Q81 供水、排水器材设备 标准查询与下载

ANSI/NSF 61(i94)-2012 NSF/ANSI 61标准.饮用水系统元件:健康效应

NSF/ANSI 61 - Drinking Water System Components: Health Effects

ASTM C655M-12b 钢筋混凝土D型承重涵洞、雨水道和污水管的标准规格(公制)

1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts. 1.2 This specification is the metric counterpart of Specification C655. Note 1???Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C507M-12 钢筋混凝土制椭圆形涵管、雨水管和污水管用标准规范(公制)

1.1 This specification covers reinforced elliptically shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts. 1.2 Pipe designed for placement with the major axis horizontal shall be designated as “Horizontal Elliptical Pipe.” Pipe designed for placement with the major axis vertical shall be designated as “Vertical Elliptical Pipe.” 1.3 This specification is the SI companion to Specification C507. Note 18212;This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site.

Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C506M-12 钢筋混凝土制拱形涵洞,雨水道和污水管标准规格(公制)

1.1 This specification covers reinforced arch-shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts. 1.2 This specification is the SI companion to Specification C506. Note 18212;This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to the construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site.

Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)

ANSI/AWWA F110-2012 饮用水的紫外线消毒系统

This standard sets the minimum requirements for closed-vessel UV disinfection systems and equipment elements used for drinking water disinfection of Cryptosporidium, Giardia, and viruses. It does not include wastewater, reuse, or advanced oxidation treatment. Equipment and elements covered under this standard include UV reactors, related appurtenances and reactor validation.

Ultraviolet Disinfection Systems for Drinking Water

ANSI/AWWA C704-2012 自来水厂用推进式计量表

This standard describes the various types and classes of propeller meters in sizes 2 in. (50 mm) through 72 in. (1,800 mm) for waterworks applications. These meters register by recording the revolutions of a propeller set in motion by the force of flowing water striking the blades.

Propeller-Type Meters for Waterworks Applications

ASTM C361-12 钢筋混凝土低水头压力管的标准规格

1.1 This specification covers reinforced concrete pipe intended to be used for the construction of pressure pipelines with low internal hydrostatic heads generally not exceeding 125 ft. 1.2 This specification is the inch-pound companion to Specification C361; therefore, no SI equivalents are presented in the specification.Note 1???Field tests on completed portions of the pipeline are not covered by this specification for the manufacture of the pipe but should be included in specifications for pipe laying.

Standard Specification for Reinforced Concrete Low-Head Pressure Pipe

ASTM C1577-12 符合AASHTO LRFD设计要求的涵洞、雨水道和下水道所用的预制钢筋混凝土整体方形管的标准规格

1.1 This specification covers single-cell precast reinforced concrete box sections cast monolithically and intended to be used for the construction of culverts and for the conveyance of storm water, industrial wastes and sewage.Note 1???This specification is primarily a manufacturing and purchasing specification. However, standard designs per the AASHTO LRFD Bridge Design Specifications are included and the criteria used to develop these designs are given in Appendix X1. The successful performance of this product depends upon the proper selection of the box section, bedding, backfill, and care that the installation conforms to the construction specifications. The purchaser of the precast reinforced concrete box sections specified herein is cautioned that proper correlation of the loading conditions and the field requirements with the box section specified, and provision for inspection at the construction site, are required. 1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD

ASTM C76-12 钢筋混凝土制下水道、雨水管和污水管标准规格

1.1 This specification covers reinforced concrete pipe intended to be used for the conveyance of sewage, industrial wastes, and storm water, and for the construction of culverts. 1.2 This specification is the inch-pound companion to Specification C76M; therefore, no SI equivalents are presented in this specification. Reinforced concrete pipe that conform to the requirements of C76M, are acceptable under this Specification C76 unless prohibited by the Owner. Note 18212;This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that installation conforms to the construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site. Note 28212;Attention is called to the specification for reinforced concrete D-load culvert, storm drain, and sewer pipe (Specification C655).

Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C655-12 钢筋混凝土D型承重涵管、雨水管和污水管的标准规格

1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts. 1.2 A complete metric companion to Specification C655 has been developedSpecification C655M; therefore, no metric equivalents are presented in this specification. Note 18212;Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

ASME B16.29-2012 可锻铜和可锻铜合金软钎焊连接排水配件.排水、排渣与放气(DWV)

Wrought Copper & Wrought Copper Allow Solder Joint Drainage Fittings - DWV

ANSI/NSF 53(i86)-2012 饮用水处理单元.健康效应

Drinking water treament units - Health effects

ANSI/NSF 40(i25r2)-2012 住宅污水处理系统

Residential wastewater treatment systems

ASTM D3753-12 玻璃纤维增强聚酯人孔和导水井的标准规格

1.1 This specification covers glass fiber-reinforced polyester manholes and wetwells for use primarily in sanitary and storm sewer applications. 1.2 The values given in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information purposes only. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 18212;There is no known ISO equivalent to this standard.

Standard Specification for Glass-Fiber-Reinforced Polyester Manholes and Wetwells

ANSI/AWWA D121-2012 蓄水用螺栓连接的地上热固性玻璃纤维增强塑料嵌板式贮水池

This standard describes the design, fabrication, installation, inspection, and testing of bolted aboveground thermoset fiberglass-reinforced plastic (FRP) panel-type tanks for potable water. Requirements for the fabrication, handling, construction, and testing of FRP panels, concrete and steel foundation structure, foundation, and accessories are included.

Bolted Aboveground Thermosetting Fiberglass-Reinforced Plastic Panel-Type Tanks for Water Storage

ASTM C655-12a 钢筋混凝土D型承重涵洞、雨水道和污水管标准规格

1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts. 1.2 A complete metric companion to Specification C655 has been developed???Specification C655M; therefore, no metric equivalents are presented in this specification. Note 1???Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

ANSI/NSF 46(i21)-2012 污水处理用组件和设备的评估

Evaluation of components and devices used in wastewater treatment systems

ANSI/ASME A112.18.1-2012 管道装置连接件

Plumbing Fixture Fittings

GOST 31921-2012 管道系统连接用铜和铜合金毛细管焊接配件的焊料.等级

Solders for capillary soldering of fittings of copper and copper alloys for connecting the pipelines systems. Grades

ANSI/ASTM F2947:2012 卫生下水道应用件150 至 1500 mm [6 至 60 in]环形波纹轮廓-管壁聚乙烯(PE)管和配件规格

Specification for 150 to 1500 mm [6 to 60 in] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications