供水、排水器材设备标准-分析测试百科网

NF P40-201-1-2:2012 建筑工程.居民建筑物卫生管道.第1-2部分:材料选择的通用规则

Building works - Sanitary plumbing in buildings - Part 1-2 : general criteria for selection of materials

ICS: 91.140.70;91.140.80
CCS: Q81
发布: 2012-12-01
实施: 2012-12-21

NF P40-201-1-1-3:2012 建筑工程.建筑物卫生管道.第1-1-3部分:卫生设备和卫生温水产品设备.承包标书的技术模型条款

Building works - Sanitary plumbing in buildings - Part 1-1-3 : sanitary equipments and sanitary warm water production equipments - Contract bill of technical model clauses

ICS: 91.140.70;91.140.80
CCS: Q81
发布: 2012-12-01
实施: 2012-12-21

DIN 19901:2012 轻质液体和油脂分离装置.结构稳定性和稳固性的验证

Installations for separation for light liquids and greases - Verification of structural stability and steadiness

ICS: 13.060.99;91.010.30
CCS: Q81
发布: 2012-12
实施

BS EN 232:2012 浴缸. 连接尺寸规格

Baths. Connecting dimensions

ICS: 91.140.70
CCS: Q81
发布: 2012-11-30
实施: 2012-11-30

BS EN 251:2012 淋浴盆. 连接尺寸

Shower trays. Connecting dimensions

ICS: 91.140.70
CCS: Q81
发布: 2012-11-30
实施: 2012-11-30

NF E29-591-6:2012 铜和铜合金.卫生洁具.第6部分:推合座末端配件

Copper and copper alloys - Plumbing fittings - Part 6: fittings with push-fit ends

ICS: 23.040.40
CCS: Q81
发布: 2012-11-01
实施: 2012-11-24

CJ/T 409-2012 玻璃钢化粪池技术要求

本标准规定了玻璃钢化粪池（以下简称“化粪池”）的原材料、型号与构造、要求、试验方法、检验规则、标志、包装、运输和贮存。本标准适用于以玻璃纤维和不饱和聚酯树脂为主要原材料制作成型的化粪池。

Technical requirement of fiber-glass reinforced plastic septic tank

ICS
CCS: Q81
发布: 2012-11-01
实施: 2013-01-01

DIN CEN/TS 12666-2:2012 非压力地下排水和污水管道用塑料管道系统.聚丙烯(PE).第2部分:一致性评估指南.德文版本CEN/TS 12666-2-2012

Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity; German version CEN/TS 12666-2:2012

ICS: 23.040.01;93.030
CCS: Q81
发布: 2012-11
实施

EN 12201-3:2011+A1:2012 供水和压力排水和排污用塑料管道系统.聚乙烯(PE).第3部分:管件

This European Standard specifies the characteristics of fittings made from polyethylene (PE 100 and PE 80) intended for the conveyance of water for human consumption, raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. NOTE 1 For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to 5.6 of this part of EN 12201. Components manufactured for water for other purposes, drainage and sewerage may not be suitable for water supply for human consumption. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 1, 2,4 and 5 of EN 12201, it is applicable to PE fittings, their joints and to joints with components of PE and other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to 25 bar 1); b) an operating temperature of 20 °C as a reference temperature; c) buried in the ground; d) sea outfalls; e) laid in water; f) above ground, including pipes suspended below bridges. NOTE 2 For applications operating at constant temperature greater than 20 °C and up to 40 °C, see Annex A of EN 12201-1:2011. EN 12201 (all parts) covers a range of allowable operating pressures and gives requirements concerning colours and additives. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes. These fittings can be of the following types: a) fusion fittings; 1) electrofusion fittings; 2) spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion); 3) socket fusion fittings (see Annex A); b) mechanical fittings; 1) compression fittings; 2) flanged fittings; c) fabricated fittings (see Annex B).

Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 3: Fittings