S35 牵引电气设备 标准查询与下载

TB/T 2986-2000 铁路机车牵引电机悬挂抱轴瓦油

本标准规定了以深度脱蜡、精制馏分油和中性油为基础油，加人适量添加剂调制的铁路机车牵引电机悬挂抱轴瓦油的技术要求、取样、包装、标志、贮运。 本标准规定的产品适用于进口和国产内燃、电力机车牵引电机悬挂抱轴瓦的全天候润滑。

Railway locomotive traction motor suspension bearing pad oil

TB/T 2987.2-2000 内燃、电力机车牵引电动机抱轴瓦轴承合金化学分析方法

本标准规定了铁路内燃、电力机车牵引电动机抱轴瓦轴承合金的测定方法。 本标准适用于铁路内燃、电力机车牵引电动机抱轴瓦轴承合金即11-6锡锑轴承合金，合金牌号为ZChSnSbll-6金属元素百分含量的测定。测定范围:Sb10%~12%，Cu5.5%~6.5%，Pb≤0.3 5%

Chemical analysis method for bearing alloys of traction motors of internal combustion and electric locomotives

TB/T 2987.1-2000 内燃、电力机车牵引电动机抱轴瓦铜背合金化学分析方法

本标准规定了铁路内燃、电力机车牵引电动机抱轴瓦铜背合金的测定方法。 本标准适用于铁路内燃、电力机车牵引电动机抱轴瓦铜背合金即5-5-5锡青铜，合金牌号为ZCuSn5Pb5Zn5金属元素含量的测定。测定范围:Sn4.0%~6.0% ，Zn4.0% ~6.0%，Pb4.0%~6.0%。

Chemical analysis method for copper back alloy of bearing bush of internal combustion and electric locomotive traction motor

BS EN 50239:2000 轨道交通.货运牵引车辆无线电遥控系统

This European Product Standard specifies the characteristics of operational and technical requirements for the overall system design as well as safety acceptance and approval, maintenance, modifications and extensions of the radio remote control system for the use in the railway network in relationship with other European Standards. This European Product Standard applies only for the use of radio remote control systems for freight traffic. If the radio remote control system is modified in such a way that the system safety may be compromised it is necessary that safety reviews are carried out throughout the system lifecycle. This European Product Standard is not applicable to existing systems (i.e. those which had already been accepted prior to the creation of this standard). However as far as reasonably practicable this European Product Standard applies to modifications and extensions to existing systems.

Railway applications - Radio remote control system of traction vehicle for freight traffic

BS EN 61881:2000 轨道交通.机车车辆设备.电源电子装置电容器

This International Standard applies to capacitors for power electronics intended to be used on rolling stock. The rated voltage of capacitors covered by this part is limited to 10 000 V. The operating frequency of the systems in which these capacitors are used is usually below 2 500 Hz, while the pulse frequencies may go up to several thousand hertz, in some cases beyond 10 000 Hz. It distinguishes between a.c. and d.c. capacitors. They are considered as components mounted in enclosures. NOTE - This standard covers an extremely wide range of capacitor technologies for numerous applications: overvoltage protection, d.c. and a.c. filtering, switching circuits, d.c. energy storage, auxiliary inverters, etc. The following are excluded from this standard: - capacitors for induction heat-generating plants operating at frequencies between 40 Hz and 24 000 Hz (see IEC 60110); - capacitors for motor applications and the like (see IEC 60252); - capacitors to be used in circuits for blocking one or more harmonics in power supply networks; - small a.c. capacitors as used for fluorescent and discharge lamps (see IEC 61048 and IEC 61049); - capacitors for suppression of radio interference (see IEC 60384-14); - shunt capacitors for a.c. power systems having a rated voltage above 1 000 V (see IEC 60871-1 and IEC 60871-2); - shunt power capacitors of the self-healing type for a.c. systems having a rated voltage up to and including 1 000 V (see IEC 60831-1 and IEC 60831-2); - shunt power capacitor of the non self-healing type for a.c. systems having a rated voltage up to and including 1 000 V (see IEC 60931-1 and IEC 60931-2); - electronic capacitors not used in power circuits (see IEC 60080 and IEC 60166); - series capacitors for power systems (see IEC 60143); - coupling capacitors and capacitors dividers (see IEC 60358); - capacitors for applications requiring energy storage/high current discharge such as photocopies and lasers; - capacitors for microwave ovens. Examples are given in clause 6.

