Q83 供热器材设备 标准查询与下载

KS B 8004-2010 开放式自然通风燃油取暖炉

이 표준은 등유를 연료로 하고 연료 소비량1)이 600 g/h 이하인 자연 통기형 개방식2

Open type natural ventilating oil burning space heaters

KS B 8018-2010 热水锅炉贮水器

이 표준은 온수, 음료용 또는 난방에 사용되는 온수 보일러 및 저탕(貯湯)조 등(간접 가열

Cisterns for hot-water boiler

KS B 8110-2010 密闭存储式燃气热水器

이 표준은 액화 석유 가스 또는 도시가스(이하 가스라 한다.)를 연료로 하는 버너를 가지며

Close storage type gas water heaters

KS B 8022-2010 开放式强制通风燃油加热器的氮氧化物排放量测定方法

이 표준은 연료 소비량이 600 g/h 이하인 강제 통기형 개방식 기름 난로(이하 난로라

Measurement method of NOx emission rate for open type forced draught oil burning space heaters

KS B 8013-2010 半密封式燃油加热器

이 표준은 등유 또는 경유를 연료로 하고 연료 소비량1)이 3 200 g/h 이하인 반밀폐

Semi closed type oil burning space heaters

KS B 8025-2010 热水供暖用地板

이 표준은 80 ℃ 이하의 온수를 사용하여 바닥을 난방하는 패널[이하 온수패널1)이라 한다

Floor panels for hot water heating

KS B 8218-2010 石油管加热器

이 표준은 등유, 경유 또는 중유를 연료로 하는 표시 연료 소비량이 70 kW:252 MJ

Oil burning tube heaters

KS B 8219-2010 燃气管式加热器

이 표준은 액화 석유 가스 또는 도시가스(이하 가스라 한다.)를 연료로 사용하고, 표시 가

Gas burning tube heaters

ISO 22967:2010 强制通风煤气炉

This International Standard specifies the terminology, test procedures and general requirements for the construction and operation of automatic forced draught gas burners, and the provision of related control and safety devices. It is applicable to the following: a) automatic gas burners (hereinafter called “burners”) fitted with a combustion air fan that are equipped as described in Clause 4, intended for use in appliances of different types and operated with fuel gases; b) total pre-mixed burners and nozzle mixed burners; c) single burners with a single combustion chamber, for which, where such burners are fitted to a single appliance, the requirements of the relevant appliance standard also apply; d) single-fuel and dual-fuel burners when operating only on gas; e) the gas function of dual-fuel burners designed to operate simultaneously on gaseous and liquid fuels, which, for the latter, the requirements of ISO 22968 also apply. It is not applicable to burners used in direct fired processes either with defined combustion chamber applications or where the combustion chamber wall surface temperature is greater than 750 °C or the heat-transfer medium temperature is greater than 500 °C.

Forced draught gas burners

BS 5864:2010 额定输入净值不超过70 kW的燃气管道式空气加热器的安装和维修(2类和3类燃气).规范

This Part of BS 5502 gives recommendations for the design, construction and use of agricultural storage tanks and reception pits for livestock slurry. NOTE Further sources of information are given in Appendix A. The titles of the publications referred to in this standard are listed on page 24.

Installation and maintenance of gas-fired ducted air heaters of rated heat input not exceeding 70 kW net (2nd and 3rd family gases). Specification

DIN EN 1319:2010 有鼓风机辅助燃烧的净热输入不超过70 kW的家用燃气驱动空间供热用对流空气加热器.德文版本EN 1319-2009

Domestic gas-fired forced convection air heaters for space heating, with fan-assisted burners not exceeding a net heat input of 70 kW; German version EN 1319:2009

KS B 8400-2-2010 激光和激光相关设备.激光位移测量干涉仪测试方法.第2部分:激光干涉仪的试验方法

이 표준은 이송대의 변위를 측정하는 레이저 간섭계의 특성을 측정하고 평가하는 방법에 대하여

Lasers and laser-related equipments-Test methods for laser interferometers for displacement measurement-Part 2:Test methods for laser interferometers

KS B 8400-1-2010 激光和激光相关设备.激光位移测量干涉仪测试方法.第1部分:稳定连续波激光波长的测试方法

이 표준은 레이저 간섭계의 광원으로 사용되는 주파수가 안정된 연속파 레이저의 발진 주파수

Lasers and laser-related equipments-Test methods for laser interferometers for displacement measurement-Part 1:Test methods for the frequency stability of frequency-stabilized continuous wave lasers

NF E39-010/IN1:2010 集中供热用预隔热粘合管道系统的设计和安装

Design and installation of preinsulated bonded pipe systems for district heating.

