Q73 金属构配件 标准查询与下载

AS 2728:2007 内部/外部建筑用预修整/预喷涂金属板制品.性能要求

This Standard specifies performance requirements for prepainted and organic film/metal laminate products in sheet and strip form that are coated on one or both sides, and that are intended for fabrication into products for use in the construction or finishing of buildings. The Standard classifies prefinished/prepainted metal products into six types according to their performance, in respect to durability and aesthetics, in environments of varying severity. NOTES: 1 Advice and recommendations on information to be supplied by the purchaser at the time of enquiry or order are contained in the purchasing guidelines set out in Appendix A. 2 To demonstrate a means of compliance to this Standard refer to Appendix B. 3 The performance of a coating will be dependent on the corrosion resistance of the substrate in the particular environment and on climatic influences that directly affect the coating. Such influences include solar radiation and the presence of water vapour (see Appendix C). 4 A guide for the safe application for paint products on metallic substrates is shown in Appendix M. 5 Appendix N sets out an interim procedure for the testing durability and corrosion resistance in naturally unwashed areas.

Prefinished/prepainted sheet metal products for interior/exterior building applications—Performance requirements

BS DD 1722-18:2007 栏栅.场地周边临时设置钢网栅栏规范

This Draft for Development specifies requirements for the manufacture of steel mesh site perimeter temporary fencing. It includes requirements for the dimensions and construction of fence components. Annex A describes a test method to be used by manufacturers or vendors to determine the wind resistance of the fence. Annex B gives recommendations for the installation of a steel mesh site perimeter temporary fencing system to be provided to vendors and users of the fencing system. Annex C gives recommendations for the renovation of damaged areas of pre-galvanized coating on fence panels. NOTE This Draft for Development complements and expands on the guidance given by the Health & Safety Executive in its guidance document HS G 151, Protecting the public, your next move [1]. This document is intended to assist the construction industry and assist in ensuring the safety of members of the public in the UK.

Fences - Specification for steel mesh site perimeter temporary fencing systems

JG/T 201-2007 建筑幕墙用钢索压管接头

本标准规定了建筑幕墙用钢索压管接头（以下简称接头）的术语和定义、分类与标记、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于公称直径为6mm～36mm，钢丝抗拉强度不大于1700MPa的各类钢绞线、圆股钢丝绳的钢压管接头。 本标准不适用于半密封和密封型钢丝绳压管接头。

Swaged fitting of steel strand for curtain wall

JG/T 196-2007 冷弯钢板桩

本标准规定了冷弯钢板桩的术语和定义、订货内容、制造工艺与交货状态、分类和标记、技术要求、形状、外形尺寸及截面特性、锁口尺寸、外形允许尺寸偏差、交货质量和交货长度、试验方法、检验规则、包装、标志和质量证明书等。 本标准适用于建筑地下工程支护结构、港口建设、水利工程用冷弯钢板桩等。

Cold formed steel sheet piling

ASTM C645-07 非结构钢框架构件的标准规范

1.1 This specification covers nonstructural steel framing members in interior construction assemblies.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are provided for information purposes only.The following safety hazards caveat pertains only to the test methods portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nonstructural Steel Framing Members

ASTM C645-07a 非结构钢框架构件的标准规范

1.1 This specification covers nonstructural steel framing members in interior construction assemblies.1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are provided for information purposes only.The following safety hazards caveat pertains only to the test methods portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nonstructural Steel Framing Members

ASTM F654-07 住宅金属防护网大门的标准规范

1.1 This specification covers detail requirements for residential chain link fence gates, gate posts, and accessories.

Standard Specification for Residential Chain Link Fence Gates

ASTM C645-07b 非结构钢框架构件的标准规范

1.1 This specification covers nonstructural steel framing members in interior construction assemblies. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI (metric) values given in parentheses are provided for information purposes only. 1.3 The following safety hazards caveat pertains only to the test methods portion, Sections 9 and 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Nonstructural Steel Framing Members

BS 4592-3:2006 工业用地面和梯板.冷成型金属厚板.规范

This part of BS 4592 specifies requirements for the design, manufacture, supply and installation of cold formed metal planks intended for use in industrial flooring and stair treads. It is not applicable where access to machinery is required, in which case the requirements of BS EN ISO 14122 apply. NOTE 1 Annex A gives additional recommendations for installation of planks. NOTE 2 For the common requirements for industrial flooring and stair treads, see BS 4592-0. In addition to the definitive requirements, this standard also requires the items detailed in BS 4592-0:2006, Clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied.

Industrial type flooring and stair treads - Cold formed metal planks - Specification

BS 4592-1:2006 工业用地面和梯板.开放金属格栏栅.规范

This part of BS 4592 specifies requirements for the design, manufacture, supply and installation of metal open bar gratings intended for use in industrial flooring and stair treads. It is not applicable where access to machinery is required, in which case the requirements of BS EN ISO 14122 apply. NOTE For the common requirements for industrial flooring and stair treads, see BS 4592-0. In addition to the definitive requirements, this standard also requires the items detailed in BS 4592-0:2006, Clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied.

Industrial type flooring and stair treads - Metal open bar gratings - Specification

BS 4592-2:2006 工业用地面和梯板.金属网栏栅.规范

This part of BS 4592 specifies requirements for the design, manufacture, supply and installation of expanded metal gratings intended for use in industrial flooring and stair treads. It is not applicable in cases where access to machinery is required, in which case the requirements of BS EN ISO 14122 apply. NOTE 1 Annex A gives additional recommendations for installation of gratings. NOTE 2 For the common requirements for industrial flooring and stair treads, see BS 4592-0. In addition to the definitive requirements, this standard also requires the items detailed in BS 4592-0:2006, Clause 4 to be documented. For compliance with this standard, both the definitive requirements and the documented items have to be satisfied.

