Q81 供水、排水器材设备 标准查询与下载

DIN EN 14154-3:2011 水表.第3部分:试验方法和设备;德文版本EN 14154-3-2005+A2-2011

This document applies to water meters intended for residential,commercial,light industrial and industrial use,and specifies the test parameters and the test methods for water meters,irrespective of the design technologies ,as specified in EN 14154-1-2005+A2,used to meter the actual volume of clean cold potable water or heated water,flowing through a fully charged,closed conduit.These water meters shall incorporate devices,which indicate the integrated volume. In the case where water meters having a value of Q＞160m/h,the test schedule may make provisions for modification of the Reference Conditions,to meet individual test laboratory limitations,when testing specifically for endurance or for performance under Influence Quantities. Meters thus tested shall be marked so as to unambiguously indicate part compliance with this document. To augment this marking the meter manufacturer shall, in addition, be obliged to fully disclose the specific non compliance(s) due to the test laboratory limitations.

Water meters - Part 3: Test methods and equipment; German version EN 14154-3:2005+A2:2011

BS EN ISO 11296-4:2011 地下无压排水管网和污水管网翻新用塑料管道系统.紧配合管用衬层

This part of ISO 11296, in conjunction with ISO 11296-1, specifies requirements and test methods for curedin- place pipes and fittings used for the renovation of underground non-pressure drainage and sewerage networks. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials and other process-related plastics components (see 5.1).

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. Lining with cured-in-place pipes

BS EN ISO 11296-1:2011 地下无压排水管网和污水管网翻新用塑料管道系统.综述

This part of ISO 11296 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground non-pressure drainage and sewerage networks, which are operated as gravity systems and subjected to a maximum surcharge pressure of 0,5 bar). It is applicable to pipes and fittings as manufactured, as well as to the installed plastics lining system; it is not applicable to the existing pipeline or any annular filler. This part of ISO 11296 establishes the general requirements common to all relevant renovation techniques (see 3.1.2).

Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks. General

BS EN ISO 11298-1:2011 地下供水网翻新用塑料管道系统.总则

This part of ISO 11298 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to cover sprayed coatings, the existing pipeline or any annular filler. This part of ISO 11298 gives the general requirements common to all relevant renovation techniques.

Plastics piping systems for renovation of underground water supply networks. General

BS EN ISO 11296-3:2011 地下无压排水和污水管线翻新用塑料管道系统.紧密配合管衬里

This part of ISO 11296, in conjunction with ISO 11296-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of non-pressure drainage and sewerage networks. It applies to pipes and fittings made of polyethylene (PE) or unplasticized poly(vinyl chloride) (PVC-U). It is applicable to the plastic lining system only. It is not applicable to the requirements for the existing pipeline.

Plastics piping systems for renovation of under ground non-pressure drainage and sewerage networks. Lining with close-fit pipes

BS ISO 25780:2011 有压和无压供水,灌溉,排水用塑料管道系统.基于不饱和聚酯(UP)树脂的玻璃纤维增强热固性塑料(GRP)系统.用顶升技术安装带有柔性接头的管子

Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage. Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin. Pipes with flexible joints intended to be installed usin

BS EN ISO 11298-3:2011 地下供水网翻新用塑料管道系统.无缝衬管衬里

This part of ISO 11298, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of water supply networks, which transport water intended for human consumption, including raw water intake pipelines. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.

Plastics piping systems for renovation of underground water supply networks. Lining with close-fit pipes

BS ISO 22158:2011 水表的输入/输出协议与电子接口.要求

Input/output protocols and electronic interfaces for water meters. Requirements

ISO 22158:2011 水表用输入/输出协议与电子接口.要求

This International Standard specifies the minimum communication requirements for water meters which have the capability to exchange or provide data by means of an electronic interface. This International Standard only specifies the interface conditions present at the electrical and electronic connections of water meters and does not prescribe any specific equipment such as transponders and inductive pads, which might be connected to the water meter for automatic meter reading or remote meter reading purposes.

Input/output protocols and electronic interfaces for water meters - Requirements

ISO 21307:2011 塑料管道和配件.配气和配水系统的建造用聚乙烯(PE)管道和配件用对焊熔接程序

This International Standard establishes general principles regarding the procedure used in the construction and quality assessment of butt fusion joints incorporating fittings (ISO 8085-2) and pipes used in the construction of gas (ISO 4437) and water (ISO 4427) distribution systems made with equipment that complies with ISO 12176-1 and installed in accordance with ISO/TS 10839, relevant codes of practice, national regulations or industry guidance. Specifically, this International Standard specifies a number of proven butt fusion jointing procedures for pipes and fittings with a wall thickness up to and including 70 mm. This International Standard takes into consideration the materials and components used, the fusion jointing procedure and equipment and the quality assessment of the completed joint. It can be applied in conjunction with appropriate national regulations and standards. NOTE It is important that pipe or fitting manufacturers and equipment manufacturers be consulted when undertaking butt fusion jointing of pipes with a wall thickness greater than 70 mm.

