T13 进排气与燃油供给系统 标准查询与下载

ANSI/ABYC A-26-2012 液化石油气(LPG)和压缩天然气(CNG)燃料器具

This standard is a guide for the design, construction, installation, and maintenance of LPG and CNG fueled appliances.

LPG and CNG Fueled Appliance

ANSI/CSA NGV2a-2012 压缩天然气车辆燃料容器

Compressed Natural Gas Vehicle Fuel Containers

ANSI NGV 2b-2012 压缩天然气车辆油箱

Compressed Natural Gas Vehicle Fuel Containers

ANSI/ABYC H-24-2012 汽油燃油系统

This standard is a guide for the design, choice of materials for,construction, intallation, repair, and maintenance of permanently installed gasoline fuel systems.

Gasoline Fuel Systems

DB34/T 1559-2011 汽车空气干燥器性能要求及台架试验方法

本标准适用于汽车制动系统使用的空气干燥器。

Performance requirements and bench test methods for air dryer used in automobile

SAE J226-2011 发动机预热器

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Standard describes electric immersion engine preheaters for use in the coolant jacket of heavy-duty and intermediate size diesel engines. This document gives the dimensional information of the four basic styles of engine preheaters. The tables for each style will list the wattage commonly used. Small engines that typically require less than 600 W of preheat for cold weather starter are not covered by this document. These types of engines generally have very little space available to accommodate an immersion heater of the styles presented in this document. The purpose of this document is to establish commonality of engine preheater designs. The user of this document can use these current styles and wattages early on in their designing. This will give the user of this document a good engine preheater design.

Engine Preheaters

SAE J1350-2011 燃烧柴油,汽油和丙烷的液体冷却发动机预热器的选择和应用指南

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This information report covers fuel fired preheaters which burn gasoline, diesel, or propane fuels. This type of heater must be used in remote areas where 110/220 V, 60 Hz electric power is not available, and is recommended anywhere an on-board self-contained system is required. the guidelines in this report are applicable, but not limited to, fuel burning heater installations on the off-road self-propelled work machine described in SAE Recommended Practice J1116.

Selection and Application Guidelines for Diesel, Gasoline, and propane Fired Liquid Cooled Engine Pre-Heaters

SAE J1422-2011 柴油机燃料加温器

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Information Report establishes performance requirements for devices used to warm diesel fuel before entering the fuel filter(s). This document applies to all off-road, self-propelled, diesel-powered work machines described in SAE J1116. This document may be applied to other diesel equipment.

Fuel Warmer Diesel Engines

SAE J2079-2011 柴油机乙醚喷雾器位置

This document has been declared "Stabilized" and will no longer be subjected to periodic reviews for currency. Users are responsible for verifying references and continued suitability or technical requirements. New technology may exist. This SAE Information Report recommends the requirements for the location of ether atomizers.

Location of Atomizer of Ether Systems for Diesel Engines

SAE J1645-2011 减少静电荷用燃料系统和部件

This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: Fuels that are in a liquid state at ambient temperatures and atmospheric pressures and are contained in vehicle fuel tanks that operate at or near atmospheric pressure. This includes gasoline and diesel fuels as well as their blends with additives such as alcohols, esters and ethers whether the additives are petroleum based or bio-fuel based; The group of components that comprise the fuel system (in contact and not in contact with fuels); Other components in proximity to the fuel system that may be affected by electrostatic fields caused by the fuel system; Electrostatic phenomena that arise from or are affected by the following aspects of vehicle or fuel system operation: Flowing fuel in the fuel delivery system; Flowing fuel being dispensed to the vehicle while it is being fueled

