Q40 耐火材料综合 标准查询与下载

YB/T 4638-2018 顶燃式热风炉用耐火材料技术规范

Technical specifications for refractory materials for top-fired hot blast stoves

YB/T 060-2018 炼钢转炉用耐火砖形状尺寸

Shape and dimensions of refractory bricks for steelmaking converters

JC/T 2408-2017 水泥预热器陶瓷内筒通用技术要求

General technical requirements for cement preheater ceramic inner cylinder

ASTM C865-17 烧制耐火混凝土样品的标准实施规程

3.1 This practice is used to standardize the firing conditions of refractory concrete specimens prepared in accordance with Practice C862. The standards are set down to minimize laboratory-to-laboratory variation and do not attempt to duplicate any particular field applications. 1.1 This practice covers the firing of specimens made from refractory concretes (castable refractories) in accordance with Practice C862 for cast specimens. The procedure is also recommended for heating rates to be used for high-temperature test methods such as Test Methods C16, C583, etc., when these methods are used to test refractory concretes. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Firing Refractory Concrete Specimens

BS ISO 18886:2016 耐火试件制备. 采用湿法喷补技术的喷射耐火板

Refractory test-piece preparation. Gunning refractory panels by wet gunning techniques

YB/T 370-2016 耐火材料 荷重软化温度试验方法(非示差-升温法)

本标准规定了耐火材料荷重软化温度(非示差-升温法)试验方法的术语和定义、原理、设备、试样、试验步骤、试验结果及处理、试验误差、设备检查和试验报告。 本标准适用于耐火材料荷重软化温度(非示差-升温法)的测定。

Refractoies.Determination of refractoriness under load (non-differential, with rising temperature)

ISO 18886:2016 耐火试件制备. 采用湿法喷补技术的喷射耐火板

Refractory test-piece preparation - Gunning refractory panels by wet gunning techniques

ASTM C1171-16 耐火材料热循环效应定量测量的标准试验方法

3.1 This test method indicates the ability of a refractory product to withstand the stress generated by sudden changes in temperature. 3.2 Because the recommended furnace temperature of this cycling test is 1200°C (2190°F), this test method may not indicate the ability of a refractory product to withstand cycling at higher or lower temperatures, especially if the existing morphology of the refractory product changes. 3.3 This test method is useful for research and development, as well as for comparing refractory products. The precision should be considered when using this test for specification purposes. 3.4 Ruggedness tests found the following variables to be rugged: temperature +5°C hot spacing 1/2 to 3/4 in. (12.77 to 19 mm) cold spacing 1/2 to 3/4 in. (12.77 to 19 mm) center vs. end gripping of the bars hot hold time 10 to 15 min cold hold time 10 to 15 min operator air speed 0 to 2 mi/h (0 to 3.2 km/h) initially cold or heated samples last in, first out (LIFO); or first in, first out (FIFO) 8199;removal from the furnace sawed or original surface as tensile face during MOR testing bar thickness 0.......

Standard Test Method for Quantitatively Measuring the Effect of Thermal Shock and Thermal Cycling on Refractories

GOST 20901-2016 鼓风炉的火炉和热风总管布置用耐火和高耐火产品. 规格

Refractory and high-refractory products for laying of stoves and hot blast mains of blast furnaces. Specifications

KS L 3121-2015 绝热耐火砖导热系数测定方法

Testing method for thermal conductivity of insulating refractory bricks

KS L 3117-2015 耐火砖残留线膨胀和收缩系数试验方法

Testing method for residual linear expansion and contraction of refractory bricks

KS L 3119-2015 耐火砖负载软化点试验方法

Testing method for refractoriness-under-load of refractory bricks

KS L 3126-2015 耐火泥浆粒度试验方法

Testing method for grain size of refractory mortar

KS L 3115-1-2015 耐火砖耐压缩强度试验方法

Testing method for cold compressive strength of refractory bricks — Part 1: Test without packing

KS F 1611-1-2015 建筑构造构建的耐火性能标准.第1部分:木造墙壁、地板与天棚

Fire resistance performance for elements of building construction — Part 1: Wall, floor and roof assemblies of light-frame wood structures

KS F 1611-4-2015 建筑构造构建的耐火性能标准.第4部分:复合地板构造

Fire resistance performance for elements of building construction — Part 4: Composite metal deck slab system

GOST 5040-2015 隔热耐火制品. 规格

Heat-insulating refractory products. Specifications

DIN EN 13381-1:2014 测定结构构件耐火作用的试验方法.第1部分:水平防护层;德文版本EN 13381-1-2014

Test methods for determining the contribution to the fire resistance of structural members - Part 1: Horizontal protective membranes; German version EN 13381-1:2014

JC/T 2241-2014 预制混凝土检查井

本标准规定了预制混凝土检查井的术语和定义、分类、规格尺寸和标记、原材料和构造要求、技术要求、试验方法、检验规则、标志、运输和保管、使用规定以及出厂证明书。本标准适用于地下管道工程用圆形和矩形预制混凝土检查井,包括采用耐腐蚀混凝土材料制作的预制混凝土检查井。采用PVC防腐内衬或玻璃钢防腐内衬制作的防腐型预制混凝土检查井可参照本标准执行。

Prefabricated concrete manhole

JC/T 2272-2014 水泥窑用白云石砖

本标准规定了水泥窑用白云石砖的分类、技术要求、试验方法、检验规则以及包装、标志、运输、贮存和质量证明书。本标准适用于由煅烧过的白云石或煅烧白云石和氧化镁为主要原料制成的水泥窑用白云石砖。

Dolomite bricks for cement kilns