NF E39-010:2010 集中供暖用预绝缘粘结管系统的设计和安装.

Design and installation of preinsulated bonded pipe systems for district heating.

BS EN 13203-3:2010 燃气家用产热水器.不超过70 kW热输入的器具和500 l水存储容器.能量消耗评定

This European Standard is applicable to solar supported gas-fired appliances producing domestic hot water. It applies to a system marketed as single unit or a system fully specified by a manufacturer that: ? has a gas heat input not exceeding 70 kW; and ? has a hot water storage capacity not exceeding 500 l; and ? is equipped with at least one solar collector; and ? is, with regard to the solar hydraulic circuit, considered as a forced circulation system (definition according to EN ISO 9488:1999). The appliances covered by this European Standard are described in Annex C. This European Standard does not apply to thermo-siphon or integral collector storage systems (definitions according to EN ISO 9488-1999). NOTE In principle, the energy consumption of thermo-siphon solar preheat systems and integral collector storage preheat systems can also be assessed on the basis of this standard. One appropriate procedure for that purpose is to calculate the temperature level of the domestic hot water withdrawn from the thermal solar system for the reference conditions defined in this standard by using the numerical system model and the thermal solar system performance parameters according to ISO 9459-5. Based on the temperature level of the hot water withdrawn from the store the energy consumption of the gas appliance should be determined. This determination can either be done by means of calculations or by performing a test according to EN 13203-2 and using instead of the cold water inlet temperature the hot water temperature withdrawn from the store. This standard is not intended to assess the performance: ? of the solar collector(s), which should comply with EN 12975-1 and EN 12975-2; and ? thermal solar systems and components, which should comply with EN 12976-1 and EN 12976-2. This European Standard, EN 13203-3, sets out a method for assessing the energy performance of a solar supported appliance. It defines a number of daily tapping cycles for each domestic hot water use, kitchen, shower, bath and a combination of these, together with corresponding test procedures including information about the available solar radiation. It enables the energy performances of different gas-fired appliances to be compared and matched to the needs of the user.

Solar supported gas-fired domestic appliances producing hot water.Appliances not exceeding 70 kW heat input and 500 litres water storage capacity. Part 3: Assessment of energy consumption

BS 5546:2010 额定输入不超过70kW的家用燃气供热水装置的安装和维修规范

This British Standard specifies requirements for the selection, installation, inspection, commissioning and maintenance of gas‑fired water-heating appliances, which have a rated heat input not exceeding 70 kW, based on net calorific value. It applies to water-heating appliances utilizing 1st, 2nd or 3rd family gases designed to operate in the condensing or non‑condensing mode for the supply of hot water for domestic purposes in domestic dwellings or domestic dwellings in commercial premises. This standard does not apply to: a) water-heating appliances with a rated input of over 70 kW; b) hot water supply systems in multiple dwellings supplied from a central source. It does not cover the detailed design and installation of the whole hot water distribution system, which was specified in BS 5449. This standard applies to water-heating appliances which carry a CE mark and also to previously used water-heating appliances which do not carry the CE mark (see 5.3.1).

Specification for installation and maintenance of gas-fired water-heating appliances of rated input not exceeding 70 kW net

DIN EN 15632-3:2010 区域供暖管道.预隔热弹性管道系统.第3部分:带有塑料供水管的非黏结系统.试验方法和要求.德文和英文版本EN 15632-3-2010

District heating pipes - Pre-insulated flexible pipe systems - Part 3: Non bonded system with plastic service pipes - Requirements and test methods; German and English version EN 15632-3:2010

DIN EN 15632-2:2010 区域供暖管道.预隔热弹性管道系统.第2部分:黏结塑料供水管.试验方法和要求.德文和英文版本EN 15632-2-2010

District heating pipes - Pre-insulated flexible pipe systems - Part 2: Bonded plastic service pipes - Requirements and test methods; German and English version EN 15632-2:2010

JIS S 2072 ERRATUM 1:2010 勘误表

ERRATUM