Q70 建筑构配件与设备综合 标准查询与下载
共找到 783 条与 建筑构配件与设备综合 相关的标准，共 53 页
This standard defines minimum design and performance specifications for non-fire rated rolling sheet doors.
Standard for Rolling Sheet Doors
- ICS
- 91.060.50
- CCS
- Q70
- 发布
- 2012
- 实施
Provides a two-part methodology of designing for wind uplift resistance of non-ballasted Built-Up, Modified Bitumen, and Single-Ply roofing system assemblies installed over any type of roof deck.
Wind Design Standard Practice for Roofing Assemblies
- ICS
- 91.060.20
- CCS
- Q70
- 发布
- 2012
- 实施
This specification recognizes that the effectiveness of a sheet radiant barrier is dependent on proper installation. Practices C1743 and C1744 address use and installation of radiant barriers. This specification identifies the material properties that are important for sheet radiant barrier products. When appropriate, values for the properties have been stated. When specific material properties are required for a particular application the user shall consult the manufacturer. Radiant barriers shall be free of dust or other contaminants to remain effective. 1.1 This specification covers the general physical property requirements of radiant barrier materials for use in building construction. The scope is specifically limited to requirements for radiant barrier sheet materials that consist of at least one surface having a far-infrared emittance of 0.1 or less, such as metallic foils or metallic deposits mounted or unmounted on substrates. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 The following safety hazards caveat pertains only to the test methods (Section 10) described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Sheet Radiant Barriers for Building Construction Applications
- ICS
- 91.120.10 (Thermal insulation of buildings)
- CCS
- Q70
- 发布
- 2012
- 实施
4.1 This test method details the calibration and testing procedures and necessary additional temperature instrumentation required in applying Test Method C1363 to measure the thermal transmittance of fenestration systems mounted vertically in the thermal chamber. 4.2 The thermal transmittance of a test specimen is affected by its size and three-dimensional geometry. Care must be exercised when extrapolating to product sizes smaller or larger than the test specimen. Therefore, it is recommended that fenestration systems be tested at the recommended sizes specified in Practice E1423 or NFRC 100. 4.3 Since both temperature and surface heat transfer coefficient conditions affect results, use of recommended conditions will assist in reducing confusion caused by comparing results of tests performed under dissimilar conditions. Standardized test conditions for determining the thermal transmittance of fenestration systems are specified in Practice E1423 and Section 6.2. The performance of a test specimen measured at standardized test conditions is potentially different than the performance of the same fenestration product when installed in the wall of a building located outdoors. Standardized test conditions often represent extreme summer or winter design conditions, which are potentially different than the average conditions typically experienced by a fenestration product installed in an exterior wall. For the purpose of comparison, it is essential to calibrate with surface heat transfer coefficients on the Calibration Transfer Standard (CTS) which are as close as possible to the conventionally accepted values for building design; however, this procedure can be used at other conditions for research purposes or product development. 4.4 Similarly, it would be desirable to have a surround panel that closely duplicates the actual wall where the fenestration system would be installed. Since there are such a wide variety of fenestration system openings in North American residential, commercial and industrial buildings, it is not feasible to select a typical surround panel construction for installing the fenestration system test specimen. Furthermore, for high resistance fenestration systems installed in fenestration opening designs and constructions that have thermal bridges, the large relative amount of heat transfer through the thermal bridge will cause the relatively small amount of heat transfer through the fenestration system to have a larger than desirable error. For this reason, the Calibration Transfer Standard and test specimen are installed in a homogeneous surround panel constructed from materials having a relatively high thermal resistance. Installing the test specimen in a relatively high thermal resistance surround panel places the focus of the test on the fenestration system thermal performance alone. Therefore, it is important to recognize that the thermal transmittance results obtained from this test method are for ideal laboratory conditions, and should only be used for fenestration product comparisons unless the thermal bridge effects that have the potential to occur due to the specific design and construction of the fenestration system opening are ............
Standard Test Method for Measuring the Steady-State Thermal Transmittance of Fenestration Systems Using Hot Box Methods
- ICS
- 91.060.50 (Doors and windows); 91.120.10 (Thermal
- CCS
- Q70
- 发布
- 2012
- 实施
This standard describes vertically-mounted fabricated aluminum slide gates with full aperture closure, designed for either seating or unseating head, or both, in ordinary water supply and wastewater service.. The gates are primarily used to shut off or throttle water or wastewater flow through a rectangular or round orifice, end of channel, or in-channel opening. They may be either conventional-closure or of flush bottom-closure type and may be opened upward or downward.
Fabricated Aluminum Slide Gates
- ICS
- 23.060.30
- CCS
- Q70
- 发布
- 2012
- 实施
This test method describes the determination of the structural performance of garage door and rolling door assemblies under uniform static air pressure difference, using a test chamber.
