建筑构配件与设备综合标准-分析测试百科网

EN 16034:2014 行人门,工业,商业;车库门及可开式窗户.产品标准,性能特性.防火性及/或烟雾控制特性

This European Standard identifies material independent, safety and performance requirements applicable to all fire resisting and/or smoke control products intended to be used in fire and/or smoke compartmentation and/or escape routes, which are either:- industrial, commercial and/or garage doorsets, rolling shutters or operable fabric curtains intended for the installation in areas in the reach of persons and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons, or; - rolling shutters or operable fabric curtains used in retail premises which are mainly provided for the access of persons rather than vehicles or goods, or; - pedestrian doorsets and/or openable windows and/or inspection hatches which are hinged or sliding, intended for the installation in areas in the reach of persons, and for which the main intended uses are giving safe access for persons and which are manually or power operated and; - opening and self closing as a normal mode of operation, or; - normally held open but self closing in case of fire or smoke, or; - normally maintained locked in the closed position (e. g. service access/inspection doorsets), and completed; - with building hardware; - with or without any side panel(s), flush over panel(s) and/or transom panel(s) (with or without glazing) and contained within a single perimeter frame for inclusion in a single aperture; - with or without any vision panel(s) in the door leaf or leave(s); - with or without any seals (e. g. for smoke control, fire resistance, draught, acoustic or weather characteristics). Product characteristics covered in EN 13241-1, EN 14351-1, prEN 14351-2 or EN 16361 will not compromise the fire resistance and/or smoke control characteristics of a fire resisting and/or smoke control product. NOTE 1 Requirements included in EN 14351-1, prEN 14351-2, EN 13241-1 or EN 16361 might be relevant for the products covered by this standard. This standard also provides indica

Pedestrian doorsets@ industrial@ commercial@ garage doors and openable windows - Product standard@ performance characteristics - Fire resisting and/or smoke control characteristics

ICS: 13.220.50;91.060.50
CCS: Q70
发布: 2014-10
实施

JG/T 448-2014 既有采暖居住建筑节能改造能效测评方法

本标准规定了既有采暖居住建筑节能改造能效测评的基本要求、采暖效果测评方法、采暖能耗测评方法、供热节能技术应用测评方法。本标准适用于具备热计量功能的既有居住建筑集中采暖系统的节能运行能效测评,以及节能改造效果测评。新建建筑能效测评可参照执行。

Method of the energy performance evaluation for heating system in existing residential buildings

ICS: 91.060.01
CCS: Q70
发布: 2014-09-29
实施: 2015-04-01

JG/T 443-2014 建筑遮阳硬卷帘

本标准规定了建筑遮阳硬卷帘(以下简称“硬卷帘”)的术语和定义、分类代号及标记、一般要求、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于工业和民用建筑用外遮阳硬卷帘产品。

Roller shutter for building

ICS: 91.060
CCS: Q70
发布: 2014-09-11
实施: 2015-02-01

DIN EN 13120:2014 内用百页窗.包括安全性的性能要求.德文版本EN 13120-2009+A1-2014

Internal blinds - Performance requirements including safety; German version EN 13120:2009+A1:2014

ICS: 91.060.50
CCS: Q70
发布: 2014-09-01
实施

DIN EN 15269-5:2014 门, 百叶窗和可开窗组合, 包括建筑五金元件的耐火性和/或烟雾控制试验结果的扩展应用. 第5部分: 铰接和枢接金属框玻璃门组和可打开窗户的耐火性; 德文版本EN 15269-5-2014

Extended application of test results for fire resistance and/or smoke control for door, shutter and openable window assemblies, including their elements of building hardware - Part 5: Fire resistance of hinged and pivoted metal framed glazed doorsets and

ICS: 13.220.50;91.060.50
CCS: Q70
发布: 2014-09
实施

EN 13381-2:2014 确定结构构件耐火性贡献的试验方法第2部分：垂直保护膜

This European Standard specifies a test method for determining the ability of a vertical protective membrane, when used as a fire resistant barrier, to contribute to the fire resistance (loadbearing capacity R) of loadbearing vertical structural building members fabricated from steel, concrete, steel/concrete composites or timber. The method described is applicable to any type of vertical protective membrane, which can be associated with a separate bracing membrane. The vertical protective membrane can be either separated from or attached to the structural building member and is self-supporting. This test method is applicable to vertical protective membranes where there is a gap and a cavity between the vertical protective membrane and the structural building member, otherwise alternative test methods prEN 13381-3, EN 13381-4, EN 13381-6 or prEN 13381-7 should be used as appropriate. This test method and assessment is not applicable to the following: a) all situations where the cavity is to be used as a service or ventilation shaft; b) all situations where the vertical protective membrane acts as a bracing membrane. This European Standard contains the fire test which specifies the tests which shall be carried out whereby the vertical protective membrane together with the structural member to be protected is exposed to the specified fire. The fire exposure, to the standard temperature/time curve given in EN 1363-1, is applied to the side which would be exposed in practice. The test method makes provision, through specified optional additional procedures, for the collection of data which can be used as direct input to the calculation of fire resistance according to the processes given in EN 1992-1-2, EN 1993-1-2, EN 1994-1-2 and EN 1995-1-2. This European Standard also contains the assessment which provides information relative to the analysis of the test data and gives guidance for the interpretation of the results of the fire test, in terms of loadbearing capacity c

Test methods for determining the contribution to the fire resistance of structural members - Part 2: Vertical protective membranes

ICS: 13.220.50;13.220.99
CCS: Q70
发布: 2014-09
实施

EN 1487:2014 建筑物阀门.液压安全组.试验和要求

This European Standard specifies dimensions, materials and performance requirements (including methods of test) for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures1) from 0,1 MPa (1 bar) to 0,7 MPa (7 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95°C. Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater. Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure. NOTE The use of the device specified in this European Standard does not override the need to use controls (e. g. thermostats and cut-outs) which act directly on the power sources of water heaters.

Building valves - Hydraulic safety groups - Tests and requirements

ICS: 91.140.60
CCS: Q70
发布: 2014-07
实施

BS EN 15269-5:2014 门, 百叶窗和可开窗组合, 包括建筑五金元件的耐火性和/或烟雾控制试验结果的扩展应用. 铰接和枢接金属框玻璃门组和可打开窗户的耐火性

Extended application of test results for fire resistance and/or smoke control for door, shutter and openable window assemblies, including their elements of building hardware. Fire resistance of hinged and pivoted metal framed glazed doorsets and openable

ICS: 13.220.50;91.060.50
CCS: Q70
发布: 2014-06-30
实施: 2014-06-30