Plastics pipes and fittings - Butt fusion jointing procedures for polyethylene (PE) pipes and fittings used in the construction of gas and water distribution systems

ISO 25780:2011 压力与非压力水源,灌溉,排税或排污系统用塑料管道系统.基于不饱和聚酯树脂之上的玻璃增强性热凝塑料(GRP)系统.将要安装的附带挠性接头的管道

This International Standard specifies the properties of the piping system and its components made from glassreinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for water supply, irrigation, drainage or sewerage systems with or without pressure. This International Standard is applicable to GRP-UP piping systems, with flexible joints, intended to be installed using jacking techniques. It specifies the characteristics of pipes made from GRP-UP, with or without aggregates or fillers and also specifies the test parameters for the test methods referred to in this International Standard. NOTE Pipes referred to in this International Standard are, because of their intended use, required to have a minimum nominal stiffness of at least SN 20000 (see 5.2.1). This International Standard is applicable to pipes and joints with a size range from DN100 to DN4000 which are intended to be used for the conveyance of water or sewage at temperatures up to 50 ℃, with or without pressure. It covers requirements to prove the design of the joint and specifies type test performance requirements for the joints as a function of the declared nominal pressure rating of the pipeline system and the required joint deflection capability of the system. GRP-fittings, used between pipe systems covered by this International Standard, shall be in accordance with ISO 10639 for water supply systems or ISO 10467 for drainage and sewerage systems, as applicable. In a pipe-work system, pipes of different nominal pressure and stiffness ratings may be used together.

Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin - Pipes with flexible joints intended to be installed us

DIN EN 15200 Berichtigung 1:2011 卫生设备.多功能淋浴间;德文版本EN 15200-2007,DIN EN 15200-2007-08的技术勘误;德文版本EN 15200-2007/AC-2009

Sanitary appliances - Multifunction shower cabinets; German version EN 15200:2007, Corrigendum to DIN EN 15200:2007-08; German version EN 15200:2007/AC:2009

EN 13508-2:2003+A1:2011 建筑物外排水和下水道系统的调查和评估.第2部分:视觉检查编码系统

This European Standard is applicable to the investigation and assessment of drain and sewer systems outside buildings. It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where the wastewater leaves a building or roof drainage system, or enters a road gully, to the point where it is discharged into a treatment works or receiving water. Drains and sewers below buildings are included provided that they do not form part of the drainage system of the building. This part of the European Standard specifies a coding system for the description of the internal condition of drains, sewers, manholes and inspection chambers identified through visual inspection. Where appropriate, it can also be used for pressure and vacuum systems in accordance with the requirements of the employing authority. Visual inspection of drain and sewer systems can be carried out as part of the investigation in order to undertake the assessment. This part of the European Standard does not generally specify requirements for carrying out inspections.

Investigation and assessment of drain and sewer systems outside buildings - Part 2: Visual inspection coding system

DIN EN 1113:2011 卫浴龙头.1型和2型给水系统用卫生设备的淋浴软管.一般技术规范.德文版本EN 1113-2008+A1-2011

This European Standard specifies: — the dimensional, leaktightness, mechanical and hydraulic characteristics with which shower hoses shall comply; — the procedures for testing these characteristics. This European Standard applies to shower hoses of any material used for ablutionary purposes and intended for equipping and supplementing sanitary tapware for baths and showers. This European Standard applies to shower hoses connected downstream of the obturator of the tapware. Hoses which are an integral part of sanitary tapware (sink and wash basin mixing valves) or hoses intended to connect sanitary tapware to the water supplies are not covered by this European Standard.

Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification; German version EN 1113:2008+A1:2011

CJ/T 225-2011 埋地排水用钢带增强聚乙烯（PE）螺旋波纹管

本标准规定那个了钢带增强聚乙烯（PE）螺旋波纹管的术语和定义、符号、缩略语、原料、分级与标记、管材结构与连接方式、要求、试验方法、检验规则、标志、运输和贮存。 本标准适用于输送介质温度不大于45℃的雨水、污水等埋地排水管道。

Metal reinforced polyethylene(PE) spiral corrugated pipe for underground sewer

ISO 21003-2:2008/Amd 1:2011 建筑物内冷热水装置用多层管道系统.第2部分:管道.修改件1

Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes; Amendment 1

Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes; Amendment 1

JJG 1065-2011 IC卡节水计时计费器检定规程

本规程适用于以非接触式IC卡为预存费用载体的节水计时计费器的首次检定、后续检定和使用中检查。

Verification Regulation of IC Card Timing and Charging Device for Water Saving

NF D18-208/IN1:2011 卫生用水龙头.1型和2型供水设备的卫生水龙头用淋浴软管.通用技术规范

Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification.

NF P16-363-1:2011 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检验室在内的辅助配件规范

Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1 : specifications for ancillary fittings including shallow inspection chambers.

NF D12-216:2011 洗手间和小便冲水箱

WC and urinal flushing cisterns.