Railway applications - Rolling stock equipment - Capacitors for power electronics

ANSI/IEEE 11:2000 铁路和道路车辆用旋转电机的标准

Applies to rotating electric machinery which forms part of the propulsion and major auxiliary equipment on internally and externally powered electrically propelled rail and road vehicles and similar large transport and haulage vehicles and their trailers where specified in the contract.

Standard for Rotating Electric Machinery for Rail and Road Vehicles

BS EN 50123-7-3:1999 轨道交通.固定设备.直流开关装置.直流牵引系统专用测量、控制和保护设备.绝缘电压传感器和其他电压测量设备

Railway applications - Fixed installations - d.c. switchgear - Measurement, control and protection devices for specific use in d.c. traction systems - Isolating voltage transducers and other voltage measuring devices

BS EN 50123-7-2:1999 轨道交通.固定设备.直流开关装置.直流牵引系统专用测量、控制和保护设备.绝缘电流传感器和电流测量设备

Railway applications - Fixed installations - d.c. switchgear - Measurement, control and protection devices for specific use in d.c. traction systems - Isolating current transducers and current measuring devices

NF F42-123-7-2:1999 轨道交通.固定设备.直流开关装置.第 7部分:直流牵引系统专用测量、控制和保护设备.第2节:绝缘电流传感器和电流测量设备

Railway applications - Fixed installations D.C. switchgear - Part 7 : measurement, control and protection devices for specific use in d.c. traction systems - Section 2 : isolating current transducers and other current measuring devices.

TB/T 2-1999 车辆用票插

本标准规定了票擂的型式与尺寸、技术要求及标记等。 本标准适用于铁道客、货车。

vehicle ticket insert

TB/T 2055-1999 机车真空断路器技术条件

本标准规定了机车及动车组用25kV、50Hz真空断路器(以下简称断路器)的技术要求、试验方法与试验规则、标志包装运输贮存等内容。 本标准适用于机车及动车组用真空断路器，不适用于空气断路器。

Technical conditions of locomotive vacuum circuit breaker

NF F74-122-1:1999 轨道交通.固定设备.第1部分:与电气安全和接地有关的防护设备

Railway applications - Fixed installations - Part 1 : protective provisions relating to electrical safety and earthing.

DIN EN 50123-5/A1:1999 轨道交通.固定设备.直流开关设备.第5部分:直流系统专用电涌放电器与低压限制器,修改件1

Railway applications - Fixed installations; D.C. switchgear - Part 5: Surge arresters and low-voltage limiters for specific use in d.c. systems; Amendment A1; German version EN 50123-5:1997/A1:1999

DIN EN 50123-7-3:1999 轨道交通.固定设备.直流开关.第7部分:直流牵引设备专用测量、控制与保护装置.第3节:绝缘电压交换器与其他电压测量装置

Railway applications - Fixed installations; D.C. switchgear - Part 7: Measurement, control and protection devices for specific use in d.c. traction systems; Section 3: Isolating voltage transducers and other voltage measuring devices; German version EN 50

DIN EN 50123-7-2:1999 轨道交通.固定设备.直流开关.第7部分:直流牵引设备专用测量、控制与保护装置.第2节:绝缘电流变换器与其他电流测量装置

Railway applications - Fixed installations; D.C. switchgear - Part 7: Measurement, control and protection devices for specific use in d.c. traction systems; Section 2: Isolating current transducers and other current measuring devices; German version EN 50

