T24 制动系统 标准查询与下载

ISO 14794:2011 重型商用车辆与公共汽车.转弯制动.开环试验方法

This International Standard specifies open-loop test methods for determining the effect of braking on the course-holding and directional behaviour of heavy vehicles or heavy vehicle combinations when braking is accomplished using - the service-brake system, or - the retarder or engine brake only. This International Standard is applicable to heavy vehicles — i.e. commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 — covered by Categories M3, N2, N3, O3 and O4 of UNECE (United Nations Economic Commission for Europe) and EC vehicle regulations. These categories pertain to trucks and trailers with a maximum mass above 3,5 t and to buses and articulated buses with a maximum mass above 5 t.

Heavy commercial vehicles and buses - Braking in a turn - Open-loop test methods

SAE J1409-2011 空气制动阀试验规程

This SAE Recommended Practice establishes uniform test procedures for air brake systems pneumatic valves with respect to: a. input-output characteristics; b. leakage measurement; c. low temperature evaluation; d. elevated temperature evaluation; e. corrosion resistance evaluation; f. endurance testing; g. structural integrity; h. vibration testing. This document establishes uniform accelerated laboratory test procedures for evaluating comparative performance characteristics of pneumatic valves designed to operate in 931 kPa (135 psi) nominal air brake systems. These tests are based upon current industry practices.

Air Brake Valves Test Procedure

SAE J3001-2011 制动器绝缘体阻尼测量规程

This procedure is applicable to modes between 1500 and 15 000 Hz. The parameters measured with this procedure are defined as the damping factor ξ for the first three bending modes of the beam. The procedure will focus on bending modes only.

Brake Insulator Damping Measurement Procedure

JIS D 0107:2011 道路车辆.制动装置.词汇表

This standard specifies the glossary of terms relating to braking equipment to be used for automobiles.

Road vehicles -- Braking equipments -- Vocabulary

JIS D 0106:2011 道路车辆.制动类型,制动机械和制动操作.词汇表

This Standard specifies terms related to types, mechanics and operation of brakes used for road vehicles.

Road vehicles -- Brake types, braking mechanics and brake operation -- Vocabulary

KS R ISO 2974:2010 柴油机.60度锥孔的高压油管接头管端部连接

이 표준은 디젤(압축 착화) 엔진 연료 분사 장치에 대한 고압 파이프 끝부분 연결의 치수

Diesel engines-High-pressure fuel injection pipe end-connections with 60°female cone

BS ISO 6312:2010 道路车辆.制动闸衬.圆盘制动片和鼓式制动器蹄片装置的剪切试验程序

Road vehicles. Brake linings. Shear test procedure for disc brake pad and drum brake shoe assemblies

SAE J293-2010 卡车和公交车等级停车性能要求

This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to vehicle classification, vehicle load, percent grade, and application force. This document presents on-grade parking performance requirements for new motor vehicles and trailers intended for roadway use.

Truck and Bus Grade Parking Performance Requirements

SAE J92-2010 雪上汽车油门控制系统

This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand throttle control systems. This recommendation is not intended to cover competition vehicles nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand control systems using an outer flexible conduit with a multiple strand inner cable, the basic requirements of freedom of movement, strength, material, etc. will apply to any system.

Snowmobile Throttle Control Systems

SAE J1279-2010 机动雪橇驱动机制

This SAE Recommended Practice is applicable to snowmobiles as defined in SAE J33. To provide minimum requirements and tests for evaluating the structural integrity of snowmobile drive mechanisms (that is, drive pulleys, driven pulleys, torque convertors, centrifugal clutches, or similar mechanisms).

Snowmobile Drive Mechanisms

SAE J2378-2010 拖车储气缸填充和停车松开制动器时间用试验规程

This SAE Recommended Practice provides instructions and test procedures for air braked trailers and dollies used in single and multiple trailer combinations on highway. This document is not intended for off-highway application. This document provides a method of determining the efficiency of trailer and dolly air supply systems in filling reservoirs and, for those with spring applied parking brakes, in releasing parking brakes.

Test Procedure for Trailer Air Reservoir Fill and Parking Brake Release Times

SAE J1402-2010 汽车汽闸制动软管和软管组件

This recommended practice covers minimum requirements for air brake hose assemblies made from reinforced elastomeric hose and suitable fittings for use in automotive air brake systems including flexible connections from frame to axle, tractor to trailer, trailer to trailer and other unshielded air lines with air pressures up to 1 MPa, that are exposed to potential pull or impact. This hose is not to be used where temperatures, external or internal, fall outside the range of -40°C to +100°C.

Automotive Air Brake Hose and Hose Assemblies

ISO 6312:2010 道路车辆.制动闸衬.圆盘制动片和鼓式制动器蹄片装置的剪切试验规程

Road vehicles - Brake linings - Shear test procedure for disc brake pad and drum brake shoe assemblies

SAE J1513-2010 外部自动间隙调整器性能要求

These performance requirements have been established for external automatic slack adjusters when tested to SAE J1462.

External Automatic Slack Adjuster Performance Requirements

SANS 957:2010 道路车辆．制动闸衬．压缩应变试验方法

Specifies a method for test and measurement of the compressive displacement of brake linings or brake pad assemblies due to loading and temperature. Also provides a test method to assess lining thermal swell and growth. Applies to disc brake pad assembli

Road vehicles - Brake linings - Compressive strain test methods

JJG(交通) 100-2010 双轮式横向力摩擦系数自动测试系统

本规程适用于双轮式横向力摩擦系数自动测试系统(以下简称双轮式测试系统)的首次检定、后续检定和使用中的检验。

Automatic Testing System of Twin-wheel Sideway Force Coefficient

JJG(交通) 099-2010 路面制动式摩擦系数自动测试系统

本规程适用于路面制动式摩擦系数自动测试系统(以下简称制动式测试系统)的首次检定、后续检定和使用中的检验。

Automatic Testing System of Road Braking Friction Coefficient

BS ISO 7628:2010 道路车辆.气闸系统用热塑性塑料管

Road vehicles - Thermoplastics tubing for air braking systems

SAE J1926-1-2010 一般用途和流体传动管接头.带ASME B1.1螺纹和O形圈密封的油口和螺纹端头.第1部分:带锪孔沟槽中装有O形密封圈的油口

This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads in accordance with ASME B1.1 for use with adjustable and nonadjustable stud ends shown in SAE J1926-2 and SAE J1926-3. Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.

Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing Part 1: Threaded Port with O-Ring Seal in Truncated Housing

SAE J1609-2010 空气储气罐容量性能执行操纵卡车和客车

This SAE Recommended Practice establishes performance guidelines for the capacity of the air reservoir systems used on trucks, towing trucks, truck-tractors, trailers, and converter dollies with GVWRs over 10 000 lb, designed to be used on the highway. NOTE: Compliance with this document does not guarantee compliance with the air reservoir requirements of FMVSS 121. The purpose of this document is to establish a minimum air storage capacity for highway-type trucks, buses, trailers, and converted dollies which use compressed air to actuate or transmit actuation power to the foundation brakes. A vehicle's air reservoir capacity is quantified by its ability to provide a brake application pressure which is adequate to stop the vehicle within the emergency brake stopping distances specified in Table II of FMVSS 121, after seven full brake applications with the air compressor disabled.

Air Reservoir Capacity Performance Guide Trucks and Buses