it has become evident that geomembrane seams can exhibit separation in the field under certain conditions. Although this is an index type test method used for quality assurance and quality control purposes, it is also intended to provide the quality assurance engineer with sufficient seam peel and shear data to evaluate seam quality. Recording and reporting data, such as separation that occurs during the peel test and elongation during the shear test, will allow the quality assurance engineer to take measures necessary to ensure the repair of inferior seams during facility construction, and therefore, minimize the potential for seam separation in service.1.1 This test method describes destructive quality control and quality assurance tests used to determine the integrity of geomembrane seams produced by thermo-fusion methods. This test method presents the procedures used for determining the quality of nonbituminous bonded seams subjected to both peel and shear tests. These test procedures are intended for nonreinforced geomembranes only. 1.2 The types of thermal field seaming techniques used to construct geomembrane seams include the following. 1.2.1 Hot Air8212;This technique introduces high-temperature air or gas between two geomembrane surfaces to facilitate melting. Pressure is applied to the top or bottom geomembrane, forcing together the two surfaces to form a continuous bond. 1.2.2 Hot Wedge (or Knife)8212;This technique melts the two geomembrane surfaces to be seamed by running a hot metal wedge between them. Pressure is applied to the top or bottom geomembrane, or both, to form a continuous bond. Some seams of this kind are made with dual bond tracks separated by a nonbonded gap. These seams are sometimes referred to as dual hot wedge seams or double-track seams. 1.2.3 Extrusion8212;This technique encompasses extruding molten resin between two geomembranes or at the edge of two overlapped geomembranes to effect a continuous bond. 1.3 The types of materials covered by this test method include the following. 1.3.1 Very Low Density Polyethylene (VLDPE). 1.3.2 Linear Low Density Polyethylene (LLDPE). 1.3.3 Very Flexible Polyethylene (VFPE). 1.3.4 Linear Medium Density Polyethylene (LMDPE). 1.3.5 High Density Polyethylene (HDPE). 1.3.6 Polyvinyl Chloride (PVC). 1.3.7 Flexible Polypropylene (fPP). Note 18212;The polyethylene identifiers presented in 1.3.1-1.3.5 describe the types of materials typically tested using this test method. These are industry accepted trade descriptions and are not technical material classifications based upon material density. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility......

Standard Test Method for Determining the Integrity of Nonreinforced Geomembrane Seams Produced Using Thermo-Fusion Methods

ASTM D6648-08 使用弯曲束流变仪测定沥青粘结剂柔性蠕变硬度的试验方法

The temperatures for this test are based upon the winter temperature experienced by the pavement in the geographical area for which the asphalt binder is intended. The flexural creep stiffness or flexural creep compliance, determined from this test, describes the low-temperature stress-strain-time response of asphalt binder at the test temperature within the range of linear viscoelastic response. The low-temperature thermal cracking performance of asphalt pavements is related to the creep stiffness and the m-value of the asphalt binder contained in the mix. The creep stiffness and the m-value are used as performance-based specification criteria for asphalt binders in accordance with Specification D 6373. 1.1 This test method covers the determination of the flexural-creep stiffness or compliance and m-value of asphalt binders by means of a bending beam rheometer. It is applicable to material having flexural-creep stiffness values in the range of 20 MPa to 1 GPa (creep compliance values in the range of 50 nPa–1 to 1 nPa–1) and can be used with unaged material or with materials aged using aging procedures such as Test Method D 2872 or Practice D 6521. The test apparatus may be operated within the temperature range from –36°C to 0°C. 1.2 Test results are not valid for test specimens that deflect more than 4 mm or less than 0.08 mm when tested in accordance with this test method. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR)

BS EN 1348:2007 瓷砖用粘合剂.水泥粘合剂的抗张粘合强度的测定

This European Standard specifies a method for the determination of the tensile adhesion strength of cementitious ceramic tile adhesives. This European Standard is applicable to all cementitious adhesives and cementitious adhesives with separate components for internal and external ceramic tile installations on walls and floors. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can be used also for other kinds of tiles (natural and agglomerated stones etc.), if they do not adversely affect the stones.

Adhesives for tiles - Determination of tensile adhesion strength for cementitious adhesives

BS EN 1346:2007 瓷砖用粘合剂.敞露时间的测定

This European Standard specifies the test method for the determination of the open time of ceramic tile adhesives. This European Standard is applicable to all ceramic tile adhesives for internal or external tile installations on walls and floors. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can also be used for other types of tiles (natural and agglomerated stones etc.), if they do not adversely affect the stones.

Adhesives for tiles - Determination of open time

BS EN 1308:2007 瓷砖用粘合剂.滑倒的测定

This European Standard specifies the method for the determination of the resistance to slip of a tile applied to an adhesive on a vertical surface. This European Standard applies to all ceramic tile adhesives for internal and external tiling on walls. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can be used also for other kinds of tiles (natural and agglomerated stones etc.), if they do not adversely affect the stones.

Adhesives for tiles - Determination of slip

BS EN 1347:2007 瓷砖用粘合剂.湿润能力的测定

'This European Standard specifies the method for the determination of the wetting capability of ceramic tile adhesives. This European Standard is applicable to all ceramic tile adhesives for internal or external tile installations on walls and floors. This European Standard does not contain performance requirements or recommendations for the design and installation of ceramic tiles. NOTE Ceramic tile adhesives can also be used for other types of tiles (natural and agglomerated stones etc.), if they do not adversely affect the stones.

Adhesives for tiles - Determination of wetting capability