Standard Method for Testing Sectional Garage Doors and Rolling Doors: Determination of Structural Performance Under Uniform Static Air Pressure
- ICS
- 91.060.50
- CCS
- Q70
- 发布
- 2012
- 实施
本标准规定了建筑用纱门窗术语和定义、分类和规格、材料、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于民用建筑用纱门窗，工业建筑用纱门窗可参照采用。
Screen doors and screen windows for buildings
- ICS
- 91.060.50
- CCS
- Q70
- 发布
- 2011-12-06
- 实施
- 2012-05-01
이 표준은 바닥충격음 저감을 위해서 사용되는 완충재의 잔류변형 측정방법에 대해서 규정한다.
Measuring method of compressibility of resilient materials for floor impact sound
- ICS
- 91.120.20
- CCS
- Q70
- 发布
- 2011-11-09
- 实施
- 2011-11-09
이 표준은 벽, 바닥, 문, 창, 외벽 부재, 외벽 등의 건물 부재의 공기 전달음 차단 성
Laboratory measurements of airborne sound insulation of building elements
- ICS
- 91.120.20
- CCS
- Q70
- 发布
- 2011-11-09
- 实施
- 2011-11-09
이 표준은 건물의 두 실 사이의 벽, 바닥, 문 등의 공기 전달음 차단 성능을 확산 음장의
Field measurements of airborne sound insulation of buildings
- ICS
- 17.160;91.120.20
- CCS
- Q70
- 发布
- 2011-11-09
- 实施
- 2011-11-09
이 표준은 건물의 창호 및 틀의 구성재로 사용하는 합성수지재의 압출 성형 형재(이하 형재라
Plastic profile for windows and doors
- ICS
- 91.060.50
- CCS
- Q70
- 发布
- 2011-10-07
- 实施
- 2011-10-07
이 표준은 건설공사 현장에서 고소 작업 중 작업자가 추락할 위험 및 위험 발생의 우려가 있
Horizontal safety net
- ICS
- 91.12
- CCS
- Q70
- 发布
- 2011-10-07
- 实施
- 2011-10-07
이 표준은 건설 공사 현장에서 가설 구조물의 바깥면에 설치하여 낙하물 및 먼지의 비산 등을
Vertical protective net
- ICS
- 91.12
- CCS
- Q70
- 发布
- 2011-10-07
- 实施
- 2011-10-07
This European standard specifies a test method for the determination of resistance to static loading in order to assess the burglar resistant properties of windows, doors and shutters. It is applicable to the following means of opening: Turning, tilting, folding, turn-tilting, top or bottom hung, sliding (horizontally and vertically) and rolling as well as fixed constructions.
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance under static loading; German version EN 1628:2011
- ICS
- 13.310;91.060.50
- CCS
- Q70
- 发布
- 2011-09
- 实施
This European standard specifies a test method for the determination of resistance to dynamic loading in order to assess the burglar resistant properties of doors, windows and shutters. It is applicable to the following means of opening: Turning, tilting, folding, turn-tilting, top or bottom hung, sliding (horizontally and vertically) and rolling as well as fixed constructions.
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance under dynamic loading; German version EN 1629:2011
- ICS
- 13.310;91.060.50
- CCS
- Q70
- 发布
- 2011-09
- 实施
This European Standard specifies safety requirements and classification systems for burglar resistant characteristics of pedestrian doorsets, windows, curtain walling, grilles and shutters.
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Requirements and classification; German version EN 1627:2011
- ICS
- 13.310;91.060.50
- CCS
- Q70
- 发布
- 2011-09
- 实施
This European standard specifies a test method for the determination of resistance to manual burglary attempts in order to assess the burglar resistant properties of windows, doors and shutters. It is applicable to the following means of opening: Turning, tilting, folding, turn-tilting, top or bottom hung, sliding (horizontally and vertically) and rolling as well as fixed constructions.
Pedestrian doorsets, windows, curtain walling, grilles and shutters - Burglar resistance - Test method for the determination of resistance to manual burglary attempts; German version EN 1630:2011
- ICS
- 13.310;91.060.50
- CCS
- Q70
- 发布
- 2011-09
- 实施
This document covers the following types of steel rolling shutter assemblies: un-insulated manually operated shutters, un-insulated powered shutters, insulated manually operated shutters and insulated powered shutters. This document prescribes the methodology for extending the application of test results obtained from test(s) conducted in accordance with EN 1634-1.
Extended application of test results for fire resistance and/or smoke control for door, shutter and openable window assemblies including their elements of building hardware - Part 10: Fire resistance of steel rolling shutter assemblies; German version EN
- ICS
- 13.220.50;91.060.50
- CCS
- Q70
- 发布
- 2011-07
- 实施