Industrial type flooring and stair treads - Expanded metal gratings - Specification

KS D ISO 10721-1:2006 钢结构.第1部分:材料和设计

이 규격은 건물 내 강 구조물 강재와 설계 적용에 관한 원칙 및 일반 규정에 대해 기술하고

Steel structures-Part 1:Materials and design

KS D ISO 10721-2:2006 钢结构.第2部分:结构和架设

규격은 복합강과 콘크리트 구조물에서의 철골공사를 포함한 ISO 10721-1과 관련하여 설

Steel structures-Part 2:Fabrication and erection

ANSI/SJI CJCOSP-1.0-2006 CJ系列合成钢横梁标准实践用标准规范和法规

This new standard covers the design and use of open web steel joists in composite construction utilizing field applied shear connectors between the top chord and the overlying concrete slab to allow the steel joist and slab to act together as an integral unit after concrete has adequately cured.

Standard Specifications and Code of Standard Practice for Composite Steel Joists, CJ-Series

DIN EN 14783:2006 屋顶, 外垫及内垫用全支撑钢板及钢条. 产品规范及要求; 英文版本 DIN EN 14783: 2006-12

This European Standard specifies the terminology, requirements and test methods for metal coil, strip, and flat sheets and factory made pieces intended for fully supported applications in roofing and wall cladding or lining. It does not apply to products manufactured on site. This European Standard covers fully-supported aluminium, copper, lead, steel, stainless steel and zinc products with or without coatings, e.g. metallic, organic, inorganic or multi-layer (see Annex A). This European Standard also includes rules for marking, labelling and evaluation of conformity. Requirements concerning acoustical and insulation properties are not considered in this European Standard. This European Standard does not include calculation or design requirements with regards to the works, installation techniques or the performance of the installed products.

Fully supported metal sheet and strip for roofing, external cladding and internal lining - Product specification and requirements; English version of DIN EN 14783:2006-12

BS 1722-1:2006 栅栏.金属防护网用规范

This part of BS 1722 specifies requirements for chain link fences and gates and gateposts for use with chain link fences. The gates specified are steel with a provision for chain link infill or other infill if required by the purchaser. This standard specifies requirements for fences up to 2.5 m in height with a chain link mesh infill. For other security fences, refer to BS 1722-10, BS 1722-12 and BS 1722-14, and for chain link fences for tennis court surrounds refer to BS 1722-13. This standard specifies a method of allocating a reference code to each type of fence, indicating its height, the type and weight of infill, and the materials of the posts and the type of wire coating. This standard is divided into requirements for the material components for fences and for installation of the fences. This standard also includes requirements for protective treatments. However, maintenance requirements for the fence after installation are outside the scope of this standard. This standard includes requirements for sizes of components, together with the permissible tolerances on size. These are minimum requirements, and it will normally be acceptable to use larger sizes, except if this could adversely affect the fitting of components, or if replacement parts are required to match with those already present.

Fences - Specification for chain link fences

BS 1722-8:2006 栅栏.低碳钢链条链接栅栏和篱笆用规范

This part of BS 1722 specifies requirements for mild steel (low carbon steel) continuous bar fences for farm animal containment applications and welded hurdle fences of continuous bar type. A range of five specifications of fence of both types available, in three heights, is listed in Table 1 and Table 3. Requirements for the construction of suitable gates for these fences is given in Clause 5, which states certain functional requirements for the designs, but does not specify the designs in detail. A list of information that should be obtained from the purchaser at the time of enquiry and/or order is given in Annex A.

Fences - Specification for mild steel (low carbon steel) continuous bar fences and hurdles

BS 1722-2:2006 栅栏.应变金属丝和金属丝网栅栏用规范

This part of BS 1722 specifies requirements for the construction and installation of general pattern and dropper pattern strained wire fences and rectangular wire mesh fences, including mild steel or high tensile woven wire fencing, welded mesh fencing, hexagonal wire netting fences of the general pattern, and spring steel wire pattern fences where the mesh is fixed onto spring steel line wires. This standard includes requirements for protective treatments. However, maintenance requirements of the fence after installation are outside the scope of this standard. NOTE Figure 1 illustrates the general characteristics of strained wire fences. It is not intended to illustrate any particular requirements of this standard but provides guidance as to the general layout of a typical fence, and on the terminology associated with this form of fencing.

Fences.Part 2:Specification for strained wire and wire mesh netting fences

BS 1722-14:2006 栅栏.开放筛网钢片栅栏用规范

This part of BS 1722 specifies requirements for the following categories of open mesh steel panel fences: a) Category 1: general purpose fences up to 2 400 mm high. b) Category 2: security fences at least 2 400 mm high. c) Category 3: high security fences at least 3 000 mm high. d) Category 4: extra high security fences at least 3 000 mm high. Requirements for the performance of panel fences for this standard are based upon loadings described in Clause 5. Maintenance of the fence after installation is outside the scope of the standard.

Fences - Specification for open mesh steel panel fences

BS 1722-12:2006 栅栏.钢制栅栏用规范

This part of BS 1722 specifies requirements for steel palisade fences and gates for general purposes (“GP” fences) in corrugated and angle pales for heights up to 2.4 m, and for security purposes (“SP” fences) in corrugated pales for heights of 3.0 m and 3.6 m, all with posts at 2.75 m centres. This standard also covers fences between 2.4 m and 3.0 m in height with components constructed to the SP specification.

Fences – Part 12: Specification for steel palisade fences