Q81 供水、排水器材设备 标准查询与下载

ASTM C506-12 钢筋混凝土制拱形涵管、雨水管和污水管标准规格

1.1 This specification covers reinforced arch-shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts. 1.2 This specification is the inch-pound companion to C506M; therefore, no SI equivalents are presented in the specification. Note 18212;This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to the construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site.

Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe

ASTM C506M-12a 钢筋混凝土制拱形涵洞、雨水道和污水管标准规格(公制)

1.1 This specification covers reinforced arch-shaped concrete pipe to be used for the conveyance of sewage, industrial wastes, storm water, and for the construction of culverts. 1.2 This specification is the SI companion to Specification C506. Note 1???This specification is a manufacturing and purchase specification only, and does not include requirements for bedding, backfill, or the relationship between field load condition and the strength classification of pipe. However, experience has shown that the successful performance of this product depends upon the proper selection of the class of pipe, type of bedding and backfill, and care that the installation conforms to the construction specifications. The owner of the reinforced concrete pipe specified herein is cautioned that he must correlate the field requirements with the class of pipe specified and provide inspection at the construction site.

Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)

ASTM C890-12 用于设计最小负荷结构的整体或分段预制混凝土贮水和废水管道的标准实施规程

1.1 This practice describes the minimum loads to be applied when designing monolithic or sectional precast concrete water and wastewater structures with the exception of concrete pipe, box culverts, utility structures, and material covered in Specification C478. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater Structures

ASTM C655M-12 钢筋混凝土D型承重涵管,雨水管和污水管规格(公制)

1.1 This specification covers reinforced concrete pipe designed for specific D-loads and intended to be used for the conveyance of sewage, industrial wastes, and storm water and for the construction of culverts. 1.2 This specification is the metric counterpart of Specification C655. Note 18212;Experience has shown that the successful performance of this product depends upon the proper selection of the pipe strength, the type of bedding and backfill, the care that the installation conforms to the construction specifications, and provision for adequate inspection at the construction site. This specification does not include requirements for bedding, backfill, the relationship between field load conditions and the strength designation of pipe, or durability under unusual environmental conditions. These requirements should be included in the project specification.

Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

ANSI/AWWA B101-2012 预涂型过滤器介质

Precoat Filter Media

ANSI/AWWA D121-2012 蓄水用螺栓连接的地上热固性玻璃纤维增强塑料嵌板式贮水池

This standard describes the design, fabrication, installation, inspection, and testing of bolted aboveground thermoset fiberglass-reinforced plastic (FRP) panel-type tanks for potable water. Requirements for the fabrication, handling, construction, and testing of FRP panels, concrete and steel foundation structure, foundation, and accessories are included.

Bolted Aboveground Thermosetting Fiberglass-Reinforced Plastic Panel-Type Tanks for Water Storage

ANSI/NFPA 13D-2012 单户和双户住宅和预制房舍中自动喷淋系统的安装标准

1.1* Scope. 1.1.1 This standard shall cover the design, installation, and maintenance of automatic sprinkler systems for protection against the fire hazards in one- and two-family dwellings and manufactured homes. 1.1.2 This standard assumes that the sprinkler system is designed to protect against a fire originating from a single ignition location.

Standard for the Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes

ASTM C1417-12 直接设计的钢筋混凝土污水管、雨水管和涵管制造的标准规格

1.1 This specification covers the manufacture and acceptance of precast concrete pipe designed to conform to the owner's design requirements and to ASCE 15 or an equivalent design specification. 1.2 This specification is the companion to SI Specification C1417M; therefore, no SI equivalents are presented in this specification.

Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design

BS 8551:2011 临时用水供应和分销网的提供和管理(不包括法定突发事件的规定).实施规程

This British Standard gives recommendations and guidance on the provision and management of temporary water supplies and distribution networks to ensure the water supplied to users is wholesome.It is applicable to situations when a permanent supply is not available or not required,for example,at building sites and outdoor public events,or when there is an interruption in the public mains water supply.

Provision and management of temporary water supplies and distribution networks (not including provisions for statutory emergencies). Code of practice

BS DD CEN ISO/TS 22391-7:2011 热水和冷水设备用塑料管道系统.耐热聚乙烯(PE-RT).用于符合性评估的指导

Plastics piping systems for hot and cold water installations. Polyethylene of raised temperature resistance (PE-RT). Guidance for the assessment of conformity

NF P16-364-3:2011 地下非压力排水和排污管网更新用塑料管道系统.第3部分:紧配合管用衬层

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 3 : lining with close-fit pipes.

NF D18-230:2011 饮水装置用挠性软管总成.功能要求和试验方法

Flexible hose assemblies in drinking water installations - Functional requirements and test methods.

DIN 1986-4:2011 民用地面排水系统.第4部分:不同材料排水管道和配件的应用领域

Drainage systems on private ground - Part 4: Fields of application of sewage pipes and fittings of different materials

DIN EN 13618:2011 饮用水装置软管组件.功能要求和试验方法.德文版 EN 13618-2011

This European Standard specifies the requirements and test methods for materials, dimensiona and function for flexible hose assemblies, braided or not , designed for use with drinking water with an allowable maximum operating oressure (PMA) of 1 MPa and maximum operating temperature 70

Flexible hose assemblies in drinking water installations - Functional requirements and test methods; German version EN 13618:2011

ISO 19893:2011 塑料管道系统.热水和冷水用热塑性塑料管道和接头.安装组件耐热循环性的试验方法

Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling

BS EN 12201-3:2011+A1:2012 供水、压力下排水及污水用塑料管道系统.聚乙烯(PE).配件

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fittings

BS EN 12201-1:2011 供水,排水和污水压力塑料管道系统.聚乙烯(PE).总则

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). General

BS EN 12201-5:2011 供水,排水和污水压力塑料管道系统.聚乙烯(PE).系统适用性

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fitness for purpose of the system

BS EN 12201-3:2011 供水,排水和污水压力塑料管道系统.聚乙烯(PE).配件

Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE). Fittings

NF P16-360*NF EN ISO 13260:2011 无压排水和污水系统用热塑管路系统.温度周期变化和外部负载阻力测试方法.

Thermoplastics piping systems for non-pressure underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading.