Q82 供气器材设备 标准查询与下载

BS EN 12007-1:2012 天然气基础设施.最大工作压力达到和超过16 bar的管线.通用功能要求

Gas infrastructure. Pipelines for maximum operating pressure up to and including 16 bar. General functional requirements

BS EN 12405-2:2012 煤气表.转换装置.能量转换

Gas meters. Conversion devices. Energy conversion

BS EN 12327:2012 天然气基础设施.压力试验,交付使用和非交付使用过程.功能要求

Gas infrastructure. Pressure testing, commissioning and decommissioning procedures. Functional requirements

NF D36-510*NF EN 298:2012 带或不带风扇的气体燃烧器和燃气设备用自动气体燃烧器控制系统

Automatic burner control systems for burners and appliances burning gaseous or liquid fuels.

DIN 30692-2:2012 煤气分配和安装装置用隔膜. 第2部分:增强弹性隔膜材料的要求和检验

Diaphragms for gas distribution and installation - Part 2: Requirements and test of reinforced diaphragm material

DIN EN 30-1-2:2012 家用燃气灶具.安全性.第1-2部分:强制对流式烘炉和/或烤架装置

Domestic cooking appliances burning gas - Safety - Part 1-2: Appliances having forced-convection ovens and/or grills; German version EN 30-1-2:2012

ISO 16486-1:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第1部分:总则

This part of ISO 16486 specifies the general properties of unplasticized polyamide (PA-U) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. and/or mechanical jointing. This part of ISO 16486 establishes a calculation and design scheme on which to base the maximum operating pressure (MOP) of a PA-U piping system.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 1: General

ISO 16486-6:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第6部分:设计,操作和安装实施规程

This part of ISO 16486 specifies a code of practice dealing with unplasticized polyamide (PA-U) piping systems, intended to be buried outside buildings and used for the supply of gaseous fuels. It addresses the common basic principles for gas supply systems. More detailed national standards or codes of practice might exist in the ISO member countries. This part of to the above-mentioned basic principles. It is applicable to mains and service lines, the components of which are prepared for jointing by scraping and/or machining, and gives instructions for the design, storage, handling, transportation, laying conditions and fusion quality control of PA-U pipes and fittings up to and including 250 mm outside diameter, as well as subsequent joint testing, backfilling, pipe system testing, commissioning and decommissioning. The jointing methods covered by this part of ISO 16486 are butt fusion jointing and electrofusion jointing. No special precautions are necessary for areas exposed to the influence of mining and earthquakes other than those precautions mentioned in this part of ISO 16486. It is the responsibility of users of this part of ISO 16486 to take existing and new national regulations into account.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 6: Code of practice for design, handling and installation

ISO 16486-3:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第3部分:配件

This part of ISO 16486 specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers. and/or mechanical jointing. In addition, it lays down dimensional characteristics and requirements for the marking of fittings. In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints, to joints with components of PA-U and to joints with mechanical fittings of other materials, and to the following fitting types: — fusion fittings — electrofusion fittings and butt fusion fittings; — transition fittings.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings

ISO 16486-5:2012 气体燃料供给用塑料管道系统.带有热熔接头和机械接头的不加增塑剂的聚酰胺(PA-U)管道系统.第5部分:系统配件

This part of ISO 16486 specifies the requirements of fitness for purpose of the unplasticized polyamide (PA-U) piping system, intended to be buried and used for the supply of gaseous fuels. It also specifies the definitions of electrofusion and butt fusion joints. This part of ISO 16486 specifies the method of preparation of test piece joints and the tests to be carried out on these joints for assessing the fitness for purpose of the system under normal and extreme conditions. It also specifies the test parameters for the test methods to which it refers. and/or mechanical jointing. In conjunction with the other parts of ISO 16486, it is applicable to PA-U fittings, their joints and to joints with components of PA-U.

Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 5: Fitness for purpose of the system

BS EN 30-1-4:2012 家庭烹调用燃气灶具.安全性.带有自动燃烧控制系统的一个或多个燃烧器的用具

Domestic cooking appliances burning gas. Safety. Appliances having one or more burners with an automatic burner control system

BS EN 126:2012 燃气器具的多功能控制器

Multifunctional controls for gas burning appliances

BS EN 30-1-2:2012 家用炊具燃气.安全性.有强对流烘箱和/或烧烤架的器具

Domestic cooking appliances burning gas. Safety. Appliances having forced-convection ovens and/or grills

DIN EN 30-1-1:2012 家用燃气灶具.第1-1部分:安全性.总则

Domestic cooking appliances burning gas - Part 1-1: Safety - General; German version EN 30-1-1:2008+A2:2010 + AC:2011

ASME B31.8 INTERPRETATIONS-2012 压力管道规程 (包括解释1-16: 1981年9月至2012年3月)

Code for Pressure Piping (Includes Interpretations 1-16: September 1981 Through March 2012)

ANSI Z21.60-2012 固体燃料壁炉中安装的装饰性燃气器具

This standard applies to decorative gas appliances for installation in solid-fuel burning fireplaces, which are constructed entirely of new, unused parts and materials: a. for use with natural gas; b. for use with propane; c. for use with natural and convertible for use with propane gas; d. for manufactured home (US only) or mobile home installation for use with natural and convertible for use with propane gas; and e. for manufactured home (US only) or mobile home installation for use with propane gas only.

Standard for Decorative Gas Appliances for Installation in Solid Fuel Burning Fireplaces (same as CSA 2.26)

ANSI Z21.84-2012 固体燃料壁炉中安装的手工点燃式装饰性燃气装置

These requirements apply to manually lighted, natural gas, decorative gas appliances for installation in solid-fuel burning fireplaces, for use with natural gas only, at a maximum input rating of 90,000 Btu/hr (26 376W), which are constructed entirely of new, unused parts and materials.

Standard for Manually Lighted, Natural Gas Decorative Gas Appliances for Installation in Solid-Fuel Burning Fireplaces

ANSI Z21.21-2012 燃气器具用自动阀(与CSA 6.5b标准相同)

This standard applies to individual automatic valves or valves utilized as parts of automatic gas ignition systems. This standard also applies to commercial\industrial safety shutoff valves, herein after referred to as C/I valves. This standard shall not apply to self-contained water heater, cooking appliance, or room heater thermostats, or self-contained automatic gas shutoff valves for hot water supply systems.

Automatic Valves for Gas Appliances (same as CSA 6.5)

ASME B31.8-2012 气体传输与分配管道系统

Gas Transmission and Distribution Piping Systems

ANSI Z21.18b-2012 燃气器具压力调节器(同CSA 6.3b标准)

This standard applies to individual gas appliance pressure regulators, which are not a part of a combination control, intended for application on individual gas appliances. This standard also applies to negative gas appliance pressure regulators.

Standard for Gas Appliance Pressure Regulators (same as CSA 6.3b)