Q81 供水、排水器材设备 标准查询与下载

NF D18-208:2011 卫浴龙头.卫浴龙头淋浴软管供水系统1型和2型.通用技术规范.

Sanitary tapware - Shower hoses for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification.

DIN EN 476:2011 废水,排水用管的通用要求;德文版本EN 476-2011

This European Standard specifies general requirements for components inside and outside buildings (see EN 12056-1)such as pipes, fittings and manholes with their respective joints intended for use in discharge pipes, drains and sewers which operate as gravity systems allowing for a maximum pressure of 40 kPa.

General requirements for components used in drains and sewers; German version EN 476:2011

BS EN 13598-1:2010 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).包括浅层检验室在内的辅助配件规范

This European Standard specifies the definitions and requirements for ancillary fittings of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP), and polyethylene (PE) intended to be used in non-pressure underground drainage and sewerage systems, conforming to EN 476: a) outside the building structure (application area code “U”), reflected in the marking of products by “U”, and b) both buried in ground within the building structure (application area code “D”) and outside the building structure (application area code “U”), reflected in the marking of products by “UD”. It also specifies the test parameters for the test methods referred in this standard. The ancillary fittings covered by this standard are the following: ? sealed access fittings; ? rodding point covers; ? rodding tees; ? mechanical saddles; ? inspection chambers for shallow non-roadway applications to a maximum depth of 1,25 m. NOTE 1 Inspection chambers as defined in 6.1.3 of EN 476:1997 have a riser with a DN/ID less than 800 mm. NOTE 2 Deep inspection chambers and manholes for application area U are specified in Part 2 of this standard. The fittings can be manufactured by various methods e.g. injection moulding, rotational moulding, spiral winding or fabricated from components made to other standards. The jointing can be with: ? elastomeric ring seal joint; ? cemented joint for PVC-U; ? welded joint for PP and PE. NOTE 3 Pipes, fittings and other components conforming to any of the plastics products standards listed in Clause 2 can be used with ancillary fittings conforming to this standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 6.

Plastics piping systems for non-pressure underground drainage and sewerage. Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE). Specifications for ancillary fittings including shallow inspection chambers

JIS C 9335-2-84:2011 家用和类似用途电气设备.安全性.第2-84部分:卫生间设备的详细要求

Household and similar electrical appliances -- Safety -- Part 2-84: Particular requirements for appliances used with toilets

CJ/T 363-2011 建筑同层排水部件

本标准规定了建筑同层排水最主要部件的管材和管件、卫生器具、隐蔽式安装部件、地漏和存水弯的试验方法、检验规则、标志和标识、包装、运输和贮存。 本标准适用于民用和工业建筑同层排水部件的设计、生产和检测。

Components for same-floor drainage system in buildings

NF P16-109:2011 排水沟和下水道的修理和维护用工艺分类和特征描述

Classification and characteristics of techniques for renovation and repair of drains and sewers.

NF D11-201/A1:2011 家庭管理.可供残疾人使用的洗手盆装配和安装条件

Household management - Conditions of assembly and installation of wash basins for accomodating handicapped persons.

YB/T 4223-2010 给水加热器用奥氏体不锈钢焊接钢管

Austenitic stainless steel welded steel pipes for feedwater heaters

NF P16-100:2011 用于排水管和污水管部件的一般要求

General requirements for components used in drains and sewers.

DIN EN ISO 15877-1:2011 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第1部分:总则(ISO 15877-1-2009 + AMD 1-2010).德文版本EN ISO 15877-1-2009 + A1-2010

This Part of ISO 15877 specifies the general requirements of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application. This Part of ISO 15877 covers a range of service conditions (classes of application), design pressures and pipe dimension classes. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other Parts of ISO 15877 it is applicable to PVC-C pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General (ISO 15877-1:2009 + AMD 1:2010); German version EN ISO 15877-1:2009 + A1:2010

DIN EN ISO 15877-5:2011 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第5部分:系统用途的适当性(ISO 15877-5-2009 + AMD 1-2010).德文版本EN ISO 15877-5-2009 + A1-2010