Fuel Systems and Components Electrostatic Charge Mitigation

UL SUBJECT 2583-2011 燃料箱附件调查大纲

1.1 These requirements cover mechanical type accessories that are typically intended for attachment to storage tanks or connecting pipe in commercial (public) or private (fleet) automotive fueling station applications, and are designed to provide automatic safety or operational functions. 1.2 These products may be used with underground or aboveground tank systems and with liquid and/or vapor phases of the fuels covered by each Part of this Outline as identified below: 1.2.1 Part I Vapor Control Products – Functional devices and accessories intended for connection to tank top openings (directly on fittings or indirectly on pipe) and perform safety or operational functions, such as emergency vents, normal vents, adapters and caps. 1.2.2 Part II Liquid Control Products (reserved for future use) – Liquid control products such as overfill containment devices, overfill prevention devices, and flow restrictors. 1.2.3 Part III Structural and Containment Products (reserved for future use) – Metallic components such as access devices, manways, supports, and dikes. 1.2.4 Part IV Corrosion Protection Products (reserved for future use) – Nonmetallic components such as tank anchors, dielectric bushings, anode packs, coatings and resins. 1.2.5 Part V Miscellaneous Products (reserved for future use) – Miscellaneous products such as lift lugs, striker plates and monitor well caps. 1.3 These products are intended for use with storage tanks or fueling systems containing automotive fuels under the expected use conditions and exposures that have similar chemical, physical and material compatibility properties as represented in these requirements. The use fuels are intended to be formulated in accordance with 40 CFR Part 80 “Regulation of Fuels and Fuel Additives” and meet the following ASTM Fuel Specifications and blend limitations: a) ASTM D975, Standard Specification for Diesel Fuel Oils, with biodiesel blends up to a maximum of 5 percent (B5); b) ASTM D7467, Standard Specification for Low Blend Biodiesel, with biodiesel blends between 6 to 20 percent (B6 to B20); c) ASTM D4814Standard Specification for Automotive Spark-Ignition Engine Fuel, gasoline or oxygenated gasoline, with limited ethanol blends up to a maximum of 10 percent (E10); d) ASTM D5798, Standard Specification for Fuel Ethanol (Ed75 – Ed85) for Automotive Spark- Ignition Engines, high blend ethanol, with gasoline/ethanol mixtures in the nominal E85 range (E70 – E90); and e) Mid Range Ethanol Blends (E11 to E69) using variable mixtures of ASTM D4814, Low Blend Ethanol and ASTM D5798, High Blend Ethanol. 1.4 Products covered by this Outline are intended to be installed and used in accordance with one or more of the following: a) NFPA 30, Flammable and Combustible Liquids Code; b) NFPA 30A, Code for Motor Fuel Dispensing Facilities and Garages; c) NFPA 1, Uniform Fire Code; d) International Fire Code published by the International Fire Council; or e) Other Applicable Federal and State regulations for the specific product or application it is being utilized in. 1.5 These products are factory manufactured and intended for in-shop or on-site assembly, inspection and testing for the specified application and use conditions by qualified persons in accordance with the manufacturer’s instructions and local requirements. 1.6 These products are intended to be periodically inspected and maintained for continued service, or taken out of service if necessary, by qualified persons in accordance with industry recommended practices and/or the manufacturer’s instructions. 1.7 These products have not been evaluated for use after natural disasters, fires or exposures to chemicals not representative of the test liquids/vapors or excessive physical damage beyond the expected assembly, installation and uses as identified in these requirements.

Outline of Investigation for Fuel Tank Accessories

SAE J244-2011 柴油机引擎的进气或排气气流的测量

This SAE Recommended Practice is intended to provide guidance for the proper measurement of combustion air flow into diesel engines as utilized in engine test cell environments.

Measurement of Intake Air or Exhaust Gas Flow of Diesel engines

SAE J614-2011 发动机和变速箱油尺标记

This SAE Recommended Practice provides information useful in the marking of engine and transmission dipsticks used for fluid level indication.

Engine and Transmission Dipstick Marking

BS ISO 12251:2011 柴油机.‎夹紧式CR燃油喷射器.安装尺寸规格

Diesel engines. Clamp mounted CR fuel injectors. Mounting dimensions

SAE J2793-2011 燃料分配过滤器试验方法

This SAE Recommended Practice is applicable to gasoline and diesel fuel filters installed on fuel dispensing equipment, mobile or stationary. It describes a set of tests used to characterize the structural integrity, filtration performance, and reaction to water contaminant with fuel dispensing filters. To provide a standardized method for evaluating performance characteristics on laboratory bench equipment. The laboratory data may be utilized with actual field data to establish dispensing filter performance specifications.

Fuel Dispensing Filter Test Methods

ISO 12251:2011 柴油发动机.夹具安装的燃油喷射器.安装尺寸规格

This International Standard specifies dimensional requirements for clamp mounted CR fuel injectors and their corresponding cylinder head features in diesel engines. According to the injector nozzle capnut, the clamp mounted CR fuel injectors can be divided into two types: a) Type A, where the nozzle capnut is straight (see Figure 4). b) Type B, where the nozzle capnut is stepped (see Figure 5). Each clamp mounted CR fuel injector type is subdivided by a series of different sizes. NOTE This differentiation corresponds to the relationship between the two guide diameters of the clamp mounted CR fuel injectors.

Diesel engines.Clamp mounted CR fuel injectors.Mounting dimensions

KS R ISO 7876-5:2010 燃料喷射设备.词汇.第5部分:通用轨燃料喷射系统

이 표준은 디젤(압축 착화) 엔진의 코먼 레일 연료 분사 장치와 그 구성 부품에 대한 용어

Fuel injection equipment－Vocabulary－Part 5：Common rail fuel injection system

KS R ISO 7612:2010 柴油机.共轨燃料喷射系统用基座安装直列燃料喷射泵和高压供给泵.安装尺寸

이 표준은 디젤(압축 점화) 엔진용 코먼 레일 연료 분사 장치의 베이스 장착 직렬형 연료

Diesel engines-Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems-Mounting dimensions

SAE J1488-2010 乳化水/油分离试验规程

To determine the ability of a fuel/water separator to separate emulsified or finely dispersed water from fuels. This test method is applicable for biodiesel fuel.

Emulsified Water/Fuel Separation Test Procedure

SAE J1839-2010 粗糙微滴水/燃料分离试验规程

To determine the undissolved water removal performance of a fuel/water separator under controlled laboratory conditions, using water droplets. this test method is applicable for diesel and biodiesel fuel.

Coarse Droplet Water/Fuel Separation Test Procedure