IEC 60349-1:1999 电力牵引 铁路与道路车辆用旋转电机 第1部分:除电子变流器供电的交流电动机之外的旋转电机

1 This part of IEC 60349 is applicable to rotating electrical machines, other than electronic convertor-fed alternating current motors, forming part of the equipment of electrically propelled rail and road vehicles. The vehicles may obtain power either from an external supply or from an internal source. The object of this standard is to enable the performance of a machine to be confirmed by tests and to provide a basis for assessment of its suitability for a specified duty and for comparison with other machines. NOTE 1 This standard also applies to machines installed on trailers hauled by electrically propelled vehicles. NOTE 2 The basic requirements of this standard may be applied to rotating electrical machines for special purpose vehicles such as mine locomotives, but it does not cover flameproof or other special features that may be required. NOTE 3 It is not intended that this standard should apply to machines on small road vehicles such as battery-fed delivery vehicles, works trucks, etc. Neither does it apply to minor machines such as windscreen wiper motors, etc. that may be used on all types of vehicles. NOTE 4 Industrial type machines complying with the IEC 60034 series may be suitable for certain auxiliary applications. 2 Electrical inputs or outputs of machines covered by this standard may be as follows: a) direct current (including rectified polyphase alternating current); b) pulsating current (rectified single-phase alternating current); c) unidirectional chopper-controlled current; d) single-phase alternating current; e) polyphase alternating current (in general three-phase). 3 In this standard, the electrical machines concerned are classified as follows. 3.1 Traction motors Motors for propelling rail or road vehicles. 3.2 Engine-driven main generators Generators for supplying power to traction motors on the same vehicle or train. 3.3 Main motor-generator sets Machines obtaining power from a line or battery, and supplying power to traction motors on the same vehicle or train.

Electric traction - Rotating electrical machines for rail and road vehicles - Part 1: Machines other than electronic convertor-fed alternating current motors

NF R13-481:1999 道路车辆.车装非防水连接器用连接接口.有1.5mm和/或2.8mm两列触点的连接器

Road vehicles. Connection interface for on-board no waterproof connectors. Connectors with two rows of 1,5 mm and/or 2,8 mm category contact.

NF F42-123-4:1999 轨道交通.固定装置.直流开关设备.第4部分:室外直流在线开关和直流接地开关

Railway applications - Fixed installations - D.C. switchgear - Part 4 : outdoor d.c. in-line switch-disconnectors and d.c. earthing switches.

IEC 60077-1:1999 轨道交通.机车车辆用电气设备 第1部分:一般运行条件和一般规则

本部分规定了机车车辆主电路、辅助电路、控制和指示电路上电气设备的一般使用条件和要求。 注：这些规则中的某些条款，由制造商与用户协商后，可适用于其他机车车辆(如矿山机车、有轨电车等)上的设备。 本部分目的在于尽可能规范机车车辆电气设备中具有共性的规则和要求，以达到对设备要求和试 验的一致性，从而避免按不同的标准进行试验。 本部分涉及了所有与正常使用条件下预期环境条件、结构、性能及相应的一般性试验相关的要求， 以及受到广泛关注和应用的特殊领域如温升、介电特性等。

Railway applications - Electric equipment for rolling stock - Part 1: General service conditions and general rules

BS EN 50206-2:1999 轨道交通.轨道车辆.集电器:特征和试验.城市铁路和轻轨车辆用的集电器

This standard defines the general assembly characteristics, which are to be applied to pantographs, to enable current collection from the overhead line system. It also defines the tests the pantographs have to perform, excluding insulators. This standard does not apply to pantograph dielectric tests, which are to be performed on the pantograph installed on the vehicle roof. This standard does not apply to pantographs used on main line vehicles; these pantographs are considered in EN 50206-1. This standard relates to conventional suspended overhead line systems and accessories. The systems (or part of them) which are rigidly suspended will require special consideration between the customer and the supplier.

Railway applications - Rolling stock - Pantographs - Characteristics and tests - Pantographs for metros and light rail vehicles