This Part of ISO 15877 specifies the characteristics of the fitness for purpose of chlorinated poly(vinyl chloride) (PVC-C) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application. This Part of ISO 15877 covers a range of service conditions (application classes) and design pressure classes It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other Parts of ISO 15877 it is applicable to PVC-C pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system (ISO 15877-5:2009 + AMD 1:2010); German version EN ISO 15877-5:2009 + A1:2010

DIN EN 60335-2-109:2011 家用和类似用途电器.安全性.第2-109部分:紫外辐射水处理器具的特殊要求(IEC 60335-2-109-2010);德文版本EN 60335-2-109-2010

Household and similar electrical appliances - Safety - Part 2-109: Particular requirements for UV radiation water treatment appliances (IEC 60335-2-109:2010); German version EN 60335-2-109:2010

DIN EN ISO 15877-3:2011 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第3部分:配件(ISO 15877-3-2009 + AMD 1-2010).德文版本EN ISO 15877-3-2009 + A1-2010

This Part of ISO 15877 specifies the characteristics of fittings made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application. This Part of ISO 15877 covers a range of service conditions (application classes) and design pressure classes. It also specifies the parameters for the test methods referred to in this standard. In conjunction with the other Parts of ISO 15877 it is applicable to PVC-C fittings, their joints and to joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations. This Part of ISO 15877 is applicable to fittings of the following types: - fittings for solvent cement joints; - mechanical fittings; - fittings with incorporated inserts.

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings (ISO 15877-3:2009 + AMD 1:2010); German version EN ISO 15877-3:2009 + A1:2010

DIN CEN/TR 852:2011 用于人类饮用水运输的塑料管道系统.迁移评价.实验室导出迁移值的解释用指南.德文版本CEN/TR 852-2010

Plastics piping systems for the transport of water intended for human consumption - Migration assessment - Guidance on the interpretation of laboratory derived migration values; German version CEN/TR 852:2010

ISO 10639:2004/Amd 1:2011 压力和非承压供水塑料管道系统.不饱和聚酯(UP)树脂基玻璃增强热固性塑料(GRP)系统.修改件1

Plastics piping systems for pressure and non-pressure water supply - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin; Amendment 1

ASME A112.19.3 Update 2-2011 不锈钢管道设备;更新2

Stainless Steel Plumbing Fixtures; Update 2

DIN EN ISO 15877-2:2011 冷热水装置用塑料管道系统.氯化聚氯乙烯(PVC-C).第2部分:管道(ISO 15877-2-2009 + AMD 1-2010).德文版本EN ISO 15877-2-2009 + A1-2010

This Part of ISO 15877 specifies the requirements of pipes made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application. This Part of ISO 15877 covers a range of service conditions (application classes), design pressures and pipe series. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with the other Parts of ISO 15877 it is applicable to PVC-C pipes, their joints and to joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations.

Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes (ISO 15877-2:2009 + AMD 1:2010); German version EN ISO 15877-2:2009 + A1:2010

JIS A 4422:2011 带冲洗装置的马桶座

Toilet seat with shower unit

DIN SPEC 19674-2:2011 供水,压力排水和排污用玻璃纤维增强聚乙烯(PE-GF)制塑料管道系统.第2部分:管道

This part of DIN SPEC 19674 specifies the aspects of pipes made from glass fibre reinforced polyethylene (PE-GF) for the use in pressure piping systems (mains and service pipes), intended for the conveyance of water for human consumption including raw water prior to treatment, drainage and sewerage under pressure, vacuum sewer systems, and water for other purposes. It also specifies the test parameters for the test methods referred to in this specification. In conjunction with the other parts of DIN SPEC 19674 it applies to pipes made from PE-GF, their joints, joints to other parts of the piping system, and with components of other materials intended to be used under the following conditions: a) allowable operating pressure, PFA, up to and including 22 bar; b) an operating temperature of 20 °C as a reference temperature.

Plastics piping systems made from glass fibre reinforced polyethylene (PE-GF) for water supply and for drainage and sewerage under pressure - Part 2: Pipes

DIN 86290:2011 饮用水保护,并考虑到腐蚀和水质用的水车和水工建筑物所应用设施,化学药品和微生物的规程

Facilities and chemical and microbiological procedures used on water vehicles and maritime constructions for drinking water protection, taking corrosion and water quality into consideration