T11 发动机与附属装置 标准查询与下载

GM VOL II SEC V-1977 V部分-投影焊接螺钉

Alternative test method: Water penetration,requirement no leakage. Galler bara for ljusa farger 2) 2 is only valid for light colours Bedomning enligt STD 3816, 3.1 3) Assessment according to STD 3816E, 3.1 Copyright General Motors Europe Reproduced by

Section V - Projection Weld Screws

GM VOL II SEC T-1977 T部分-攻丝螺钉

Hoghallfast isotropiskt presstal med god formbarhet och god svetsbarhet. Materialet har fatt sin hoga hallfasthet genom legering med en liten mangd Titan.

Section T - Tapping Screws

GM VOL II SEC V-1975 V部分-自锁螺母

Freigabemuster, für die diese Vorschrift zutrifft, müssen nach dieser Vorschrift geprüft werden und von der Produktentwicklung und Konstruktion genehmigt sein

Section V - Self-Piercing Nuts

GM VOL II SEC V-1974 V部分-管螺母

Gummit ska foretradesvis anvandas nar kravljuddampande formaga prioriteras. The rubber is primarily intended to be used when given priority to sound deadening properties.

Section V - Tube Nuts

GM VOL II SEC V-1973 V部分-不同金属螺纹接触长度测量的设计准则

Fiberamnen med olika ytvikter somsatsas iett verktyg

Section V - Hexagon Bolts

GM VOL II SEC V-1972 V部分-平垫圈

Brannbarhet/Combustibility STD 232 mm/min max 75 75 Klimatcykling Climate cycling Cykel/Cycle B STD 3907 Delamination far ej uppsta Delamination must not occur Termisk konduktivitetThermal conductivity W/mK

Section V - Machine Screws

BS AU 141a:1971 道路车辆用柴油机性能规范

This British Standard applies to compression ignition (diesel) engines, utilizing liquid fuel only, for propelling vehicles designed primarily for use on the public highway. It specifies the standard test conditions for the test bed procedure, the equipment to be included on the engine for standard tests at the approved engine power outputs and the smoke control of the exhaust gases under 'steady state' conditions. It includes a type test, incorporating a 100 h test, and output tolerances and exhaust gas opacity limits on production engines. NOTE. The titles of the British Standards referred to in this stan-dard are listed in the Foreword.

Specification for the performance of diesel engines for road vehicles

GM VOL II SEC T-1965 T部分-球接头

The material is a partially cross-linked, chlorinated olefin and is intended primarily for injection moulding.

Section T - Ball Joints

GM VOL II SEC T-1962 T部分-环形垫圈

The material is intended for compression moulded parts.

Section T - Annular Gaskets

GM VOL II SEC T-1960 T部分-橡胶气管

The material is intended for injection moulded parts.

Section T - Rubber Grommets

GM VOL II SEC T-1951 T部分-杆底的接头件及孔

Stickad polyester Knitted polyester

Section T - Rod End Clevises and Eyes

ZB/T T06002-1989 汽车发动机镶耐磨圈活塞金相标准

Metallographic standard for pistons with wear-resistant rings inlaid with automobile engines

HBm 91-1990 涡轮膨胀机组通用技术条件

本标准规定了油田气轻烃回收装置中的涡轮膨胀机组（以下简称膨胀机组，包括涡轮膨胀机、润滑系统、气封气系统、测控系统和底盘等五部分）的基本技术要求、试验方法和检验规则等。 　　本标准适用于采用油压轴承且工作介质为油田气的膨胀机组。采用气体轴承或滚动轴承以及工作介质为其它气体的涡轮膨胀机组亦可参照执行。

General Specifications for Turbo Expanders